Anthony I. Huber
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Anthony I. Huber has a total of 68 co-authors. Here are the top co-authors by number of shared publications:
- James Burgoyne
University of British Columbia
5 shared publications - Anna K. Vaskuri
National Institute of Standards and Technology
4 shared publications - Steve K. Choi
Department of Physics and Astronomy University of California 92521 Riverside CA USA
4 shared publications - Cody J. Duell
Cornell University
3 shared publications - Darshan A. Patel
Cornell University
3 shared publications Ema Smith
Cornell University
3 shared publications
Latest Publications
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (6) , 1-7
CCAT: Mod-Cam Cryogenic Performance and Its Impact on 280-GHz KID Array Noise
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (6) , 1-7
CCAT: Mod-Cam Cryogenic Performance and Its Impact on 280-GHz KID Array Noise
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (6) , 2402506
CCAT: Optical Responsivity, Noise, and Readout Optimization of KIDs for Prime-Cam
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (6) , 2402506
CCAT: Optical Responsivity, Noise, and Readout Optimization of KIDs for Prime-Cam
- 4 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (6) , 1500708
CCAT: Silicon-Platelet Feedhorns for Submillimeter Wavelengths
Silicon-platelet feedhorn arrays are an established technology at millimeter wavelengths that, for some applications, can provide significant advantages over traditional direct-machined metal feedhorns. The Prime-Cam focal planes operating in the 350 GHz ($\sim$860 $\mu$m) and 850 GHz ($\sim$350 $\mu$m) bands are anticipated to carry the first silicon-platelet feedhorn arrays to operate fully at submillimeter wavelengths, representing a significant step forward in the application of this technology. In particular, the feedhorns designed for operation in the 850 GHz band represent a 3x increase in frequency compared to previously demonstrated and deployed devices of this type. Here we present a demonstration of silicon-platelet feedhorns at these submillimeter wavelengths, including in-lab performance characterization. We present fabrication metrology, room-temperature beam maps, and cryogenic optical efficiency measurements where the feedhorns are coupled to prototype CCAT Prime-Cam detectors. We show that feedhorn performance measurements are well matched to simulation and compare that performance directly to traditional, direct-machined metal feedhorns.
- 4 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (6) , 1500708
CCAT: Silicon-Platelet Feedhorns for Submillimeter Wavelengths
Silicon-platelet feedhorn arrays are an established technology at millimeter wavelengths that, for some applications, can provide significant advantages over traditional direct-machined metal feedhorns. The Prime-Cam focal planes operating in the 350 GHz ($\sim$860 $\mu$m) and 850 GHz ($\sim$350 $\mu$m) bands are anticipated to carry the first silicon-platelet feedhorn arrays to operate fully at submillimeter wavelengths, representing a significant step forward in the application of this technology. In particular, the feedhorns designed for operation in the 850 GHz band represent a 3x increase in frequency compared to previously demonstrated and deployed devices of this type. Here we present a demonstration of silicon-platelet feedhorns at these submillimeter wavelengths, including in-lab performance characterization. We present fabrication metrology, room-temperature beam maps, and cryogenic optical efficiency measurements where the feedhorns are coupled to prototype CCAT Prime-Cam detectors. We show that feedhorn performance measurements are well matched to simulation and compare that performance directly to traditional, direct-machined metal feedhorns.
- Open Access
- 1 April 2025
- Published by SPIE-Intl Soc Optical Eng in Journal of Astronomical Telescopes, Instruments, and Systems
- Vol. 11 (02) , 026005-16
280-GHz aluminum MKID arrays for the Fred Young Submillimeter Telescope
The Fred Young Submillimeter Telescope (FYST) of the CCAT Collaboration has a 6-m clear aperture, and it is being constructed on Cerro Chajnantor in the Chilean Atacama Desert at an elevation of 5600 m. Prime-Cam1 is one of the two receivers being built for FYST, the other being the CCAT Heterodyne Array Instrument.2 Prime-Cam’s science goals include observing galactic ecology, Sunyaev–Zel’dovich effect, galaxy evolution, and line intensity mapping.1,3 Prime-Cam is designed to be capable of operating in the millimeter to submillimeter (100 GHz to 1.5 THz) range with focal planes made of superconducting microwave kinetic inductance detector (MKID) arrays.
- 1 April 2025
- Published by SPIE-Intl Soc Optical Eng in Journal of Astronomical Telescopes, Instruments, and Systems
- Vol. 11 (02) , 026005-16
Open Access280-GHz aluminum MKID arrays for the Fred Young Submillimeter Telescope
The Fred Young Submillimeter Telescope (FYST) of the CCAT Collaboration has a 6-m clear aperture, and it is being constructed on Cerro Chajnantor in the Chilean Atacama Desert at an elevation of 5600 m. Prime-Cam1 is one of the two receivers being built for FYST, the other being the CCAT Heterodyne Array Instrument.2 Prime-Cam’s science goals include observing galactic ecology, Sunyaev–Zel’dovich effect, galaxy evolution, and line intensity mapping.1,3 Prime-Cam is designed to be capable of operating in the millimeter to submillimeter (100 GHz to 1.5 THz) range with focal planes made of superconducting microwave kinetic inductance detector (MKID) arrays.
- 16 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-4
CCAT: LED Mapping and Characterization of the 280 GHz TiN KID Array
Prime-Cam, one of the primary instruments for the Fred Young Submillimeter Telescope (FYST) developed by the CCAT Collaboration, will house up to seven instrument modules, with the first operating at 280 GHz. Each module will include three arrays of superconducting microwave kinetic inductance detectors (KIDs). The first KID array fabricated for the 280 GHz module uses titanium-nitride (TiN) as the superconducting material and has 3,456 individual detectors, while the other two arrays use aluminum. This paper presents the design and laboratory characterization of the 280 GHz TiN array, which is cooled below its critical temperature to $\sim$ 0.1K and read out over six RF feedlines. LED mapping, a technique for matching the measured resonant frequency of a detector to its physical position, was performed on the array so that the results can be used to lithographically trim the KID capacitors and increase the yield of the array by reducing frequency collisions. We present the methods and results of LED mapping the 280 GHz TiN KID array before deployment on FYST.
- 16 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-4
CCAT: LED Mapping and Characterization of the 280 GHz TiN KID Array
Prime-Cam, one of the primary instruments for the Fred Young Submillimeter Telescope (FYST) developed by the CCAT Collaboration, will house up to seven instrument modules, with the first operating at 280 GHz. Each module will include three arrays of superconducting microwave kinetic inductance detectors (KIDs). The first KID array fabricated for the 280 GHz module uses titanium-nitride (TiN) as the superconducting material and has 3,456 individual detectors, while the other two arrays use aluminum. This paper presents the design and laboratory characterization of the 280 GHz TiN array, which is cooled below its critical temperature to $\sim$ 0.1K and read out over six RF feedlines. LED mapping, a technique for matching the measured resonant frequency of a detector to its physical position, was performed on the array so that the results can be used to lithographically trim the KID capacitors and increase the yield of the array by reducing frequency collisions. We present the methods and results of LED mapping the 280 GHz TiN KID array before deployment on FYST.
- 16 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-7
High-Density Photon-Noise-Limited Multi-Octave Submillimeter Kinetic Inductance Detectors for the Prime-Cam 850 GHz Module
The Prime-Cam instrument is a first generation instrument under development for the 6-m Fred Young Submillimeter Telescope (FYST), which will be sited on Cerro Chajnantor in the Chilean Atacama Desert at an elevation of 5600 m. Among the instrument modules planned for the Prime-Cam instrument, the 850 GHz module is the highest frequency and of particular importance to the astronomical community due to the absence of near-future proposals for instruments at similar wavelengths and at equivalent sites. Success of the 850 GHz module hinges on the development of state-of-the-art detector arrays. The 850 GHz module will consist of approximately 45,000 titanium-nitride, polarization-sensitive, lumped-element kinetic inductance detectors, meaning the module will field more microwave kinetic inductance detectors than any other millimeter-wave receiver to date. The detectors are being designed to be read out using a multi-octave readout architecture, allowing for approximately double the multiplexing of other CCAT modules. We present the parameter space explored in the development of these detectors, including testing a means of shorting inductors to modify the resonance with minimal changes to the absorber architecture and testing different volumes of the inductor. Results and optical characterization of the prototype pixels for the 850 GHz instrument module are presented. The 850 GHz module is expected to be observing in 2026.
- 16 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-7
High-Density Photon-Noise-Limited Multi-Octave Submillimeter Kinetic Inductance Detectors for the Prime-Cam 850 GHz Module
The Prime-Cam instrument is a first generation instrument under development for the 6-m Fred Young Submillimeter Telescope (FYST), which will be sited on Cerro Chajnantor in the Chilean Atacama Desert at an elevation of 5600 m. Among the instrument modules planned for the Prime-Cam instrument, the 850 GHz module is the highest frequency and of particular importance to the astronomical community due to the absence of near-future proposals for instruments at similar wavelengths and at equivalent sites. Success of the 850 GHz module hinges on the development of state-of-the-art detector arrays. The 850 GHz module will consist of approximately 45,000 titanium-nitride, polarization-sensitive, lumped-element kinetic inductance detectors, meaning the module will field more microwave kinetic inductance detectors than any other millimeter-wave receiver to date. The detectors are being designed to be read out using a multi-octave readout architecture, allowing for approximately double the multiplexing of other CCAT modules. We present the parameter space explored in the development of these detectors, including testing a means of shorting inductors to modify the resonance with minimal changes to the absorber architecture and testing different volumes of the inductor. Results and optical characterization of the prototype pixels for the 850 GHz instrument module are presented. The 850 GHz module is expected to be observing in 2026.