Lin Jiang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Lin Jiang has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Ping Xue
College of Mechanical and Electrical Engineering Beijing University of Chemical Technology Beijing China
5 shared publications- Chenchao Fu
College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, Beijing 100029, China
4 shared publications Run Zhang
College of Mechanical and Electrical Engineering Beijing University of Chemical Technology Beijing China
4 shared publications- Zetian Hua
College of Mechanical and Electrical Engineering Beijing University of Chemical Technology Beijing China
4 shared publications - Mingfei Liu
College of Mechanical and Electrical Engineering Beijing University of Chemical Technology Beijing China
3 shared publications - Run Zhang
College of Mechanical and Electrical Engineering Beijing University of Chemical Technology Beijing China
2 shared publications
Latest Publications
- 16 August 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (19)
High‐Strength and Transparent Ultrahigh‐Molecular‐Weight Polyethylene via Die Drawing: Effect of Drawing Ratio
Ultrahigh‐molecular‐weight polyethylene (UHMWPE) is an engineering polymer renowned for its excellent wear resistance, impact toughness, and low friction. However, products obtained by conventional melt processing are typically opaque and exhibit limited improvements in strength, which restricts their application in high‐performance structural and optical‐related fields. In this study, solid‐state die drawing was employed to fabricate UHMWPE sheets with different drawing ratios, aiming to achieve simultaneous enhancements in optical transparency and mechanical performance. The influence of the drawing ratio on the structural evolution of UHMWPE, along with the associated changes in thermal behavior, optical transmittance, and mechanical properties, was systematically investigated through multiscale characterization. The results demonstrate that increasing the drawing ratio effectively suppresses spherulitic structures and promotes the formation of a highly oriented microfibrillar morphology. Consequently, internal light‐scattering centers are significantly reduced, leading to markedly enhanced optical transparency. Concurrently, tensile strength and modulus are substantially improved due to enhanced molecular chain orientation and more efficient load transfer. This work highlights the dominant role of drawing ratio in governing the structure–property relationships of UHMWPE during solid‐state die drawing, providing a practical strategy for the fabrication of highly transparent and high‐strength UHMWPE sheets for advanced engineering applications.
- 16 August 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (19)
High‐Strength and Transparent Ultrahigh‐Molecular‐Weight Polyethylene via Die Drawing: Effect of Drawing Ratio
Ultrahigh‐molecular‐weight polyethylene (UHMWPE) is an engineering polymer renowned for its excellent wear resistance, impact toughness, and low friction. However, products obtained by conventional melt processing are typically opaque and exhibit limited improvements in strength, which restricts their application in high‐performance structural and optical‐related fields. In this study, solid‐state die drawing was employed to fabricate UHMWPE sheets with different drawing ratios, aiming to achieve simultaneous enhancements in optical transparency and mechanical performance. The influence of the drawing ratio on the structural evolution of UHMWPE, along with the associated changes in thermal behavior, optical transmittance, and mechanical properties, was systematically investigated through multiscale characterization. The results demonstrate that increasing the drawing ratio effectively suppresses spherulitic structures and promotes the formation of a highly oriented microfibrillar morphology. Consequently, internal light‐scattering centers are significantly reduced, leading to markedly enhanced optical transparency. Concurrently, tensile strength and modulus are substantially improved due to enhanced molecular chain orientation and more efficient load transfer. This work highlights the dominant role of drawing ratio in governing the structure–property relationships of UHMWPE during solid‐state die drawing, providing a practical strategy for the fabrication of highly transparent and high‐strength UHMWPE sheets for advanced engineering applications.
- 12 February 2026
- Published by Wiley in Polymer Engineering & Science
- Vol. 66 (4) , 2891-2900
Numerical Simulation of Polylactic Acid Based Polyurethane Reactive Extrusion Using Rheological Kinetics
Polylactic acid based polyurethane (PLA‐PU) is a high‐performance polymer that can be biodegraded. To achieve its continuous preparation, it is usually synthesized through bulk polymerization in a twin‐screw extruder. During the reaction extrusion process, the physical properties of the material continuously change along the extruder, which is due to the combined effects of flow, heat transfer, and reaction. In this work, the rheological kinetics of PLA‐PU bulk polymerization related to degree of reaction, reaction temperature, and shear rate were established through experiments; the flow and reaction characteristics of conveying elements (CE) and kneading elements (KD) during reactive extrusion were studied through numerical simulations. The results indicate that CE has better pumping ability, but the mixing effect is weaker, which is not conducive to the occurrence of the PLA‐PU polyaddition reaction. KD prolongs the window of the polyaddition reaction by generating reflux, enhances the mixing effect, makes the mixing of various reaction components more uniform, and effectively improves the degree of PLA‐PU polyaddition. Based on the study of the mixing and reaction characteristics of screw elements, the reaction extrusion process of screw element combination was simulated and compared with experimental data under the same geometric shape and reaction conditions. The results indicate that the quality of PLA‐PU can be effectively improved by using more mixing and reverse elements. Through experimental data verification, one‐dimensional numerical simulation of the reactive extrusion process based on rheological kinetics can reveal the flow state and reaction process of the polymerization system, which is beneficial for predicting and optimizing the PLA‐PU reactive extrusion process.
- 12 February 2026
- Published by Wiley in Polymer Engineering & Science
- Vol. 66 (4) , 2891-2900
Numerical Simulation of Polylactic Acid Based Polyurethane Reactive Extrusion Using Rheological Kinetics
Polylactic acid based polyurethane (PLA‐PU) is a high‐performance polymer that can be biodegraded. To achieve its continuous preparation, it is usually synthesized through bulk polymerization in a twin‐screw extruder. During the reaction extrusion process, the physical properties of the material continuously change along the extruder, which is due to the combined effects of flow, heat transfer, and reaction. In this work, the rheological kinetics of PLA‐PU bulk polymerization related to degree of reaction, reaction temperature, and shear rate were established through experiments; the flow and reaction characteristics of conveying elements (CE) and kneading elements (KD) during reactive extrusion were studied through numerical simulations. The results indicate that CE has better pumping ability, but the mixing effect is weaker, which is not conducive to the occurrence of the PLA‐PU polyaddition reaction. KD prolongs the window of the polyaddition reaction by generating reflux, enhances the mixing effect, makes the mixing of various reaction components more uniform, and effectively improves the degree of PLA‐PU polyaddition. Based on the study of the mixing and reaction characteristics of screw elements, the reaction extrusion process of screw element combination was simulated and compared with experimental data under the same geometric shape and reaction conditions. The results indicate that the quality of PLA‐PU can be effectively improved by using more mixing and reverse elements. Through experimental data verification, one‐dimensional numerical simulation of the reactive extrusion process based on rheological kinetics can reveal the flow state and reaction process of the polymerization system, which is beneficial for predicting and optimizing the PLA‐PU reactive extrusion process.
- 17 September 2025
- Published by Wiley in Polymer Engineering & Science
- Vol. 65 (11) , 6248-6261
Effect of Solid Lubricants on Transparency and Mechanical Properties of Solid‐State Drawn UHMWPE
This study systematically investigates the influence of solid lubricants on the transparency and mechanical properties of UHMWPE fabricated via solid‐state drawing. While UHMWPE exhibits exceptional properties, its opaque appearance and relatively low mechanical strength significantly limit its broader applications. The incorporation of solid lubricants (PEW and ZnSt) yields substantial improvements in both transparency and mechanical performance of drawn UHMWPE. All lubricant‐containing samples demonstrate enhanced elongation at break compared to pure UHMWPE, indicating improved molecular chain mobility. Experimental findings reveal that PEW plays a crucial role in enhancing microstructural regularity and filling voids generated during solid‐state drawing, thereby increasing transmittance and reducing haze. Conversely, ZnSt exhibits detrimental effects on optical clarity and haze due to its poor compatibility and significant refractive index mismatch with the UHMWPE matrix. This research provides an in‐depth understanding of the transparency mechanism and elucidates the specific roles of lubricants in the solid‐state drawing. The findings present a highly promising strategy for the development of transparent UHMWPE with optimized mechanical properties.
- 17 September 2025
- Published by Wiley in Polymer Engineering & Science
- Vol. 65 (11) , 6248-6261
Effect of Solid Lubricants on Transparency and Mechanical Properties of Solid‐State Drawn UHMWPE
This study systematically investigates the influence of solid lubricants on the transparency and mechanical properties of UHMWPE fabricated via solid‐state drawing. While UHMWPE exhibits exceptional properties, its opaque appearance and relatively low mechanical strength significantly limit its broader applications. The incorporation of solid lubricants (PEW and ZnSt) yields substantial improvements in both transparency and mechanical performance of drawn UHMWPE. All lubricant‐containing samples demonstrate enhanced elongation at break compared to pure UHMWPE, indicating improved molecular chain mobility. Experimental findings reveal that PEW plays a crucial role in enhancing microstructural regularity and filling voids generated during solid‐state drawing, thereby increasing transmittance and reducing haze. Conversely, ZnSt exhibits detrimental effects on optical clarity and haze due to its poor compatibility and significant refractive index mismatch with the UHMWPE matrix. This research provides an in‐depth understanding of the transparency mechanism and elucidates the specific roles of lubricants in the solid‐state drawing. The findings present a highly promising strategy for the development of transparent UHMWPE with optimized mechanical properties.
- 28 April 2025
- Published by Wiley in Polymer Engineering & Science
- Vol. 65 (7) , 3650-3661
Numerical simulation of PVC resin electrostatic powder coating process and experimental optimization of mechanical properties of CGF/PVC composite prepreg
In this paper, electrostatic powder spraying technology is introduced into the dry powder impregnation process, and CGF/PVC composite prepreg with a thickness of only 0.16 mm is successfully prepared. Through numerical simulation of the electrostatic powder spraying process of PVC resin, it is determined that the powder has a relatively better deposition uniformity on the fiber surface when the static voltage is −90 kV and the spraying distance is 40 mm. It is further verified experimentally and found that the tensile strength of the CGF/PVC composite prepreg prepared under this process can reach 201.6 MPa. This study not only provides a new method for the efficient preparation of continuous fiber reinforced PVC composites but also provides a strong support for the technological progress and application expansion in the field of composites.Highlights: Characterization of field distribution in electrostatic powder spraying at different spraying distances is illustrated. Proposing an innovative process for the preparation of CGF/PVC composite prepreg. An innovative experimental platform for the preparation of CGF/PVC composites prepreg is set up. The thickness of the prepared CGF/PVC composite prepreg is only 0.16 mm. The optimized CGF/PVC composite prepreg has a tensile strength of 201.6 MPa.
- 28 April 2025
- Published by Wiley in Polymer Engineering & Science
- Vol. 65 (7) , 3650-3661
Numerical simulation of PVC resin electrostatic powder coating process and experimental optimization of mechanical properties of CGF/PVC composite prepreg
In this paper, electrostatic powder spraying technology is introduced into the dry powder impregnation process, and CGF/PVC composite prepreg with a thickness of only 0.16 mm is successfully prepared. Through numerical simulation of the electrostatic powder spraying process of PVC resin, it is determined that the powder has a relatively better deposition uniformity on the fiber surface when the static voltage is −90 kV and the spraying distance is 40 mm. It is further verified experimentally and found that the tensile strength of the CGF/PVC composite prepreg prepared under this process can reach 201.6 MPa. This study not only provides a new method for the efficient preparation of continuous fiber reinforced PVC composites but also provides a strong support for the technological progress and application expansion in the field of composites.Highlights: Characterization of field distribution in electrostatic powder spraying at different spraying distances is illustrated. Proposing an innovative process for the preparation of CGF/PVC composite prepreg. An innovative experimental platform for the preparation of CGF/PVC composites prepreg is set up. The thickness of the prepared CGF/PVC composite prepreg is only 0.16 mm. The optimized CGF/PVC composite prepreg has a tensile strength of 201.6 MPa.
- 18 March 2025
- Published by Wiley in Polymer Engineering & Science
- Vol. 65 (5) , 2743-2754
Reaction and rheological kinetics in bulk polymerization of poly(lactic acid)‐based polyurethanes
The apparent viscosity of polylactic acid‐based polyurethane (PLA‐TPU) during the polymerization process is influenced by the reaction progress, reaction temperature, and shear rate. PLA‐TPU with varying degrees of reaction was synthesized via one‐step bulk polymerization, utilizing polylactic acid diol, 4,4′‐diphenylmethane diisocyanate, and 1,4‐butanediol as raw materials. Using torque as the parameter to evaluate the conversion rate of monomers, linear regression yielded the reaction activation energy of 31.84 kJ/mol. The chemical structure, rheological kinetics, and viscosity model of PLA‐TPU were studied using Fourier transform infrared spectroscopy, Nuclear Magnetic Resonance Spectroscopy, Gel permeation chromatography, and the rotary rheometer. The results indicate that under the condition of the shear rate of 1 s−1, the viscosity of the reaction system is proportional to the weight‐average molecular weight raised to the power of 2.8766. The temperature variation follows the Arrhenius equation, with the viscous flow activation energy of 12.83 kJ/mol. The reaction system exhibits pseudoplastic fluid characteristics, and the shear thinning law of its apparent viscosity can be described using the power‐law model, with a flow index of 0.5694. This viscosity model can rapidly predict the apparent viscosity of the PLA‐TPU reaction system under specified conditions. It can serve as a guide for optimizing and designing polymerization reactors, and the modeling process can also offer insights for the study of other stepwise polymerization processes.Highlights: Torque can characterize the conversion rate of monomers in linear polymerization. The molecular weight growth of TPU conforms to the second‐order reaction law. TPU melt is a pseudoplastic fluid that conforms to a power‐law model. Established a viscosity model influenced by time, temperature, and shear rate. The viscosity model can guide the design of reactors.
- 18 March 2025
- Published by Wiley in Polymer Engineering & Science
- Vol. 65 (5) , 2743-2754
Reaction and rheological kinetics in bulk polymerization of poly(lactic acid)‐based polyurethanes
The apparent viscosity of polylactic acid‐based polyurethane (PLA‐TPU) during the polymerization process is influenced by the reaction progress, reaction temperature, and shear rate. PLA‐TPU with varying degrees of reaction was synthesized via one‐step bulk polymerization, utilizing polylactic acid diol, 4,4′‐diphenylmethane diisocyanate, and 1,4‐butanediol as raw materials. Using torque as the parameter to evaluate the conversion rate of monomers, linear regression yielded the reaction activation energy of 31.84 kJ/mol. The chemical structure, rheological kinetics, and viscosity model of PLA‐TPU were studied using Fourier transform infrared spectroscopy, Nuclear Magnetic Resonance Spectroscopy, Gel permeation chromatography, and the rotary rheometer. The results indicate that under the condition of the shear rate of 1 s−1, the viscosity of the reaction system is proportional to the weight‐average molecular weight raised to the power of 2.8766. The temperature variation follows the Arrhenius equation, with the viscous flow activation energy of 12.83 kJ/mol. The reaction system exhibits pseudoplastic fluid characteristics, and the shear thinning law of its apparent viscosity can be described using the power‐law model, with a flow index of 0.5694. This viscosity model can rapidly predict the apparent viscosity of the PLA‐TPU reaction system under specified conditions. It can serve as a guide for optimizing and designing polymerization reactors, and the modeling process can also offer insights for the study of other stepwise polymerization processes.Highlights: Torque can characterize the conversion rate of monomers in linear polymerization. The molecular weight growth of TPU conforms to the second‐order reaction law. TPU melt is a pseudoplastic fluid that conforms to a power‐law model. Established a viscosity model influenced by time, temperature, and shear rate. The viscosity model can guide the design of reactors.
- 15 June 2024
- Published by World Scientific Pub Co Pte Ltd in Functional Materials Letters
- Vol. 17 (06)
Fabrication of flame-retardant PA6/three-dimensional braided glass fiber composites via in situ polymerization
Reaction injection molding method is employed to improve flame retardancy and mechanical properties of three-dimensional braided glass fiber (3D-braided-GF) reinforced in situ polymerized polyamide 6 (PA6) composites. The kernel lies in adding flame retardants, hexaphenoxycyclotriphosphazene (HPCTP), to the reactive monomers to allow it to be in situ filled into composites during preparing PA6 through anionic polymerization, which enables flame retardants to achieve better dispersion. In addition, extremely low-viscosity reactive monomers are easier to immerse in 3D-braided-GF, ameliorating interfacial adhesion between GF and PA6. The preliminary research indicates that samples with 10 wt.% HPCTP concentration can achieve the best mechanical properties and a satisfied flame-retardant grade (UL 94 HB). However, with the incorporation of 15 wt.% HPCTP into samples, the optimum flame-retardant grade (UL 94 V2) and the reduced mechanical performance are obtained. Furthermore, a dual flame retardancy mechanism in both gaseous and condensed phases of samples is further elucidated. This study can provide a reference for scenarios with high requirements for the flame-retardant and mechanical properties, such as high-speed rail and aircraft.
- 15 June 2024
- Published by World Scientific Pub Co Pte Ltd in Functional Materials Letters
- Vol. 17 (06)
Fabrication of flame-retardant PA6/three-dimensional braided glass fiber composites via in situ polymerization
Reaction injection molding method is employed to improve flame retardancy and mechanical properties of three-dimensional braided glass fiber (3D-braided-GF) reinforced in situ polymerized polyamide 6 (PA6) composites. The kernel lies in adding flame retardants, hexaphenoxycyclotriphosphazene (HPCTP), to the reactive monomers to allow it to be in situ filled into composites during preparing PA6 through anionic polymerization, which enables flame retardants to achieve better dispersion. In addition, extremely low-viscosity reactive monomers are easier to immerse in 3D-braided-GF, ameliorating interfacial adhesion between GF and PA6. The preliminary research indicates that samples with 10 wt.% HPCTP concentration can achieve the best mechanical properties and a satisfied flame-retardant grade (UL 94 HB). However, with the incorporation of 15 wt.% HPCTP into samples, the optimum flame-retardant grade (UL 94 V2) and the reduced mechanical performance are obtained. Furthermore, a dual flame retardancy mechanism in both gaseous and condensed phases of samples is further elucidated. This study can provide a reference for scenarios with high requirements for the flame-retardant and mechanical properties, such as high-speed rail and aircraft.
- 30 April 2024
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 38 (2) , 435-450
Research on the performance of three-dimensional-braided-glass fiber reinforced in-situ polymerized TPU
In this study, thermoplastic polyurethane (TPU) is prepared by using 4,4′-methylenediphenyl diisocyanate (4,4′-MDI), poly (1,4-butylene adipate) (PBA), and butane-1,4-diol (BDO). PBA as soft segment for TPU. 4,4′- MDI and BDO as hard segment for TPU. The effects of isocyanate index, hard segment content, and soft segment molecular weight on TPU micro-phase separation, molecular weight, and thermal performance are investigated. 3D-Braided-Glass Fiber (GF) reinforced TPU composites are prepared by in-situ polymerized TPU as the matrix resin. Investigation is conducted into how the mechanical properties and microstructure of the composites are affected by the matrix resin TPU’s structural parameters. As the isocyanate index increases, the mechanical properties of the composites first enhance and then weaken, and the interface bonding between TPU and GF gradually deteriorates. Increasing the molecular weight of soft segments has the same trend of change. With the increase of hard segment content, the mechanical properties of the composites are enhanced. The results demonstrate that the mechanical properties of the TPU/GF composites are at their best when the isocyanate index is 1.01, the hard segment content is 43%, and the PBA molecular weight is 2000, with the stretching strength being 289.6 MPa, the impact strength being 141.8 KJ/mm2, the bending strength being 183.2 MPa, and the flexural modulus being 10.7 GPa.
- 30 April 2024
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 38 (2) , 435-450
Research on the performance of three-dimensional-braided-glass fiber reinforced in-situ polymerized TPU
In this study, thermoplastic polyurethane (TPU) is prepared by using 4,4′-methylenediphenyl diisocyanate (4,4′-MDI), poly (1,4-butylene adipate) (PBA), and butane-1,4-diol (BDO). PBA as soft segment for TPU. 4,4′- MDI and BDO as hard segment for TPU. The effects of isocyanate index, hard segment content, and soft segment molecular weight on TPU micro-phase separation, molecular weight, and thermal performance are investigated. 3D-Braided-Glass Fiber (GF) reinforced TPU composites are prepared by in-situ polymerized TPU as the matrix resin. Investigation is conducted into how the mechanical properties and microstructure of the composites are affected by the matrix resin TPU’s structural parameters. As the isocyanate index increases, the mechanical properties of the composites first enhance and then weaken, and the interface bonding between TPU and GF gradually deteriorates. Increasing the molecular weight of soft segments has the same trend of change. With the increase of hard segment content, the mechanical properties of the composites are enhanced. The results demonstrate that the mechanical properties of the TPU/GF composites are at their best when the isocyanate index is 1.01, the hard segment content is 43%, and the PBA molecular weight is 2000, with the stretching strength being 289.6 MPa, the impact strength being 141.8 KJ/mm2, the bending strength being 183.2 MPa, and the flexural modulus being 10.7 GPa.