AKAlexey Komolikov

Alexey Komolikov

*This is an algorithmically generated author record based on publicly available information.

Alexey Komolikov has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • METHOD OF EVALUATING QUALITY OF MIXING SOLUTIONS POLYMER COMPOSITES

    by Lipetsk State Technical University, Roman Li, Maria Kiba, Saint Petersburg Mining University, Yulia Li, Alexey Komolikov

    Known photometric methods for assessing the mixing quality of polymer composite solutions are unsuitable for monitoring polymer solutions filled with white particles. A new method for assessing the mixing quality of components in a polymer solution for filler particles of any color is proposed. This method is based on measuring the resistance of polymer composite solutions. The distribution of filler particles in the polymer solution, which correlates with the electrical resistance of the composite solution, is considered as an evaluation criterion for mixing quality. The method includes: measuring the electrical resistance of the polymer nanocomposite solution and calculating the specific volume electrical resistance; determining the average specific electrical resistance of the polymer nanocomposite solution and comparing it with the minimum rejection level on a calibration graph. It has been established that the electrical resistance of the composite solution will be maximum with a uniform distribution of dielectric particles throughout the solution. If these particles are unevenly distributed, or if aggregates occur, this will lead to current flow through the polymer solution and a decrease in electrical resistance. The electrical resistance of the composite solution will be significantly lower than with a uniform distribution. The opposite is true for a polymer solution filled with electrically conductive particles. It has been determined that the mixing quality is satisfactory if the following conditions are met: a) for dielectric particles, the average value of the measured specific volume electrical resistance should be no less than the minimum rejection level; b) for conductor particles, no greater than the minimum rejection level.

  • THERMOPHYSICAL PROPERTIES OF ELASTOMERIC NANOCOMPOSITE FILLED WITH CERAMIC NANOPARTICLES

    by Lipetsk State Technical University, Roman Li, Dmitry Psarev, Michurinsky State Agrarian University, Maria Kiba, Saint Petersburg Mining University, Alexey Komolikov

    Thermophysical properties of polymer fit in restored bearing units of automotive and tractor equipment are the most important characteristics determining its suitability for use under operating conditions. Metallic dispersed nanoparticles and carbon nanotubes used as fillers allow to significantly improve the thermophysical properties of elastomers and thermosets. Thermophysical properties of F-40S elastomer composites filled with ceramic nanoparticles in a volume fraction of 0.00156; 0.00311 and 0.00466 are studied in the work. The thermal conductivity coefficient increases by more than an order of magnitude: from 0.4 to 5.7 W/m‧K when filling the elastomer with ceramic nanoparticles in the optimal concentration (0.0031) The Burger formula is recommended for calculating the thermal conductivity of elastomers filled with ceramic nanoparticles, it is recommended The discrepancy between the calculated values of the thermal conductivity coefficient and the actual values does not exceed 2.5%. Filling the elastomer with ceramic nanoparticles increases the heat resistance of the material. The decrease in the strength of the nanocomposite after thermal aging is less intense than that of the elastomer: the aging coefficient for strength is 0.71, while that of the elastomer is 0.63. The effect of thermal aging on the change in deformation is similar: the aging coefficient for deformation of the composite is 0.37, and that of the elastomer is 0.31. Filling the elastomer with ceramic nanoparticles in the optimal concentration increases the thermal conductivity coefficient by 14.25 times. Aluminum oxide nanoparticles are inhibitors of thermal oxidation of butadiene-nitrile rubber SKN-40 and increase the thermal resistance of the F-40S elastomer: the aging coefficients for strength increase by 1.13 times, for deformation by 1.19 times.

  • MECHANICAL PROPERTIES OF F-40S ELASTOMER FILLED WITH CERAMIC NANOPARTICLES

    by Lipetsk State Technical University, Roman Li, Andrey Bykonya, Alexey Komolikov, Igor Lisovy

    Restoration of parts significantly reduces equipment repair costs and shortens its downtime. Polymer bearing fits allow to increase the service life of bearing units and housing parts many times after restoration; their durability can be increased by filling polymers with nanosized particles. In this work, the mechanical properties of F-40S elastomer composites filled with ceramic nanoparticles were studied, the optimal composition of the nanocomposite and the optimal mode of its heat treatment were determined. It was found that filling the elastomer with ceramic nanoparticles improves its mechanical properties. It was determined that filling the elastomer with ceramic nanoparticles increases the strength of the material to 18.0; 26.0 and 19.0 MPa with a nanoparticle content of 0.00156; 0.00311 and 0.00466, respectively. The maximum strength of nanocomposites during the studies increased up to 2.15 times, deformation of nanocomposites - up to 1.83 times, elastic modulus - up to 2.27; adhesion to the substrate - 1.4 times. It was found that the nanocomposite with a nanoparticle content of 0.00311 has the maximum values of strength, deformation and elastic modulus. With a further increase in the filler content, the indicators decrease, which is explained by the aggregation of nanoparticles. The optimal heat treatment mode was determined: temperature T = 150 0C, time t = 3 hours. In this case, the material has the highest specific work of destruction - 34.5 MJ / m3. Improvement of the mechanical properties of the elastomer after filling with ceramic nanoparticles confirms the promise of further comprehensive studies of the new material.

  • DESIGN AND PROCESS PARAMETERS OF TURBINE MIXER FOR MIXING OF POLYMER NANOCOMPOSITES SOLUTIONS

    by Lipetsk State Technical University, Roman Li, Dmitry Psarev, Michurinsky State Agrarian University, Alexey Komolikov, Igor Lisovy

    The permissible wear of bearing seats does not exceed 0.3 mm, therefore, when restoring with polymer composites, it is required to mix no more than 100 g of material at a time. The issue of mechanical mixing of such small volumes has not been considered previously and requires research. Devices with stirrers manufactured according to GOST 20680-200 cannot be used for mixing since they have excess vessel volume (more than 0.01 m3). A method has been developed for calculating the design and operating modes of a turbine stirrer when mixing a nanocomposite solution intended for restoring bearing seats. The article presents the design parameters of three mixing devices of different sizes. The technological mode of 3D printing of device parts and a turbine stirrer is described. A Flying Bear Ghost 5 3D printer is used, and PETG plastic is the consumable. An original composition of an elastomeric nanocomposite filled with non-metallic nanoparticles has been developed. The material has unique deformation and strength properties. The specific work of destruction of this nanocomposite is 2.54 times higher than that of elastomers filled with metal nanoparticles and 1.24 times higher than that of carbon nanotubes. An experiment was conducted that confirmed the applicability of the developed calculation program to solutions of elastomeric nanocomposites filled with non-metallic nanoparticles. High convergence of the calculated values of the optimal rotation frequency of the turbine mixer during mixing with the actual ones was established (the discrepancy is no more than 6%). The efficiency of mixing the nanocomposite solution was assessed by two criteria. The first criterion was the transmission coefficient. The value was determined after manual and mechanized mixing and compared. The second criterion was the strength of the nanocomposite samples after various mixing modes. The higher the quality of mixing, the greater the strength of the samples. The study showed the unsuitability of the first criterion. This is explained by the optical properties of the filler nanoparticles, which do not absorb but reflect the light flux.