Suho Park
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Suho Park has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
Jiyeon Jeon
Strategic Technology Research Institute Korea Research Institute of Standards and Science Daejeon 34113 Republic of Korea
4 shared publications- Sang Jun Lee
Korea Research Institute of Standards and Science, Daejeon, Republic of Korea
4 shared publications - Byong Sun Chun
Korea Research Institute of Standards and Science, Daejeon 34113, Republic of Korea
3 shared publications Yeongho Kim
School of Materials Science and Engineering Chonnam National University Gwangju 61186 Republic of Korea
3 shared publicationsDavid J. Smith
Department of Physics Arizona State University Tempe AZ 85287 USA
2 shared publicationsMartha R. McCartney
Department of Physics Arizona State University Tempe AZ 85287 USA
2 shared publications
Latest Publications
- Open Access
- 26 May 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (2)
SiGeSn-on-insulator platform enabled by a novel layer-transfer process technology
Neuromorphic computing based on computing-in-memory architectures requires device platforms capable of high-density integration, low power consumption, and precise analog weight modulation. Memtransistors, which integrate memristive and transistor functionalities within a single device, offer a hardware-efficient route toward compact artificial synapses. Among candidate channel materials, SiGeSn alloys provide unique advantages due to Sn-induced bandgap and strain engineering, mobility enhancement, and electrically tunable defect and short-range order (SRO) effects that enable nonvolatile analog conductance modulation. However, epitaxial growth of SiGeSn is challenged by low Sn solubility and lattice mismatch, necessitating Ge virtual substrates that introduce strain, which complicates intrinsic material characterizations, and leakage, which degrades device performance. Here, we developed a dual-layer epitaxial lift-off process to achieve large-area transfer of 44-nm Si0.08Ge0.85Sn0.07 nanoribbons, enabling strain-relaxed SiGeSn-on-insulator structures with smooth interfaces (RMS ∼0.76 nm) and void-free van der Waals bonding. The process exploits the high etching selectivity between Si and Ge in tetramethylammonium hydroxide, with the Ge buffer serving as an etch stop and subsequently removed through Raman-monitored etching. This approach yields clean SiGeSn-on-insulator structures without thermal or chemical degradation and effectively eliminates substrate-induced strain. Back-gated nanoribbon transistors exhibit ON/OFF ratios up to 1.82 × 103 and a peak hole mobility of 13.5 cm2/V s. With this platform, the investigation of SRO effects on electronic properties is enabled. Additionally, the capability of transferring the ribbons on arbitrary substrates enables its accurate material characterization and provides a scalable pathway for high-performance SiGeSn-based neuromorphic device applications.
- 26 May 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (2)
Open AccessSiGeSn-on-insulator platform enabled by a novel layer-transfer process technology
Neuromorphic computing based on computing-in-memory architectures requires device platforms capable of high-density integration, low power consumption, and precise analog weight modulation. Memtransistors, which integrate memristive and transistor functionalities within a single device, offer a hardware-efficient route toward compact artificial synapses. Among candidate channel materials, SiGeSn alloys provide unique advantages due to Sn-induced bandgap and strain engineering, mobility enhancement, and electrically tunable defect and short-range order (SRO) effects that enable nonvolatile analog conductance modulation. However, epitaxial growth of SiGeSn is challenged by low Sn solubility and lattice mismatch, necessitating Ge virtual substrates that introduce strain, which complicates intrinsic material characterizations, and leakage, which degrades device performance. Here, we developed a dual-layer epitaxial lift-off process to achieve large-area transfer of 44-nm Si0.08Ge0.85Sn0.07 nanoribbons, enabling strain-relaxed SiGeSn-on-insulator structures with smooth interfaces (RMS ∼0.76 nm) and void-free van der Waals bonding. The process exploits the high etching selectivity between Si and Ge in tetramethylammonium hydroxide, with the Ge buffer serving as an etch stop and subsequently removed through Raman-monitored etching. This approach yields clean SiGeSn-on-insulator structures without thermal or chemical degradation and effectively eliminates substrate-induced strain. Back-gated nanoribbon transistors exhibit ON/OFF ratios up to 1.82 × 103 and a peak hole mobility of 13.5 cm2/V s. With this platform, the investigation of SRO effects on electronic properties is enabled. Additionally, the capability of transferring the ribbons on arbitrary substrates enables its accurate material characterization and provides a scalable pathway for high-performance SiGeSn-based neuromorphic device applications.
- 3 June 2025
- Published by Wiley in Advanced Materials Technologies
- Vol. 10 (17)
Uncooled GeSn MWIR Photodetectors Using Fully Relaxed Thin Triple‐Step Buffer
GeSn photodetectors monolithically grown on Ge virtual substrates demonstrate mid‐wave infrared (MWIR) detection at room temperature. The lattice mismatch between GeSn and Ge causes dislocations and compressive strain, creating leakage pathways and unwanted indirect band transitions. Designed thin Ge0.91Sn0.09 triple‐step buffer layers of ≈175 nm total thickness reduce dislocations and enable full relaxation, showing 100% lattice relaxation and smooth surface roughness of 0.83 nm with shorter auto‐correlation length in surface morphology compared to single‐step buffers. Ge1‐xSnx photodetectors (x = 0.09, 0.12, and 0.15) on triple‐step buffers with n‐i‐p configurations achieve lattice strain relaxations of 99%, 88%, and 80%, respectively. Ge0.91Sn0.09 and Ge0.88Sn0.12 show gradual variation in auto‐correlation amplitude, while Ge0.85Sn0.15 shows an increase due to lattice mismatch. Shockley–Read–Hall recombination current dominates at low reverse bias due to mismatch‐induced dislocations, while band‐to‐band tunneling current dominates at higher reverse bias due to narrowing bandgap under strong electric fields. The photodetectors show extended spectral response with increasing Sn composition of i‐GeSn active layer sandwiched by barriers. Ge0.88Sn0.12 and Ge0.85Sn0.15 exhibit extended wavelength cut‐offs of 3.12 and 3.27 µm at room temperature, demonstrating significant potential for silicon‐based MWIR applications.
- 3 June 2025
- Published by Wiley in Advanced Materials Technologies
- Vol. 10 (17)
Uncooled GeSn MWIR Photodetectors Using Fully Relaxed Thin Triple‐Step Buffer
GeSn photodetectors monolithically grown on Ge virtual substrates demonstrate mid‐wave infrared (MWIR) detection at room temperature. The lattice mismatch between GeSn and Ge causes dislocations and compressive strain, creating leakage pathways and unwanted indirect band transitions. Designed thin Ge0.91Sn0.09 triple‐step buffer layers of ≈175 nm total thickness reduce dislocations and enable full relaxation, showing 100% lattice relaxation and smooth surface roughness of 0.83 nm with shorter auto‐correlation length in surface morphology compared to single‐step buffers. Ge1‐xSnx photodetectors (x = 0.09, 0.12, and 0.15) on triple‐step buffers with n‐i‐p configurations achieve lattice strain relaxations of 99%, 88%, and 80%, respectively. Ge0.91Sn0.09 and Ge0.88Sn0.12 show gradual variation in auto‐correlation amplitude, while Ge0.85Sn0.15 shows an increase due to lattice mismatch. Shockley–Read–Hall recombination current dominates at low reverse bias due to mismatch‐induced dislocations, while band‐to‐band tunneling current dominates at higher reverse bias due to narrowing bandgap under strong electric fields. The photodetectors show extended spectral response with increasing Sn composition of i‐GeSn active layer sandwiched by barriers. Ge0.88Sn0.12 and Ge0.85Sn0.15 exhibit extended wavelength cut‐offs of 3.12 and 3.27 µm at room temperature, demonstrating significant potential for silicon‐based MWIR applications.
- Open Access
- 1 October 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (10)
InP-based strain engineered InAs(Sb)/InAsPSb multiple quantum wells with tunable emission and high internal quantum efficiency enabled by Sb incorporation
A type I InAs(Sb)/InAsPSb strain engineered multiple quantum wells light emitting diodes system has been demonstrated. Tensile InAsPSb quantum barriers with a high degree of band offset (∆EC = 116–123 meV, ∆EV = 193–250 meV) were used to compensate for the high compressive strain of the InAs(Sb) quantum wells. The structure was grown on the n+-InAsxP1−x metamorphic buffer with a high degree of relaxation (98%), low surface roughness (0.69 nm), and low dislocation density. Through careful strain engineering design, the compressive strain of InAs(Sb) reaches 0.57%–1.52% without strain relaxation. The incorporation of Sb into the multiple quantum wells not only reduces the bandgap but also improves the interface quality by acting as an effective surfactant. Structural analysis reveals superior quality in InAsSb/InAsPSb multiple quantum wells compared to InAs/InAsPSb multiple quantum wells, demonstrating significantly reduced interface roughness and suppression of the Stranski–Krastanov growth mode. Room temperature electroluminescence measurements show a tunable emission wavelength ranging from 2.7 to 3.3 μm, accompanied by a narrow full width at half maximum value of 45 meV. Photoluminescence analysis indicates that the internal quantum efficiency of InAsSb/InAsPSb multiple quantum wells is 5.5%, which is 7 times higher than that of InAs/InAsPSb.
- 1 October 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (10)
Open AccessInP-based strain engineered InAs(Sb)/InAsPSb multiple quantum wells with tunable emission and high internal quantum efficiency enabled by Sb incorporation
A type I InAs(Sb)/InAsPSb strain engineered multiple quantum wells light emitting diodes system has been demonstrated. Tensile InAsPSb quantum barriers with a high degree of band offset (∆EC = 116–123 meV, ∆EV = 193–250 meV) were used to compensate for the high compressive strain of the InAs(Sb) quantum wells. The structure was grown on the n+-InAsxP1−x metamorphic buffer with a high degree of relaxation (98%), low surface roughness (0.69 nm), and low dislocation density. Through careful strain engineering design, the compressive strain of InAs(Sb) reaches 0.57%–1.52% without strain relaxation. The incorporation of Sb into the multiple quantum wells not only reduces the bandgap but also improves the interface quality by acting as an effective surfactant. Structural analysis reveals superior quality in InAsSb/InAsPSb multiple quantum wells compared to InAs/InAsPSb multiple quantum wells, demonstrating significantly reduced interface roughness and suppression of the Stranski–Krastanov growth mode. Room temperature electroluminescence measurements show a tunable emission wavelength ranging from 2.7 to 3.3 μm, accompanied by a narrow full width at half maximum value of 45 meV. Photoluminescence analysis indicates that the internal quantum efficiency of InAsSb/InAsPSb multiple quantum wells is 5.5%, which is 7 times higher than that of InAs/InAsPSb.
- Open Access
- 19 September 2024
- Published by Wiley in Small Structures
- Vol. 6 (2)
High‐Efficiency Flexible GaAs/InGaAs Dual‐Junction Solar Cells Fabricated by Metallic Nanoparticle‐Based Wafer Bonding
Multijunction solar cells made from highly lattice‐mismatched (LMM) material systems offer an optimal bandgap combination for the ultrahigh conversion of solar energy to electricity. Conventional fabrication techniques for multijunction cells, such as metamorphic epitaxy, direct wafer bonding, and adhesive wafer bonding, are still expensive and produce low yields owing to the use of complex process steps and sophisticated equipment. Herein, flexible GaAs/In0.53Ga0.47As dual‐junction solar cells with a large lattice mismatch of 3.7% between the subcells are fabricated using an indium‐tin‐oxide (ITO) nanoparticle‐based wafer bonding process. The ITO bonding layer electrically and optically connecting the GaAs top and InGaAs bottom cells shows a low series resistance of 5.7 × 10−2 Ω cm−2 and a high optical transmission of 90% in the infrared range of 870–1800 nm. The dark current characteristic of the ITO‐bonded dual‐junction cell exhibits a good rectifying behavior with a high on–off ratio of ≈105 at ±2 V. Under 1 sun AM 1.5G illumination, a high power conversion efficiency of 28.5% is achieved for the two‐terminal series‐connected dual‐junction cell, with an average external radiative efficiency of 2.6%. In these findings, it is suggested that ITO nanoparticle‐based wafer bonding may be a facile and cost‐effective route for fabricating LMM solar cells, potentially overcoming the Shockley–Queisser efficiency limit.
- 19 September 2024
- Published by Wiley in Small Structures
- Vol. 6 (2)
Open AccessHigh‐Efficiency Flexible GaAs/InGaAs Dual‐Junction Solar Cells Fabricated by Metallic Nanoparticle‐Based Wafer Bonding
Multijunction solar cells made from highly lattice‐mismatched (LMM) material systems offer an optimal bandgap combination for the ultrahigh conversion of solar energy to electricity. Conventional fabrication techniques for multijunction cells, such as metamorphic epitaxy, direct wafer bonding, and adhesive wafer bonding, are still expensive and produce low yields owing to the use of complex process steps and sophisticated equipment. Herein, flexible GaAs/In0.53Ga0.47As dual‐junction solar cells with a large lattice mismatch of 3.7% between the subcells are fabricated using an indium‐tin‐oxide (ITO) nanoparticle‐based wafer bonding process. The ITO bonding layer electrically and optically connecting the GaAs top and InGaAs bottom cells shows a low series resistance of 5.7 × 10−2 Ω cm−2 and a high optical transmission of 90% in the infrared range of 870–1800 nm. The dark current characteristic of the ITO‐bonded dual‐junction cell exhibits a good rectifying behavior with a high on–off ratio of ≈105 at ±2 V. Under 1 sun AM 1.5G illumination, a high power conversion efficiency of 28.5% is achieved for the two‐terminal series‐connected dual‐junction cell, with an average external radiative efficiency of 2.6%. In these findings, it is suggested that ITO nanoparticle‐based wafer bonding may be a facile and cost‐effective route for fabricating LMM solar cells, potentially overcoming the Shockley–Queisser efficiency limit.
- Open Access
- 28 August 2024
- Published by Wiley in Advanced Functional Materials
- Vol. 34 (45)
Metamorphic InGaAs/InAsPSb Quantum Well Light Emitting Diodes for Operation in the Short‐Wave Infrared Region
Solid‐state infrared sources designed to emit wavelengths above 2 µm often face challenges in achieving high emission efficiency, minimizing power consumption, and reducing fabrication costs. In response, a 2.4 µm wavelength light emitting diode (LED) is developed using metamorphic In0.83Ga0.17As/InAs0.3P0.65Sb0.05 multiple quantum well (MQW) heterostructures. The substantial conduction (94 meV) and valence band offsets (300 meV) within this type‐I MQW LED architecture result in strong carrier confinement, improving electron and hole wavefunction overlap. Despite a notable lattice mismatch of 2.0% between the MQWs and InP substrate, the resulting LED wafer exhibits exceptionally low surface roughness (1.1 nm) and well‐defined, sharp interfaces within the heterostructures. Furthermore, this MQW LED exhibits favorable emission properties, including a low turn‐on field, minimal efficiency droop, and stable emission wavelength across varying injection currents. These advancements underscore the potential of such short‐wave infrared emitters for scalable applications in fields such as inspection, optical on‐chip communication, and biomedical diagnostics.
- 28 August 2024
- Published by Wiley in Advanced Functional Materials
- Vol. 34 (45)
Open AccessMetamorphic InGaAs/InAsPSb Quantum Well Light Emitting Diodes for Operation in the Short‐Wave Infrared Region
Solid‐state infrared sources designed to emit wavelengths above 2 µm often face challenges in achieving high emission efficiency, minimizing power consumption, and reducing fabrication costs. In response, a 2.4 µm wavelength light emitting diode (LED) is developed using metamorphic In0.83Ga0.17As/InAs0.3P0.65Sb0.05 multiple quantum well (MQW) heterostructures. The substantial conduction (94 meV) and valence band offsets (300 meV) within this type‐I MQW LED architecture result in strong carrier confinement, improving electron and hole wavefunction overlap. Despite a notable lattice mismatch of 2.0% between the MQWs and InP substrate, the resulting LED wafer exhibits exceptionally low surface roughness (1.1 nm) and well‐defined, sharp interfaces within the heterostructures. Furthermore, this MQW LED exhibits favorable emission properties, including a low turn‐on field, minimal efficiency droop, and stable emission wavelength across varying injection currents. These advancements underscore the potential of such short‐wave infrared emitters for scalable applications in fields such as inspection, optical on‐chip communication, and biomedical diagnostics.
- Open Access
- 25 August 2023
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 11 (37) , 12698-12706
Chip-scale short-wavelength infrared InGaAs microspectrometer based on a linear variable optical filter
An extended short-wavelength infrared microspectrometer by monolithic integrarion of a 256 × 1 InGaAs linear array detector with a wedge-shaped Si/SiO2 Fabry-Perot linear variable optical filter.
- 25 August 2023
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 11 (37) , 12698-12706
Open AccessChip-scale short-wavelength infrared InGaAs microspectrometer based on a linear variable optical filter
An extended short-wavelength infrared microspectrometer by monolithic integrarion of a 256 × 1 InGaAs linear array detector with a wedge-shaped Si/SiO2 Fabry-Perot linear variable optical filter.
- 26 May 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 10 (24) , 13106-13113
Inverted metamorphic InGaAsP/InGaAs dual-junction solar cells towards full solar spectrum harvesting
An InGaAsP (1.04 eV)/InGaAs (0.54 eV) dual-junction solar cell, monolithically grown in an inverted configuration on an InP substrate, has been demonstrated. Five metamorphic compositionally graded buffers of InAsxP1−x are used to transition from the InP lattice constant to that of the In0.74Ga0.26As bottom cell. The InAs0.45P0.55 buffer, lattice-matched to In0.74Ga0.26As, has a surface crosshatch pattern with an rms roughness of 2.1 and 4.7 nm along the in-plane [110] and [10] directions, respectively, due to different lateral growth rates under high As pressure. Cross-section observations using transmission electron microscopy indicate a major reduction in the density of misfit and threading dislocations across the metamorphic InAsxP1−x structure. The formation of crystalline defects in the n+-InAsP buffers induces a strain relaxation of ∼95% in the bottom cell with a relaxed lattice constant of 5.9563 Å. The reverse saturation current and ideality factor of the bottom cell are increased because of enhanced nonradiative recombination at threading dislocations with a density of 2 × 106 cm−2. Under AM 1.5G illumination, the dual-junction solar cell with extended absorption wavelengths up to 2400 nm has a photovoltaic conversion efficiency of 5.49% with an open-circuit voltage of 0.70 V, a short-circuit current density of 9.86 mA cm−2, and a fill factor of 80.12%.
- 26 May 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 10 (24) , 13106-13113
Inverted metamorphic InGaAsP/InGaAs dual-junction solar cells towards full solar spectrum harvesting
An InGaAsP (1.04 eV)/InGaAs (0.54 eV) dual-junction solar cell, monolithically grown in an inverted configuration on an InP substrate, has been demonstrated. Five metamorphic compositionally graded buffers of InAsxP1−x are used to transition from the InP lattice constant to that of the In0.74Ga0.26As bottom cell. The InAs0.45P0.55 buffer, lattice-matched to In0.74Ga0.26As, has a surface crosshatch pattern with an rms roughness of 2.1 and 4.7 nm along the in-plane [110] and [10] directions, respectively, due to different lateral growth rates under high As pressure. Cross-section observations using transmission electron microscopy indicate a major reduction in the density of misfit and threading dislocations across the metamorphic InAsxP1−x structure. The formation of crystalline defects in the n+-InAsP buffers induces a strain relaxation of ∼95% in the bottom cell with a relaxed lattice constant of 5.9563 Å. The reverse saturation current and ideality factor of the bottom cell are increased because of enhanced nonradiative recombination at threading dislocations with a density of 2 × 106 cm−2. Under AM 1.5G illumination, the dual-junction solar cell with extended absorption wavelengths up to 2400 nm has a photovoltaic conversion efficiency of 5.49% with an open-circuit voltage of 0.70 V, a short-circuit current density of 9.86 mA cm−2, and a fill factor of 80.12%.