Yaroslav Naumov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yaroslav Naumov has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Viktoriia Melnyk-Shamrai
Zhytomyr Polytechnic State University
2 shared publications - Volodymyr Shamrai
Zhytomyr Polytechnic State University
2 shared publications - Ірина Володимирівна Леонець
Zhytomyr Polytech State Univ, Zhytomyr, Ukraine
2 shared publications - Володимир Володимирович Котенко
Державний університет «Житомирська політехніка», Україна
2 shared publications - Iryna Patseva
Zhytomyr Polytechnic State University
1 shared publication Maryna Kunytska
1 shared publication
Latest Publications
- 1 January 2026
- Published by Donetsk National Technical University in Naukovyi visnyk Donetskoho natsionalnoho tekhnichnoho universytetu
- Vol. 2 (17)
DYNAMICS OF PRODUCTION, INVESTMENT, AND ENTREPRENEURIAL ACTIVITY IN THE DECORATIVE STONE EXTRACTION INDUSTRY IN UKRAINE
Purpose. The purpose of the study is to identify and comprehensively analyze trends in the development of the decorative stone extraction industry in Ukraine through an assessment of production dynamics, capital investment, and entrepreneurial activity, as well as to determine the key factors shaping the functioning, adaptation, and recovery of the industry under conditions of macroeconomic instability, regional concentration of production, and wartime challenges. Methodology. The study employs statistical-economic, comparative, structural, and regional analysis. This methodological approach made it possible to trace changes in the number of business entities, the volume of produced and sold output, capital investment, and to identify the territorial concentration of enterprises in the industry. Results. It has been established that in 2014–2023 the decorative stone extraction industry in Ukraine developed unevenly under the influence of crisis-related macroeconomic and wartime factors; however, it retained the capacity for adaptation and recovery. A reduction in the number of active business entities was identified, alongside a partial revival of entrepreneurial activity in 2023. The study demonstrates growth in production volumes over the long term, the cyclical nature of investment activity, and the dominance of investment in machinery and equipment. It was determined that Zhytomyr region is the main territorial center of the industry, while external demand for natural stone products supports its development prospects. Scientific novelty consists in the comprehensive integration of the analysis of production dynamics, capital investment, and entrepreneurial activity in the decorative stone extraction industry at both the national and regional levels, which made it possible to identify patterns in its functioning and recovery under conditions of wartime risks and economic instability. Practical significance of the obtained results lies in the possibility of using the formulated conclusions to substantiate directions for production modernization, improvement of sectoral policy, expansion of access to investment resources, development of export orientation, and enhancement of the competitiveness of enterprises in Ukraine’s stone extraction industry Key words: decorative stone, stone extraction, capital investment, entrepreneurial activity.
- 1 January 2026
- Published by Donetsk National Technical University in Naukovyi visnyk Donetskoho natsionalnoho tekhnichnoho universytetu
- Vol. 2 (17)
DYNAMICS OF PRODUCTION, INVESTMENT, AND ENTREPRENEURIAL ACTIVITY IN THE DECORATIVE STONE EXTRACTION INDUSTRY IN UKRAINE
Purpose. The purpose of the study is to identify and comprehensively analyze trends in the development of the decorative stone extraction industry in Ukraine through an assessment of production dynamics, capital investment, and entrepreneurial activity, as well as to determine the key factors shaping the functioning, adaptation, and recovery of the industry under conditions of macroeconomic instability, regional concentration of production, and wartime challenges. Methodology. The study employs statistical-economic, comparative, structural, and regional analysis. This methodological approach made it possible to trace changes in the number of business entities, the volume of produced and sold output, capital investment, and to identify the territorial concentration of enterprises in the industry. Results. It has been established that in 2014–2023 the decorative stone extraction industry in Ukraine developed unevenly under the influence of crisis-related macroeconomic and wartime factors; however, it retained the capacity for adaptation and recovery. A reduction in the number of active business entities was identified, alongside a partial revival of entrepreneurial activity in 2023. The study demonstrates growth in production volumes over the long term, the cyclical nature of investment activity, and the dominance of investment in machinery and equipment. It was determined that Zhytomyr region is the main territorial center of the industry, while external demand for natural stone products supports its development prospects. Scientific novelty consists in the comprehensive integration of the analysis of production dynamics, capital investment, and entrepreneurial activity in the decorative stone extraction industry at both the national and regional levels, which made it possible to identify patterns in its functioning and recovery under conditions of wartime risks and economic instability. Practical significance of the obtained results lies in the possibility of using the formulated conclusions to substantiate directions for production modernization, improvement of sectoral policy, expansion of access to investment resources, development of export orientation, and enhancement of the competitiveness of enterprises in Ukraine’s stone extraction industry Key words: decorative stone, stone extraction, capital investment, entrepreneurial activity.
- Open Access
- 16 December 2025
- Published by Zhytomyr Polytechnic State University in Технічна інженерія
- No. 2(96),p. 244-251
Стан і тенденції використання вапнякової сировини в Україні у 2011–2023 роках із визначенням стратегічних орієнтирів відбудови
Актуальність представленого дослідження зумовлена значною роллю видобувної промисловості в Україні за обсягами видобутку природного вапнякового каменю. Метою роботи є огляд тенденцій розвитку видобутку та експорту вапняку, оцінка економічного впливу галузі на регіональний розвиток, а також ідентифікація основних викликів і розробка стратегічних заходів щодо підвищення її конкурентоспроможності. Результати роботи засвідчують, що галузь зіткнулася з низкою проблем, серед яких екологічні обмеження, відсутність великих родовищ та мала кількість якісної вапнякової сировини. Перспективою подальших досліджень є впровадження екологічних технологій та оптимізація логістичних маршрутів, вкладення коштів у пошук та розвідку родовищ, що підвищить стійкість галузі до глобальних економічних коливань та посилить її економічний вплив на територію України.
- 16 December 2025
- Published by Zhytomyr Polytechnic State University in Технічна інженерія
- No. 2(96),p. 244-251
Open AccessСтан і тенденції використання вапнякової сировини в Україні у 2011–2023 роках із визначенням стратегічних орієнтирів відбудови
Актуальність представленого дослідження зумовлена значною роллю видобувної промисловості в Україні за обсягами видобутку природного вапнякового каменю. Метою роботи є огляд тенденцій розвитку видобутку та експорту вапняку, оцінка економічного впливу галузі на регіональний розвиток, а також ідентифікація основних викликів і розробка стратегічних заходів щодо підвищення її конкурентоспроможності. Результати роботи засвідчують, що галузь зіткнулася з низкою проблем, серед яких екологічні обмеження, відсутність великих родовищ та мала кількість якісної вапнякової сировини. Перспективою подальших досліджень є впровадження екологічних технологій та оптимізація логістичних маршрутів, вкладення коштів у пошук та розвідку родовищ, що підвищить стійкість галузі до глобальних економічних коливань та посилить її економічний вплив на територію України.
- Open Access
- 16 December 2025
- Published by Zhytomyr Polytechnic State University in Технічна інженерія
- No. 2(96),p. 339-345
Кількісна оцінка відходів при розпилюванні природного каменю дисковими пилами
У статті представлено комплексну кількісну оцінку утворення відходів при розпилюванні блоків природного каменю дисковими пилами, що є актуальним завданням для каменеобробної галузі. Дослідження вирішує науково-практичну проблему, що полягає у значній розбіжності між теоретичними розрахунками та фактичними обсягами втрат сировини на виробництві. Ця розбіжність призводить не лише до прямих економічних збитків через втрату дорогоцінного матеріалу, але й ускладнює виробниче планування та калькуляцію собівартості продукції. Дослідженням підтверджено зворотну залежність між товщиною слябів та відсотком відходів. Практичні показники втрат, отримані в ході експерименту, значно перевищують ідеальні розрахункові значення. Наприклад, при розпилюванні на сляби товщиною 20 мм фактичні втрати сягають 51,41 %, тоді як теоретичний розрахунок прогнозує лише 34 %. Встановлено, що ключовою причиною такої різниці є подвійна природа відходів: крім технологічного шламу, що є неминучим наслідком роботи різального інструменту, утворюються геометричні відходи («обапол») через неправильну форму сировинних блоків. Аналіз 29 окремих блоків показав, що висока варіативність фактичних втрат (від 34 до 54 %) зумовлена переважно індивідуальною геометрією кожного блоку, що робить узагальнені розрахунки недостатньо точними для практичного застосування. Головним результатом роботи є розроблена чотириетапна методика кількісної оцінки відходів, що дозволяє подолати обмеження існуючих підходів. Вона містить вхідний контроль із визначенням нетто- та брутто-об’ємів для попередньої оцінки геометричних втрат; теоретичне моделювання для розрахунку ідеального об’єму шламу; емпіричний аналіз для складання фактичного матеріального балансу після розпилювання; введення емпіричного коефіцієнта коригування (К). Цей коефіцієнт враховує неідеальності реального виробничого процесу (вібрації, знос інструменту тощо) і дозволяє створити вдосконалену прогностичну модель. Таким чином, запропонована методика перетворює оцінку відходів зі статичної констатації втрат на дієвий інструмент для економічно обґрунтованого планування, точного прогнозування та оптимізації технологічних процесів у каменеобробній галузі.
- 16 December 2025
- Published by Zhytomyr Polytechnic State University in Технічна інженерія
- No. 2(96),p. 339-345
Open AccessКількісна оцінка відходів при розпилюванні природного каменю дисковими пилами
У статті представлено комплексну кількісну оцінку утворення відходів при розпилюванні блоків природного каменю дисковими пилами, що є актуальним завданням для каменеобробної галузі. Дослідження вирішує науково-практичну проблему, що полягає у значній розбіжності між теоретичними розрахунками та фактичними обсягами втрат сировини на виробництві. Ця розбіжність призводить не лише до прямих економічних збитків через втрату дорогоцінного матеріалу, але й ускладнює виробниче планування та калькуляцію собівартості продукції. Дослідженням підтверджено зворотну залежність між товщиною слябів та відсотком відходів. Практичні показники втрат, отримані в ході експерименту, значно перевищують ідеальні розрахункові значення. Наприклад, при розпилюванні на сляби товщиною 20 мм фактичні втрати сягають 51,41 %, тоді як теоретичний розрахунок прогнозує лише 34 %. Встановлено, що ключовою причиною такої різниці є подвійна природа відходів: крім технологічного шламу, що є неминучим наслідком роботи різального інструменту, утворюються геометричні відходи («обапол») через неправильну форму сировинних блоків. Аналіз 29 окремих блоків показав, що висока варіативність фактичних втрат (від 34 до 54 %) зумовлена переважно індивідуальною геометрією кожного блоку, що робить узагальнені розрахунки недостатньо точними для практичного застосування. Головним результатом роботи є розроблена чотириетапна методика кількісної оцінки відходів, що дозволяє подолати обмеження існуючих підходів. Вона містить вхідний контроль із визначенням нетто- та брутто-об’ємів для попередньої оцінки геометричних втрат; теоретичне моделювання для розрахунку ідеального об’єму шламу; емпіричний аналіз для складання фактичного матеріального балансу після розпилювання; введення емпіричного коефіцієнта коригування (К). Цей коефіцієнт враховує неідеальності реального виробничого процесу (вібрації, знос інструменту тощо) і дозволяє створити вдосконалену прогностичну модель. Таким чином, запропонована методика перетворює оцінку відходів зі статичної констатації втрат на дієвий інструмент для економічно обґрунтованого планування, точного прогнозування та оптимізації технологічних процесів у каменеобробній галузі.
- Open Access
- 31 October 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (6 (137)) , 41-48
Development of geopolymer concrete formulations based on activated stone processing sludge to reduce natural resource consumption
This study investigates concrete mixtures modified by partial or complete replacement of cement and sand with granite and gabbro sludge from stone-processing plants, activated with a 12M NaOH solution to improve their mechanical properties and microstructure. The task addressed relates to the excessive accumulation of sludge waste from the stone-processing industry, which pollutes the environment and predetermines the need to reduce the consumption of natural resources (cement and sand) in concrete production. This production is accompanied by high CO2 emissions and significant costs. All these factors necessitate designing environmentally friendly and economically viable construction materials. The study investigated the effect of replacing cement (0–100%) and sand (0–100%) with a mixture of granite and gabbro sludge on compressive strength and ultrasonic pulse velocity after 7, 14, and 28 days of curing. Replacing up to 30% of sand provides a compressive strength of 45–50 MPa while replacing up to 20% of cement provides 30–32 MPa on day 28, meeting structural requirements (>10 MPa). The ultrasonic velocity (4200–4300 m/s at 30% sand replacement and 3800–4000 m/s at 20% cement replacement) indicates the preservation of a dense structure. Distinguishing features of the results are attributed to the combination of granite and gabbro sludge activated with NaOH that produces a microfiller effect and enables pozzolanic activity. This makes it possible to reduce sand consumption by 30% and cement by 20% without a significant loss of strength. Unlike conventional mixtures or solutions using only one type of sludge, strength reduction proceeds more slowly due to fewer microcracks. The results are suitable for producing environmentally friendly concrete for road and residential construction under moderately aggressive environmental conditions. The optimal replacement (30% sand or 20% cement) is effective under both laboratory and industrial conditions, provided that the sludge has a homogeneous composition and is activated with NaOH
- 31 October 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (6 (137)) , 41-48
Open AccessDevelopment of geopolymer concrete formulations based on activated stone processing sludge to reduce natural resource consumption
This study investigates concrete mixtures modified by partial or complete replacement of cement and sand with granite and gabbro sludge from stone-processing plants, activated with a 12M NaOH solution to improve their mechanical properties and microstructure. The task addressed relates to the excessive accumulation of sludge waste from the stone-processing industry, which pollutes the environment and predetermines the need to reduce the consumption of natural resources (cement and sand) in concrete production. This production is accompanied by high CO2 emissions and significant costs. All these factors necessitate designing environmentally friendly and economically viable construction materials. The study investigated the effect of replacing cement (0–100%) and sand (0–100%) with a mixture of granite and gabbro sludge on compressive strength and ultrasonic pulse velocity after 7, 14, and 28 days of curing. Replacing up to 30% of sand provides a compressive strength of 45–50 MPa while replacing up to 20% of cement provides 30–32 MPa on day 28, meeting structural requirements (>10 MPa). The ultrasonic velocity (4200–4300 m/s at 30% sand replacement and 3800–4000 m/s at 20% cement replacement) indicates the preservation of a dense structure. Distinguishing features of the results are attributed to the combination of granite and gabbro sludge activated with NaOH that produces a microfiller effect and enables pozzolanic activity. This makes it possible to reduce sand consumption by 30% and cement by 20% without a significant loss of strength. Unlike conventional mixtures or solutions using only one type of sludge, strength reduction proceeds more slowly due to fewer microcracks. The results are suitable for producing environmentally friendly concrete for road and residential construction under moderately aggressive environmental conditions. The optimal replacement (30% sand or 20% cement) is effective under both laboratory and industrial conditions, provided that the sludge has a homogeneous composition and is activated with NaOH
- 30 December 2024
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 18 (4) , 10-17
Reuse of stone working enterprise slurry in geopolymer and concrete products
Purpose is to assess influence by fine stone working refuse (FSWR) on physicomechanical characteristics of geopolymer and concrete materials for future development of efficient methods of the FSWR reuse. Methods. Geopolymer mixtures and concrete samples differing in FSWR proportions were applied for the research. Mechanical compression testing was performed with the samples, which helped assess influence by different number of FSWR on material strength. Totally, 16 polymer and 18 concrete samples were prepared. Findings. The research has analyzed the possibility of FSWR application while manufacturing concrete and geopolymer materials to reuse industrial waste, and mitigate its environmental impact. The research is intended to identify FSWR effect on physicomechanical characteristics of materials, and develop techniques for their reuse. FSWR addition loses geopolymer strength: if content is 25% then strength is 20 MPa; if the content is 50% then strength drops down to 5.3 MPa. As for concrete, partial sand replacement by FSWR decreases strength insignificantly (from 37.42 to 36.6 MPa if FSWR content is 20%). Geopolymers with 25% of FSWR are suitable for low-load structures; in turn, concrete mixtures containing FSWR can be applied without significant strength decrease. Originality. . For the first time, optimal fine refuse concentration of strong natural stone from Zhytomyr Region has been identified. The concentration is up to 25%. It provides acceptable compression strength with no significant decrease in technical characteristics. Practical implications are as follows. Compliance with optimal FSWR proportions in composition of geopolymer and concrete mixtures makes it possible to reduce cost of raw materials; decrease FSWR amount; and support the closed economy principles in the construction industry.
- 30 December 2024
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 18 (4) , 10-17
Reuse of stone working enterprise slurry in geopolymer and concrete products
Purpose is to assess influence by fine stone working refuse (FSWR) on physicomechanical characteristics of geopolymer and concrete materials for future development of efficient methods of the FSWR reuse. Methods. Geopolymer mixtures and concrete samples differing in FSWR proportions were applied for the research. Mechanical compression testing was performed with the samples, which helped assess influence by different number of FSWR on material strength. Totally, 16 polymer and 18 concrete samples were prepared. Findings. The research has analyzed the possibility of FSWR application while manufacturing concrete and geopolymer materials to reuse industrial waste, and mitigate its environmental impact. The research is intended to identify FSWR effect on physicomechanical characteristics of materials, and develop techniques for their reuse. FSWR addition loses geopolymer strength: if content is 25% then strength is 20 MPa; if the content is 50% then strength drops down to 5.3 MPa. As for concrete, partial sand replacement by FSWR decreases strength insignificantly (from 37.42 to 36.6 MPa if FSWR content is 20%). Geopolymers with 25% of FSWR are suitable for low-load structures; in turn, concrete mixtures containing FSWR can be applied without significant strength decrease. Originality. . For the first time, optimal fine refuse concentration of strong natural stone from Zhytomyr Region has been identified. The concentration is up to 25%. It provides acceptable compression strength with no significant decrease in technical characteristics. Practical implications are as follows. Compliance with optimal FSWR proportions in composition of geopolymer and concrete mixtures makes it possible to reduce cost of raw materials; decrease FSWR amount; and support the closed economy principles in the construction industry.