GGGani G. Gilaev

Gani G. Gilaev

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Gani G. Gilaev has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Curing fluid for hydrocarbon-based cement slurries used in remedial cementing in oil and gas wells

    by M. S. Al-Edresi, G. G. Gilaev, S. V. Usov, М. С. Аль-Идриси, Г. Г. Гилаев, С. В. Усов

    Hydrocarbon-based cement slurries mixed with diesel fuel are used in remedial cementing in oil and gas wells, because they provide selective setting and are not prone to premature thickening. Their strength depends on how completely the hydrocarbon phase is replaced by the curing fluid. This article aims to determine the optimal composition and properties of the curing fluid during forced filtration through a hydrocarbon-based cement slurry to ensure maximum replacement of the hydrocarbon phase and high strength of the cement stone. The authors conducted 22 laboratory experiments using the setup for studying hydrocarbon cement slurries for two groups of formulations that differed in the hydrocarbon-to-cement ratio and the content of the nonionic surfactant Laureth-7. The study examined NaOH, Na₂CO₃, NaHCO₃, and Na₂SiO₃ and secondary nonionic surfactants in the aqueous phase of the curing fluid. The researchers identified that the strength of the cement stone is dependent on the concentration of the hydrophilizing agent. The highest strength was achieved by combining Laureth-7 in diesel fuel with NaOH in the curing fluid. The article ranked the hydrophilizing agents by effectiveness as follows: NaOH > Na₂CO₃ > NaHCO₃ > Na₂SiO₃. The optimal concentration ranges for effective removal of the hydrocarbon fraction from cement grain surfaces were also determined. The obtained dependencies can be used to develop procedures for restoring the integrity of the cement sheath in the annular space outside the casing.

  • The influence of the uneven distribution of deposits in the flow part of the centrifugal blower on the precession of its rotor

    by Mikhail S. Stepanov, Alexey V. Bunyakin, Gani G. Gilaev, Vladislav I. Dunaev

    This article considers a dynamic precession model of the shaft in a centrifugal supercharger of a gas pumping unit with two compression stages and sliding bearings. Precession is characterized by the trajectory of the shaft floating on one of the supporting bearing units or on two nodes synchronously. The authors have assessed the imbalance force resulting from uneven deposits at two compression stages (two impellers of natural gas supercharger). The calculated characteristics are compared with the measurement data on the gas pumping unit during its operation. This article provides analytical expressions for estimating the force causing the precession of the shaft and creating its imbalance. The results can be used to diagnose the presence of deposits on the impellers of the supercharger.

  • Method of selection and substantiation of the projected well optimal design based on geo-mechanical modeling

    by Samara Gtu, K.A. Shipovskiy, V.A. Kapitonov, M.E. Koval, G.G. Gilaev, Kub G T U

    В статье представлены основные методы определения градиентов горного (геостатического), порового (пластового) давления, гидроразрыва пласта, поглощения бурового раствора при вскрытии проницаемого пласта и после изоляционных работ. Установлено, что методика геомеханического моделирования горно-геологического разреза конкретного месторождения в сочетании с методом эмпирических коэффициентов эффективна для решения задачи выбора и обоснования оптимальной конструкции скважины. Предложена методика выбора и обоснования оптимальной конструкции проектируемой скважины на основе геомеханического моделирования с эмпирическими коэффициентами, учитывающими тектоническую...