Rui Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rui Zhao has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Xiaoshuai Wu
Hypersonic Technology Laboratory, College of Aerospace Science and Engineering, National University of Defense Technology 2 , Changsha 410073
2 shared publications - Yuxin Zhao
National University of Defense Technology
2 shared publications Xiaoshuai Wu
National University of Defense Technology
1 shared publicationYuxin Zhao
National University of Defense Technology
1 shared publication
Latest Publications
- 18 July 2026
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- p. 1-14
Direct Numerical Simulation of Supersonic Film Cooling Enhanced by a Backward-Facing Step
Supersonic film cooling is an effective strategy for thermal protection of hypersonic vehicles. The present study proposes a modified supersonic film-cooling configuration by introducing a backward-facing step beneath the film slot. Direct numerical simulations are conducted to investigate the flow characteristics and cooling performance across different step heights. The results show that the introduction of the step enhances film-cooling performance, and this effect becomes more pronounced as the step height increases. Within the investigated range, a maximum improvement of 45% is achieved as compared with the baseline case without a step. The step delays the mixing between the film and the mainstream, thereby extending the film coverage length. Further analysis of wall heat flux decomposition reveals that the extension of the effective cooling length is primarily caused by a reduction in the contribution from viscous dissipation. This reduction results from both the decreased shear stress beneath the film caused by the recirculation region and the suppression of turbulence development. Although the step enhances film-cooling performance, it also induces an aerodynamic penalty due to increased pressure drag. The optimal tradeoff between cooling enhancement and aerodynamic loss is achieved when the step height is equal to the film slot height.
- 18 July 2026
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- p. 1-14
Direct Numerical Simulation of Supersonic Film Cooling Enhanced by a Backward-Facing Step
Supersonic film cooling is an effective strategy for thermal protection of hypersonic vehicles. The present study proposes a modified supersonic film-cooling configuration by introducing a backward-facing step beneath the film slot. Direct numerical simulations are conducted to investigate the flow characteristics and cooling performance across different step heights. The results show that the introduction of the step enhances film-cooling performance, and this effect becomes more pronounced as the step height increases. Within the investigated range, a maximum improvement of 45% is achieved as compared with the baseline case without a step. The step delays the mixing between the film and the mainstream, thereby extending the film coverage length. Further analysis of wall heat flux decomposition reveals that the extension of the effective cooling length is primarily caused by a reduction in the contribution from viscous dissipation. This reduction results from both the decreased shear stress beneath the film caused by the recirculation region and the suppression of turbulence development. Although the step enhances film-cooling performance, it also induces an aerodynamic penalty due to increased pressure drag. The optimal tradeoff between cooling enhancement and aerodynamic loss is achieved when the step height is equal to the film slot height.
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Effect of film Mach number on supersonic film cooling using direct numerical simulation
Supersonic film cooling serves as an effective thermal protection method for hypersonic vehicles. This study performs direct numerical simulations of supersonic film injection into a hypersonic turbulent boundary layer (Mach 6), investigating the influence of film Mach number Mac on cooling performance and flow characteristics. Mean flow field data reveal that increasing Mac extends absolute effective cooling length, but is less cost-effective in terms of effective cooling length per unit film mass flow rate. Further analysis reveals that the diminished cost-effectiveness results from earlier boundary layer transition relative to the effective cooling length, which enhances turbulent mixing in the effective cooling region. Turbulent kinetic energy (TKE) evolution demonstrates that in the wall-jet region, the turbulent intensity at the lowest Mac (Mac=2) displays a one-peak pattern that differs significantly from the two-peak distributions under higher Mac conditions, which stems from the lowest film mass flow rate that causes rapid complete mixing. Bypass transition occurs in the boundary layer beneath the film. Although the absolute location of the transition onset is insensitive to Mac, the downstream turbulence development shows altered characteristics with increasing Mac, as evidenced by the peak TKE levels and spanwise length scales of turbulent structures. Interestingly, greater scale disparity between the turbulent structures near the wall and in the mixing layer is observed as Mac increases, which is attributed to the reduced spanwise scales of near-wall streaks. The increase in Mac results in decelerated turbulence development, extending the absolute streamwise distance required for the film to be completely dissipated.
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Effect of film Mach number on supersonic film cooling using direct numerical simulation
Supersonic film cooling serves as an effective thermal protection method for hypersonic vehicles. This study performs direct numerical simulations of supersonic film injection into a hypersonic turbulent boundary layer (Mach 6), investigating the influence of film Mach number Mac on cooling performance and flow characteristics. Mean flow field data reveal that increasing Mac extends absolute effective cooling length, but is less cost-effective in terms of effective cooling length per unit film mass flow rate. Further analysis reveals that the diminished cost-effectiveness results from earlier boundary layer transition relative to the effective cooling length, which enhances turbulent mixing in the effective cooling region. Turbulent kinetic energy (TKE) evolution demonstrates that in the wall-jet region, the turbulent intensity at the lowest Mac (Mac=2) displays a one-peak pattern that differs significantly from the two-peak distributions under higher Mac conditions, which stems from the lowest film mass flow rate that causes rapid complete mixing. Bypass transition occurs in the boundary layer beneath the film. Although the absolute location of the transition onset is insensitive to Mac, the downstream turbulence development shows altered characteristics with increasing Mac, as evidenced by the peak TKE levels and spanwise length scales of turbulent structures. Interestingly, greater scale disparity between the turbulent structures near the wall and in the mixing layer is observed as Mac increases, which is attributed to the reduced spanwise scales of near-wall streaks. The increase in Mac results in decelerated turbulence development, extending the absolute streamwise distance required for the film to be completely dissipated.
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
The turbulence evolution of tangential supersonic cooling film using direct numerical simulation
Supersonic film cooling is a potential approach to thermally protecting hypersonic aircraft. To unveil the turbulence evolution and inherent energy transport, a direct numerical simulation (DNS) of supersonic film cooling is performed, wherein the cooling gas with a Mach number of 2.0 is tangentially injected into a turbulent boundary layer with a Mach number of 3.0. Particular attention is paid to the evolution of turbulent structures reflected by energy spectra. The overall flow response can be described as the decay of upstream wall turbulence and the re-establishment of the downstream wall shear layer. Visualizations of vortex identification clearly show that well-shaped hairpin vortices oriented to the laminar cooling film are formed in the mixing layer. The decompositions of wall skin friction reveal that the tangential film causes considerable drag reduction downstream, and this is the joint benefit of the thickening of the wall shear layer and the decaying of upstream turbulence. The turbulent statistics reveal the coexistence of two energy peaks in the flow field. One in the mixing layer is the remnant of upstream turbulence and gradually decays, while the other near the wall is newly generated and keeps growing. The conclusion is further confirmed by energy spectra, which also show that streaky structures scaling differently from those in a turbulent boundary layer are formed near the wall. It is interesting to find that the two energy sites directly exchange turbulent kinetic energy through mean convection, and they redistribute energy toward the bracketing region through turbulent transport.
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
The turbulence evolution of tangential supersonic cooling film using direct numerical simulation
Supersonic film cooling is a potential approach to thermally protecting hypersonic aircraft. To unveil the turbulence evolution and inherent energy transport, a direct numerical simulation (DNS) of supersonic film cooling is performed, wherein the cooling gas with a Mach number of 2.0 is tangentially injected into a turbulent boundary layer with a Mach number of 3.0. Particular attention is paid to the evolution of turbulent structures reflected by energy spectra. The overall flow response can be described as the decay of upstream wall turbulence and the re-establishment of the downstream wall shear layer. Visualizations of vortex identification clearly show that well-shaped hairpin vortices oriented to the laminar cooling film are formed in the mixing layer. The decompositions of wall skin friction reveal that the tangential film causes considerable drag reduction downstream, and this is the joint benefit of the thickening of the wall shear layer and the decaying of upstream turbulence. The turbulent statistics reveal the coexistence of two energy peaks in the flow field. One in the mixing layer is the remnant of upstream turbulence and gradually decays, while the other near the wall is newly generated and keeps growing. The conclusion is further confirmed by energy spectra, which also show that streaky structures scaling differently from those in a turbulent boundary layer are formed near the wall. It is interesting to find that the two energy sites directly exchange turbulent kinetic energy through mean convection, and they redistribute energy toward the bracketing region through turbulent transport.