Yang Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yang Han has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Bingren Wang
College of Mechanical Engineering, Xi’an University of Science and Technology, Xi’an, China
1 shared publication- Bingren Wang
College of Mechanical Engineering, Xi’an University of Science and Technology 1 , Xi’an 710054
1 shared publication - Chenxin Han
College of Mechanical Engineering, Xi’an University of Science and Technology 1 , Xi’an 710054
1 shared publication Lei Wang
College of Mechanical Engineering, Xi’an Jiaotong University, Xi’an, China
1 shared publication- Lei Wang
National Additive Manufacturing Research Institute 2 , Xi’an 710075
1 shared publication Xiangtong Yan
College of Mechanical Engineering, Xi’an University of Science and Technology, Xi’an, China
1 shared publication
Latest Publications
- Open Access
- 1 March 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (3)
Jet electrolytic plasma polishing process for high temperature alloy additive manufacturing of large size surfaces
Aiming at the problem of surface finishing of large-size additively manufactured high-temperature alloy parts, a jet electrolytic plasma polishing process for the surface treatment of specific large-size high-temperature alloy samples has been developed. Taking the typical high-temperature alloy curved workpiece as the research object, through the orthogonal test research results, this research has studied the influence law of different process parameters on the surface roughness of the alloy and realized the verification of the process effect of the surface roughness of the high-temperature alloy surface polished by jet electrolytic plasma polishing. It was found that the degree of influence of the four process parameters on the surface roughness was in the following order: flow rate > cathode and anode spacing ≈ voltage > temperature. The process conditions adapted to the surface polishing of high-temperature alloys are as follows: a cathode and anode spacing of 25 mm, a voltage of 340 V, an electrolyte temperature of 70 °C, and an electrolyte flow rate of 1.2 l/h. The surface roughness of the workpiece obtained after polishing under these process conditions is the lowest, and the surface roughness (Ra) of high-temperature alloys decreases from 13.251 to 0.853 μm, with a decrease rate of 93.56%. The experimental results show that the impurity elements on the surface of the high-temperature alloy have been removed by electrolytic plasma polishing, the residue of electrolyte component elements is not detected, and the specimens treated by electrolyte plasma polishing present a better corrosion resistance.
- 1 March 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (3)
Open AccessJet electrolytic plasma polishing process for high temperature alloy additive manufacturing of large size surfaces
Aiming at the problem of surface finishing of large-size additively manufactured high-temperature alloy parts, a jet electrolytic plasma polishing process for the surface treatment of specific large-size high-temperature alloy samples has been developed. Taking the typical high-temperature alloy curved workpiece as the research object, through the orthogonal test research results, this research has studied the influence law of different process parameters on the surface roughness of the alloy and realized the verification of the process effect of the surface roughness of the high-temperature alloy surface polished by jet electrolytic plasma polishing. It was found that the degree of influence of the four process parameters on the surface roughness was in the following order: flow rate > cathode and anode spacing ≈ voltage > temperature. The process conditions adapted to the surface polishing of high-temperature alloys are as follows: a cathode and anode spacing of 25 mm, a voltage of 340 V, an electrolyte temperature of 70 °C, and an electrolyte flow rate of 1.2 l/h. The surface roughness of the workpiece obtained after polishing under these process conditions is the lowest, and the surface roughness (Ra) of high-temperature alloys decreases from 13.251 to 0.853 μm, with a decrease rate of 93.56%. The experimental results show that the impurity elements on the surface of the high-temperature alloy have been removed by electrolytic plasma polishing, the residue of electrolyte component elements is not detected, and the specimens treated by electrolyte plasma polishing present a better corrosion resistance.
- 4 January 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 239 (9) , 3287-3297
Research on electrolytic plasma polishing process for internal flow channel of superalloys alloy additive manufacturing parts
To solve the problem of poor surface quality of internal channel parts in additive manufacturing, the internal electrode electrolyte plasma polishing technology was used to improve the surface quality of the workpiece. The influence of different process parameters on the surface roughness of the internal channel was studied by orthogonal test. The experimental results show that for small caliber channels, polishing is more suitable for low voltage conditions. Under the conditions of polishing voltage 40 V, electrolyte temperature 80°C, moving speed of cathode wire 3 mm/min, and peristaltic pump speed 100 rpm, the roughness of the GH3536 inner channel sample is reduced from 15.1 to 2.793 μm. The order of influence of each factor is as follows: firstly voltage, secondly electrolyte temperature, then cathode wire traveling speed, and finally peristaltic pump speed. The roughness of GH4169 was reduced from 6.724 to 0.47 μm by polishing experiment. The results of the internal surface performance test show that the spherical powder on the surface of the workpiece disappears after polishing through the internal flow channel, the electrolyte component residue is not detected on the surface of the internal flow channel, and the corrosion resistance is significantly improved.
- 4 January 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 239 (9) , 3287-3297
Research on electrolytic plasma polishing process for internal flow channel of superalloys alloy additive manufacturing parts
To solve the problem of poor surface quality of internal channel parts in additive manufacturing, the internal electrode electrolyte plasma polishing technology was used to improve the surface quality of the workpiece. The influence of different process parameters on the surface roughness of the internal channel was studied by orthogonal test. The experimental results show that for small caliber channels, polishing is more suitable for low voltage conditions. Under the conditions of polishing voltage 40 V, electrolyte temperature 80°C, moving speed of cathode wire 3 mm/min, and peristaltic pump speed 100 rpm, the roughness of the GH3536 inner channel sample is reduced from 15.1 to 2.793 μm. The order of influence of each factor is as follows: firstly voltage, secondly electrolyte temperature, then cathode wire traveling speed, and finally peristaltic pump speed. The roughness of GH4169 was reduced from 6.724 to 0.47 μm by polishing experiment. The results of the internal surface performance test show that the spherical powder on the surface of the workpiece disappears after polishing through the internal flow channel, the electrolyte component residue is not detected on the surface of the internal flow channel, and the corrosion resistance is significantly improved.