Kyo-Moon Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kyo-Moon Lee has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Do-Hoon Shin
Aero-structure Development Engineering, Korean Air Aero-Space Division, Busan 46712, Republic of Korea
3 shared publicationsYun-Hae Kim
3 shared publications- Yun-Hae Kim
Korea Maritime and Ocean University
3 shared publications - Amutheesan Manikkavel
National Korea Maritime and Ocean University, Department of Advanced Materials Convergence Engineering, 727 Taejong-ro, Yeongdo-gu, Busan 49112, Republic of Korea
2 shared publications Sanjay Kumar
2 shared publications- Sanjay Kumar
Department of Ocean Advanced Materials Convergence Engineering, Korea Maritime and Ocean University, 727 Taejong-ro, Yeongdo-Gu, Busan 49112, Republic of Korea
2 shared publications
Latest Publications
- 5 March 2026
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics B
- Vol. 40 (09n10)
Fracture toughness and crack propagation analysis in CF/PEKK composites with hole defect: A comparative study of MBT and CBBM methods
This study experimentally investigated the effect of an open-hole (OH, W/[ ]) configuration on the Mode I fracture behavior of CF/PEKK thermoplastic composites. Double cantilever beam (DCB) tests were performed to analyze the influence of hole-induced discontinuities on crack initiation and propagation. The load–displacement responses were evaluated using the modified beam theory (MBT) and the compliance-based beam method (CBBM) to assess their applicability to defect-containing geometries. The Mode I fracture toughness values obtained from both methods exhibited good consistency within a [ ]% deviation, confirming the reliability of the data-based evaluation. The introduction of the hole decreased the critical fracture toughness at crack initiation by 16.6% (MBT) and 14% (CBBM), primarily due to stress concentration and local deformation irregularities near the defect. However, the reduction during crack propagation was much smaller — only 6.5% (MBT) and 3.7% (CBBM) — as the crack front became realigned and stabilized after passing through the hole. Microscopic observations revealed that fiber bridging governed the fracture resistance in both configurations. Even under defect conditions, no fiber breakage occurred; instead, interfacial debonding and matrix drawing were observed, maintaining the bridging effect throughout propagation. These results demonstrate that CBBM-based evaluation can effectively characterize Mode I fracture behavior in thermoplastic composites containing geometric discontinuities and provide a foundation for the defect-tolerant structural design of CF/PEKK composite components. This study particularly emphasizes that understanding the rapid initiation and propagation of cracks induced by geometric discontinuities is crucial for the effective design and application of CF/PEKK composites in structural components with holes or other local defects.
- 5 March 2026
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics B
- Vol. 40 (09n10)
Fracture toughness and crack propagation analysis in CF/PEKK composites with hole defect: A comparative study of MBT and CBBM methods
This study experimentally investigated the effect of an open-hole (OH, W/[ ]) configuration on the Mode I fracture behavior of CF/PEKK thermoplastic composites. Double cantilever beam (DCB) tests were performed to analyze the influence of hole-induced discontinuities on crack initiation and propagation. The load–displacement responses were evaluated using the modified beam theory (MBT) and the compliance-based beam method (CBBM) to assess their applicability to defect-containing geometries. The Mode I fracture toughness values obtained from both methods exhibited good consistency within a [ ]% deviation, confirming the reliability of the data-based evaluation. The introduction of the hole decreased the critical fracture toughness at crack initiation by 16.6% (MBT) and 14% (CBBM), primarily due to stress concentration and local deformation irregularities near the defect. However, the reduction during crack propagation was much smaller — only 6.5% (MBT) and 3.7% (CBBM) — as the crack front became realigned and stabilized after passing through the hole. Microscopic observations revealed that fiber bridging governed the fracture resistance in both configurations. Even under defect conditions, no fiber breakage occurred; instead, interfacial debonding and matrix drawing were observed, maintaining the bridging effect throughout propagation. These results demonstrate that CBBM-based evaluation can effectively characterize Mode I fracture behavior in thermoplastic composites containing geometric discontinuities and provide a foundation for the defect-tolerant structural design of CF/PEKK composite components. This study particularly emphasizes that understanding the rapid initiation and propagation of cracks induced by geometric discontinuities is crucial for the effective design and application of CF/PEKK composites in structural components with holes or other local defects.
- 23 November 2025
- Published by Elsevier in Composites Communications
- Vol. 60
Mode II fracture behavior of CF/PEKK composites with open-hole and bolted joint geometries at high-temperatures
- 23 November 2025
- Published by Elsevier in Composites Communications
- Vol. 60
Mode II fracture behavior of CF/PEKK composites with open-hole and bolted joint geometries at high-temperatures
- 12 April 2025
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 32 (07)
ENHANCING SURFACE ENERGY AND ADSORPTION CAPACITY ON CF/PEKK BONDING PERFORMANCE WITH HNT-MODIFIED PEI FILMS
Research has been conducted on joining Carbon fiber/Poly Ether Ketone Ketone (CF/PEKK) laminates. In terms of chemical bonding strength, adsorption capacity, closely linked to surface energy, plays a crucial role in enhancing chemical bonding. Laminates and adhesives should possess similar surface characteristics to improve adsorption capacity. Additionally, the polarity of the adhesive significantly enhances its adsorption capacity. Halloysite Nanotubes (HNTs), a type of nanoparticle, have garnered attention for their ability to improve the interfacial bonding strength of composites. With hydrogen bonding groups in their molecular structure, HNTs can increase the polarity of the polyetherimide (PEI) adhesive when incorporated, thereby enhancing its bonding performance. Thus, this study aimed to enhance the bonding performance of CF/PEKK laminates using a PEI adhesive. The laminate surface was treated with mechanical abrasion (MA) to improve the bonding strength, and the PEI adhesive film was modified by adding HNT. The wettability of the material was estimated using a contact angle test, which measures the wettability and surface energy of the material by analyzing the angle formed between a liquid droplet and the solid surface. The bonding strength was evaluated by measuring the lap shear strength.
- 12 April 2025
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 32 (07)
ENHANCING SURFACE ENERGY AND ADSORPTION CAPACITY ON CF/PEKK BONDING PERFORMANCE WITH HNT-MODIFIED PEI FILMS
Research has been conducted on joining Carbon fiber/Poly Ether Ketone Ketone (CF/PEKK) laminates. In terms of chemical bonding strength, adsorption capacity, closely linked to surface energy, plays a crucial role in enhancing chemical bonding. Laminates and adhesives should possess similar surface characteristics to improve adsorption capacity. Additionally, the polarity of the adhesive significantly enhances its adsorption capacity. Halloysite Nanotubes (HNTs), a type of nanoparticle, have garnered attention for their ability to improve the interfacial bonding strength of composites. With hydrogen bonding groups in their molecular structure, HNTs can increase the polarity of the polyetherimide (PEI) adhesive when incorporated, thereby enhancing its bonding performance. Thus, this study aimed to enhance the bonding performance of CF/PEKK laminates using a PEI adhesive. The laminate surface was treated with mechanical abrasion (MA) to improve the bonding strength, and the PEI adhesive film was modified by adding HNT. The wettability of the material was estimated using a contact angle test, which measures the wettability and surface energy of the material by analyzing the angle formed between a liquid droplet and the solid surface. The bonding strength was evaluated by measuring the lap shear strength.
- 5 April 2025
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 32 (07)
EFFECT OF FILM THICKNESS AND INFUSION PRESSURE ON INTERLAMINAR TOUGHENING OF CFRP LAMINATES TOUGHENED WITH MELT-INFUSED PA-6 FILM INTERLEAVES
Carbon fiber reinforced polymers (CFRPs) are extensively employed in high-performance applications because of their exceptional strength-to-weight ratio. However, their maximum potential is restricted by their susceptibility to delamination, a critical issue. This study examines the efficacy of melt-infused Polyamide-6 (PA-6) film interleaves in improving the interlaminar fracture toughness of CFRPs. This study observed substantial enhancements in the durability of both Modes I and II fractures by methodically adjusting the infusion pressure and film thickness. For the S_1_60 configuration, [ ] increased by 568%, reaching 2573.2[ ]J/m2, while [ ] improved by 596%. For the S_1_60 configuration, [ ] increased by 352% to 1278.1[ ]J/m2, while [ ] improved by 363%. Detailed fractographic studies were conducted to analyze the underlying mechanisms, which include plastic deformation, fiber bridging, and fiber pull-out. These results offer valuable insights into the optimization of melt-infusion interleaving to customize the mechanical performance of CFRPs. By controlling the infusion pressure and film thickness, it is possible to develop composite materials that are more resistant to damage and more durable, thereby broadening their potential for use in critical engineering applications in aeronautical, automotive and marine engineering.
- 5 April 2025
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 32 (07)
EFFECT OF FILM THICKNESS AND INFUSION PRESSURE ON INTERLAMINAR TOUGHENING OF CFRP LAMINATES TOUGHENED WITH MELT-INFUSED PA-6 FILM INTERLEAVES
Carbon fiber reinforced polymers (CFRPs) are extensively employed in high-performance applications because of their exceptional strength-to-weight ratio. However, their maximum potential is restricted by their susceptibility to delamination, a critical issue. This study examines the efficacy of melt-infused Polyamide-6 (PA-6) film interleaves in improving the interlaminar fracture toughness of CFRPs. This study observed substantial enhancements in the durability of both Modes I and II fractures by methodically adjusting the infusion pressure and film thickness. For the S_1_60 configuration, [ ] increased by 568%, reaching 2573.2[ ]J/m2, while [ ] improved by 596%. For the S_1_60 configuration, [ ] increased by 352% to 1278.1[ ]J/m2, while [ ] improved by 363%. Detailed fractographic studies were conducted to analyze the underlying mechanisms, which include plastic deformation, fiber bridging, and fiber pull-out. These results offer valuable insights into the optimization of melt-infusion interleaving to customize the mechanical performance of CFRPs. By controlling the infusion pressure and film thickness, it is possible to develop composite materials that are more resistant to damage and more durable, thereby broadening their potential for use in critical engineering applications in aeronautical, automotive and marine engineering.
- 11 February 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 296
Advancing carbon fiber and its composites technology: Korea's strategic growth and innovation
- 11 February 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 296
Advancing carbon fiber and its composites technology: Korea's strategic growth and innovation