Amutheesan Manikkavel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Amutheesan Manikkavel has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Vineet Kumar
School of Mechanical Engineering, Yeungnam University, 280 Daehak-Ro, Gyeongsan 38541, Gyeongbuk, Republic of Korea
5 shared publications - Sang-Shin Park
School of Mechanical Engineering, Yeungnam University, Gyeongsan 38541, Republic of Korea
4 shared publications - Yun-Hae Kim
Korea Maritime and Ocean University
3 shared publications - Kyo-Moon Lee
Department of Advanced Materials Convergence Engineering, National Korea Maritime and Ocean University, 727 Taejong-ro, Yeongdo-gu, Busan 49112, Republic of Korea
2 shared publications Najib Alam
2 shared publications- Anam Naz
Department of Ocean Advanced Materials Convergence Engineering, Korea Maritime and Ocean University, 727 Taejong-Ro, Yeongdo-Gu, Busan 49112, Korea
1 shared publication
Latest Publications
- 23 May 2025
- Published by IOP Publishing in Functional Composites and Structures
- Vol. 7 (2) , 025003
Flexural behavior of epoxy resin-based carbon fiber/halloysite nanotube hybrid reinforced composites under pre-bending load and hygroscopic conditions
Carbon fiber reinforced epoxy (CF/EP) composites are widely used in marine environments, facing challenges from water exposure and pre-bending (PB) during construction and service. While many studies have focused on the residual impact strength after pre-compression loading and the residual flexural strength of thermoplastic composites under various temperature conditions, nevertheless, analysis of the residual flexural behavior after PB in situations such as water absorption environments with thermosetting composites remains limited. In this study, residual flexural behavior under water absorption conditions was analyzed to evaluate the influence of PB and water absorption in residual flexural strength with CF/EP. In particular, the research examines CF/EP composites reinforced with halloysite nanotubes (HNTs), evaluating their residual flexural strength after PB under various conditions: room temperature, water immersion, and post-immersion. Results show that HNTs enhance flexural strength and modulus by improving fiber–matrix interfacial bonding and reducing water absorption due to their non-polar surface. Under 80% PB, HNT-reinforced composites exhibited significantly lower reductions in flexural strength (5%) and modulus (14%) compared to unreinforced CF/EP (15% and 24%, respectively). These reductions are attributed to fiber kinking and misalignment induced by compressive loads. Water absorption further deteriorates flexural properties, leading to non-linear stress–strain behavior. Specimens pre-bent after water immersion showed more pronounced property degradation compared to those pre-bent before immersion. This combined effect arises from weakened interfacial bonding due to water ingress and the formation of kink bands under compressive loads. This study emphasizes the critical importance of considering both water absorption and PB during the design and application of CF/EP composites in marine environments. The incorporation of HNTs offers a promising approach to enhance the durability and performance of these composites in such challenging conditions.
- 23 May 2025
- Published by IOP Publishing in Functional Composites and Structures
- Vol. 7 (2) , 025003
Flexural behavior of epoxy resin-based carbon fiber/halloysite nanotube hybrid reinforced composites under pre-bending load and hygroscopic conditions
Carbon fiber reinforced epoxy (CF/EP) composites are widely used in marine environments, facing challenges from water exposure and pre-bending (PB) during construction and service. While many studies have focused on the residual impact strength after pre-compression loading and the residual flexural strength of thermoplastic composites under various temperature conditions, nevertheless, analysis of the residual flexural behavior after PB in situations such as water absorption environments with thermosetting composites remains limited. In this study, residual flexural behavior under water absorption conditions was analyzed to evaluate the influence of PB and water absorption in residual flexural strength with CF/EP. In particular, the research examines CF/EP composites reinforced with halloysite nanotubes (HNTs), evaluating their residual flexural strength after PB under various conditions: room temperature, water immersion, and post-immersion. Results show that HNTs enhance flexural strength and modulus by improving fiber–matrix interfacial bonding and reducing water absorption due to their non-polar surface. Under 80% PB, HNT-reinforced composites exhibited significantly lower reductions in flexural strength (5%) and modulus (14%) compared to unreinforced CF/EP (15% and 24%, respectively). These reductions are attributed to fiber kinking and misalignment induced by compressive loads. Water absorption further deteriorates flexural properties, leading to non-linear stress–strain behavior. Specimens pre-bent after water immersion showed more pronounced property degradation compared to those pre-bent before immersion. This combined effect arises from weakened interfacial bonding due to water ingress and the formation of kink bands under compressive loads. This study emphasizes the critical importance of considering both water absorption and PB during the design and application of CF/EP composites in marine environments. The incorporation of HNTs offers a promising approach to enhance the durability and performance of these composites in such challenging conditions.
- 12 April 2025
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 32 (07)
ENHANCING SURFACE ENERGY AND ADSORPTION CAPACITY ON CF/PEKK BONDING PERFORMANCE WITH HNT-MODIFIED PEI FILMS
Research has been conducted on joining Carbon fiber/Poly Ether Ketone Ketone (CF/PEKK) laminates. In terms of chemical bonding strength, adsorption capacity, closely linked to surface energy, plays a crucial role in enhancing chemical bonding. Laminates and adhesives should possess similar surface characteristics to improve adsorption capacity. Additionally, the polarity of the adhesive significantly enhances its adsorption capacity. Halloysite Nanotubes (HNTs), a type of nanoparticle, have garnered attention for their ability to improve the interfacial bonding strength of composites. With hydrogen bonding groups in their molecular structure, HNTs can increase the polarity of the polyetherimide (PEI) adhesive when incorporated, thereby enhancing its bonding performance. Thus, this study aimed to enhance the bonding performance of CF/PEKK laminates using a PEI adhesive. The laminate surface was treated with mechanical abrasion (MA) to improve the bonding strength, and the PEI adhesive film was modified by adding HNT. The wettability of the material was estimated using a contact angle test, which measures the wettability and surface energy of the material by analyzing the angle formed between a liquid droplet and the solid surface. The bonding strength was evaluated by measuring the lap shear strength.
- 12 April 2025
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 32 (07)
ENHANCING SURFACE ENERGY AND ADSORPTION CAPACITY ON CF/PEKK BONDING PERFORMANCE WITH HNT-MODIFIED PEI FILMS
Research has been conducted on joining Carbon fiber/Poly Ether Ketone Ketone (CF/PEKK) laminates. In terms of chemical bonding strength, adsorption capacity, closely linked to surface energy, plays a crucial role in enhancing chemical bonding. Laminates and adhesives should possess similar surface characteristics to improve adsorption capacity. Additionally, the polarity of the adhesive significantly enhances its adsorption capacity. Halloysite Nanotubes (HNTs), a type of nanoparticle, have garnered attention for their ability to improve the interfacial bonding strength of composites. With hydrogen bonding groups in their molecular structure, HNTs can increase the polarity of the polyetherimide (PEI) adhesive when incorporated, thereby enhancing its bonding performance. Thus, this study aimed to enhance the bonding performance of CF/PEKK laminates using a PEI adhesive. The laminate surface was treated with mechanical abrasion (MA) to improve the bonding strength, and the PEI adhesive film was modified by adding HNT. The wettability of the material was estimated using a contact angle test, which measures the wettability and surface energy of the material by analyzing the angle formed between a liquid droplet and the solid surface. The bonding strength was evaluated by measuring the lap shear strength.
- 5 April 2025
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 32 (07)
EFFECT OF FILM THICKNESS AND INFUSION PRESSURE ON INTERLAMINAR TOUGHENING OF CFRP LAMINATES TOUGHENED WITH MELT-INFUSED PA-6 FILM INTERLEAVES
Carbon fiber reinforced polymers (CFRPs) are extensively employed in high-performance applications because of their exceptional strength-to-weight ratio. However, their maximum potential is restricted by their susceptibility to delamination, a critical issue. This study examines the efficacy of melt-infused Polyamide-6 (PA-6) film interleaves in improving the interlaminar fracture toughness of CFRPs. This study observed substantial enhancements in the durability of both Modes I and II fractures by methodically adjusting the infusion pressure and film thickness. For the S_1_60 configuration, [ ] increased by 568%, reaching 2573.2[ ]J/m2, while [ ] improved by 596%. For the S_1_60 configuration, [ ] increased by 352% to 1278.1[ ]J/m2, while [ ] improved by 363%. Detailed fractographic studies were conducted to analyze the underlying mechanisms, which include plastic deformation, fiber bridging, and fiber pull-out. These results offer valuable insights into the optimization of melt-infusion interleaving to customize the mechanical performance of CFRPs. By controlling the infusion pressure and film thickness, it is possible to develop composite materials that are more resistant to damage and more durable, thereby broadening their potential for use in critical engineering applications in aeronautical, automotive and marine engineering.
- 5 April 2025
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 32 (07)
EFFECT OF FILM THICKNESS AND INFUSION PRESSURE ON INTERLAMINAR TOUGHENING OF CFRP LAMINATES TOUGHENED WITH MELT-INFUSED PA-6 FILM INTERLEAVES
Carbon fiber reinforced polymers (CFRPs) are extensively employed in high-performance applications because of their exceptional strength-to-weight ratio. However, their maximum potential is restricted by their susceptibility to delamination, a critical issue. This study examines the efficacy of melt-infused Polyamide-6 (PA-6) film interleaves in improving the interlaminar fracture toughness of CFRPs. This study observed substantial enhancements in the durability of both Modes I and II fractures by methodically adjusting the infusion pressure and film thickness. For the S_1_60 configuration, [ ] increased by 568%, reaching 2573.2[ ]J/m2, while [ ] improved by 596%. For the S_1_60 configuration, [ ] increased by 352% to 1278.1[ ]J/m2, while [ ] improved by 363%. Detailed fractographic studies were conducted to analyze the underlying mechanisms, which include plastic deformation, fiber bridging, and fiber pull-out. These results offer valuable insights into the optimization of melt-infusion interleaving to customize the mechanical performance of CFRPs. By controlling the infusion pressure and film thickness, it is possible to develop composite materials that are more resistant to damage and more durable, thereby broadening their potential for use in critical engineering applications in aeronautical, automotive and marine engineering.
- 23 February 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (7) , 6629-6643
Multifunctionality of MWCNT and TiC hybrid filler silicone composite for energy harvesting and strain sensing
The flexible silicone elastomer‐conductive composite was developed with enhanced energy harvesting and strain sensing. A hybrid nanofiller system with multi‐walled carbon nanotubes (MWCNTs) and titanium (IV) carbide (TiC) was used as reinforcing agents for the elastomer. The 4 MWCNT +5 TiC composite has 1.34 MPa tensile strength, 136.85% higher than unfilled silicone rubber (SR) matrix. The unfilled sample has a 1.558 MPa compressive modulus, while 4 MWCNT +5 TiC has 3.87 MPa. The machine and finger presses were utilized to test the energy harvesting of the composite. With greater cyclic stability, the 4 MWCNT +5 TiC sample performed exceptionally well in the machine press in the output voltage range of around 120 mV. Among the thumb presses, 2 MWCNT +5 TiC yielded the best results, with a voltage of about 100 mV. The 3 MWCNT +5 TiC sample produced 9044% more energy than the single filler 3 phr MWCNT sample from our previous work. Higher MWCNT content enhanced composite stiffness, making finger pressing harder and decreasing energy output. The strain sensing test on the 4 MWCNT +5 TiC composite showed high gauge factors (GF = 7.532 and 23.944) and good linearity (R2 = 0.909 and 0.939) over a strain range of Δε = 0%–14% and 14%–22%. Silicone composites' mechanical, energy harvesting, and strain sensing performance improved greatly with the MWCNT and TiC hybrid fillers. These composites could be used in self‐powered wearable electronics, machine or structural deformation monitoring, and human motion sensing.Highlights: A stretchable device was developed with improved energy harvesting and strain sensing. Rubber composites were fabricated from MWCNTs, TiC hybrid fillers, and SR matrix. The energy harvesting was 9044% higher for hybrid filler compared to MWCNT as the only filler. Robust strain sensing properties with a gauge factor of 23.9, linearity of 0.91, and relaxation time of 0.1 s. The final composites are useful for self‐powered wearable electronics, health monitoring, and human motion sensing.
- 23 February 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (7) , 6629-6643
Multifunctionality of MWCNT and TiC hybrid filler silicone composite for energy harvesting and strain sensing
The flexible silicone elastomer‐conductive composite was developed with enhanced energy harvesting and strain sensing. A hybrid nanofiller system with multi‐walled carbon nanotubes (MWCNTs) and titanium (IV) carbide (TiC) was used as reinforcing agents for the elastomer. The 4 MWCNT +5 TiC composite has 1.34 MPa tensile strength, 136.85% higher than unfilled silicone rubber (SR) matrix. The unfilled sample has a 1.558 MPa compressive modulus, while 4 MWCNT +5 TiC has 3.87 MPa. The machine and finger presses were utilized to test the energy harvesting of the composite. With greater cyclic stability, the 4 MWCNT +5 TiC sample performed exceptionally well in the machine press in the output voltage range of around 120 mV. Among the thumb presses, 2 MWCNT +5 TiC yielded the best results, with a voltage of about 100 mV. The 3 MWCNT +5 TiC sample produced 9044% more energy than the single filler 3 phr MWCNT sample from our previous work. Higher MWCNT content enhanced composite stiffness, making finger pressing harder and decreasing energy output. The strain sensing test on the 4 MWCNT +5 TiC composite showed high gauge factors (GF = 7.532 and 23.944) and good linearity (R2 = 0.909 and 0.939) over a strain range of Δε = 0%–14% and 14%–22%. Silicone composites' mechanical, energy harvesting, and strain sensing performance improved greatly with the MWCNT and TiC hybrid fillers. These composites could be used in self‐powered wearable electronics, machine or structural deformation monitoring, and human motion sensing.Highlights: A stretchable device was developed with improved energy harvesting and strain sensing. Rubber composites were fabricated from MWCNTs, TiC hybrid fillers, and SR matrix. The energy harvesting was 9044% higher for hybrid filler compared to MWCNT as the only filler. Robust strain sensing properties with a gauge factor of 23.9, linearity of 0.91, and relaxation time of 0.1 s. The final composites are useful for self‐powered wearable electronics, health monitoring, and human motion sensing.
- 6 June 2022
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 28 (4) , 813-827
Stretchable piezo‐electric energy harvesting device with high durability using carbon nanomaterials with different structure and their synergism with molybdenum disulfide
Recently, polymer composite based stretchable piezo‐electric energy harvesting device have attracted a great attention in composite industry. At laboratory scale, these piezo‐electric devices have ability to generate impressive voltage (~8 V) with high durability (>0.5 million cycles) depending upon nature of the material used in electrode and substrate. In this work, composites were prepared by mixing room temperature vulcanized silicone rubber (RTV‐SR) and nanofillers such as multi‐wall carbon nanotube (MWCNT), nano‐carbon black (nano‐CB), graphite nanoplatelets (GNP), in single or hybrid with molybdenum disulfide (MoS 2 ). These fillers differentiate on basis of their structure ranging from 0‐dimensional (0‐D) to 3‐D. The effects of these structures on mechanical properties are demonstrated. Among them, MWCNT with 1‐D, tube shape morphology, high aspect ratio of 65 shows dominating mechanical properties even at 2 per hundred parts of rubber (phr) loading followed by nano‐CB, GNP at 8 phr and MoS 2 at 2 phr. A synergistic effect in mechanical properties between hybrid fillers such as tensile strength and fracture strain was demonstrated. In the end, the composites were tested for piezo‐electric energy generation and durability cycles for the best candidate such as MWCNT was tested for up to 0.5 million cycles was demonstrated.
- 6 June 2022
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 28 (4) , 813-827
Stretchable piezo‐electric energy harvesting device with high durability using carbon nanomaterials with different structure and their synergism with molybdenum disulfide
Recently, polymer composite based stretchable piezo‐electric energy harvesting device have attracted a great attention in composite industry. At laboratory scale, these piezo‐electric devices have ability to generate impressive voltage (~8 V) with high durability (>0.5 million cycles) depending upon nature of the material used in electrode and substrate. In this work, composites were prepared by mixing room temperature vulcanized silicone rubber (RTV‐SR) and nanofillers such as multi‐wall carbon nanotube (MWCNT), nano‐carbon black (nano‐CB), graphite nanoplatelets (GNP), in single or hybrid with molybdenum disulfide (MoS 2 ). These fillers differentiate on basis of their structure ranging from 0‐dimensional (0‐D) to 3‐D. The effects of these structures on mechanical properties are demonstrated. Among them, MWCNT with 1‐D, tube shape morphology, high aspect ratio of 65 shows dominating mechanical properties even at 2 per hundred parts of rubber (phr) loading followed by nano‐CB, GNP at 8 phr and MoS 2 at 2 phr. A synergistic effect in mechanical properties between hybrid fillers such as tensile strength and fracture strain was demonstrated. In the end, the composites were tested for piezo‐electric energy generation and durability cycles for the best candidate such as MWCNT was tested for up to 0.5 million cycles was demonstrated.
- 15 December 2021
- Published by Wiley in Polymer Composites
- Vol. 43 (3) , 1305-1318
Investigation of high temperature vulcanized and room temperature vulcanized silicone rubber based on flexible piezo‐electric energy harvesting applications with multi‐walled carbon nanotube reinforced composites
Flexible energy harvester can be able to produce continuous voltage output under the mechanical deformations. High temperature vulcanized (HTV) and room temperature vulcanized (RTV) silicone rubbers are used for making the flexible piezo‐electric energy harvester. A total of 1 and 2 phr of multi‐walled carbon nanotube (MWCNT) are used as the electrode material mixed with the rubber solution for the preparation of flexible electrode. Cyclic loading machine is used for the application of 2 Hz of bi‐axial load and uniaxial compression load in the specimen. One centimeter depth of displacement is applied during the bi‐axial cyclic loading and 4 mm amplitude of displacement is applied during the compression loading. Tensile and compression tests are performed to determine the engineering properties of the material. Tensile load withstanding value of the silicone rubber is increasing as increasing the MWCNT filler in the rubber. Tensile value of the pure HTV silicone rubber is 10.020 N and for 2 phr MWCNT reinforced rubber is 22.106 N. Compressive withstanding load of pure HTV rubber is 189.565 N and for 2 phr MWCNT reinforced rubber is 287.066 N. HTV silicone rubber is the highly stiffness material on compares with RTV rubber based on the tensile and the compressive value. Transmission electron microscopy, optical micrographs, and scanning electron microscope show the morphology of MWCNT and surface image of specimen. A total of 2 mm substrate based 2 phr MWCNT reinforced HTV flexible energy harvester undergo decrease in voltage during the cyclic loading due to breakage of electrode. A total of 2 phr MWCNT electrode‐based sample can be able to produce more output voltage than 1 phr MWCNT electrode‐based sample during bi‐axial and compression loading. More voltage is produced in the compression specimen than bi‐axial one.
- 15 December 2021
- Published by Wiley in Polymer Composites
- Vol. 43 (3) , 1305-1318
Investigation of high temperature vulcanized and room temperature vulcanized silicone rubber based on flexible piezo‐electric energy harvesting applications with multi‐walled carbon nanotube reinforced composites
Flexible energy harvester can be able to produce continuous voltage output under the mechanical deformations. High temperature vulcanized (HTV) and room temperature vulcanized (RTV) silicone rubbers are used for making the flexible piezo‐electric energy harvester. A total of 1 and 2 phr of multi‐walled carbon nanotube (MWCNT) are used as the electrode material mixed with the rubber solution for the preparation of flexible electrode. Cyclic loading machine is used for the application of 2 Hz of bi‐axial load and uniaxial compression load in the specimen. One centimeter depth of displacement is applied during the bi‐axial cyclic loading and 4 mm amplitude of displacement is applied during the compression loading. Tensile and compression tests are performed to determine the engineering properties of the material. Tensile load withstanding value of the silicone rubber is increasing as increasing the MWCNT filler in the rubber. Tensile value of the pure HTV silicone rubber is 10.020 N and for 2 phr MWCNT reinforced rubber is 22.106 N. Compressive withstanding load of pure HTV rubber is 189.565 N and for 2 phr MWCNT reinforced rubber is 287.066 N. HTV silicone rubber is the highly stiffness material on compares with RTV rubber based on the tensile and the compressive value. Transmission electron microscopy, optical micrographs, and scanning electron microscope show the morphology of MWCNT and surface image of specimen. A total of 2 mm substrate based 2 phr MWCNT reinforced HTV flexible energy harvester undergo decrease in voltage during the cyclic loading due to breakage of electrode. A total of 2 phr MWCNT electrode‐based sample can be able to produce more output voltage than 1 phr MWCNT electrode‐based sample during bi‐axial and compression loading. More voltage is produced in the compression specimen than bi‐axial one.