Takaaki Tanno
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Takaaki Tanno has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Ryosuke Adachi
Faculty of Science and Engineering, Chuo University Faculty of Science and Engineering Graduate School of Science and Engineering, 1-13-27 Kasuga, Bunkyo, Tokyo, 112-8551, JAPAN
3 shared publications- Taro Nakamura
Chuo University
3 shared publications Koya Tsurumi
Faculty of Science and Engineering, Chuo University Faculty of Science and Engineering Graduate School of Science and Engineering, 1-13-27 Kasuga, Bunkyo, Tokyo, 112-8551, JAPAN
2 shared publications- Takuya Umedachi
Graduate School of Science and Technology, Shinshu University, 3-15-1 Tokida, Ueda, Ngano, 386-8567, JAPAN
2 shared publications - Akihiro Ohnishi
Department of Fermentation Science, Faculty of Applied Bio-science, Tokyo University of Agriculture, Tokyo, Japan
1 shared publication Editorial Office
1 shared publication
Latest Publications
- 23 February 2026
- Published by IOP Publishing in Bioinspiration & Biomimetics
- Vol. 21 (2) , 026003
Content-state-driven motility switching in an intestine-inspired soft-bodied robot via decentralised oscillator networks
Adaptive handling of thick or composition-changing fluids is difficult for conventional pumps. In animals, the intestine addresses this challenge by switching between segmental mixing and peristaltic transport according to the physical state of the contents. We translate this principle into a silicone soft pump composed of four pneumatic chambers, each driven by its own phase oscillator. Two tunable factors govern the collective behaviour: (i) the coupling strength, which attempts to maintain neighbouring oscillators in a travelling-wave relationship, and (ii) the local sensor feedback, which forces each oscillator to correct the deformation error of its own chamber. Numerical bifurcation analysis and time-domain simulations show that when the two strengths are balanced within an intermediate range, the controller first generates an antiphase pattern that homogenises a viscous mixture, and then spontaneously shifts to a quarter-cycle travelling wave that drives the now-fluid contents downstream. We built a physical prototype and experimentally confirmed autonomous mode switching between two glycerol-based fluids of contrasting viscosity. These results demonstrate that a minimal, bioinspired, distributed controller can endow soft devices with adaptive, multifunctional pumping capability, thereby opening new routes to food-processing, biomedical, and chemical-handling systems that operate under uncertain conditions.
- 23 February 2026
- Published by IOP Publishing in Bioinspiration & Biomimetics
- Vol. 21 (2) , 026003
Content-state-driven motility switching in an intestine-inspired soft-bodied robot via decentralised oscillator networks
Adaptive handling of thick or composition-changing fluids is difficult for conventional pumps. In animals, the intestine addresses this challenge by switching between segmental mixing and peristaltic transport according to the physical state of the contents. We translate this principle into a silicone soft pump composed of four pneumatic chambers, each driven by its own phase oscillator. Two tunable factors govern the collective behaviour: (i) the coupling strength, which attempts to maintain neighbouring oscillators in a travelling-wave relationship, and (ii) the local sensor feedback, which forces each oscillator to correct the deformation error of its own chamber. Numerical bifurcation analysis and time-domain simulations show that when the two strengths are balanced within an intermediate range, the controller first generates an antiphase pattern that homogenises a viscous mixture, and then spontaneously shifts to a quarter-cycle travelling wave that drives the now-fluid contents downstream. We built a physical prototype and experimentally confirmed autonomous mode switching between two glycerol-based fluids of contrasting viscosity. These results demonstrate that a minimal, bioinspired, distributed controller can endow soft devices with adaptive, multifunctional pumping capability, thereby opening new routes to food-processing, biomedical, and chemical-handling systems that operate under uncertain conditions.
- 15 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 10 (11) , 11498-11505
Autonomous Decentralized Control for Motion Switching in an Intestine-Inspired Peristaltic Mixing Pump Adaptive to Physical Phase Transitions of Mixed Materials
In this paper, we developed an autonomous decentralized control method that incorporates phase-difference adjustment based on a sigmoid function, enabling the design of both increases and decreases in discrepancy. The method was applied to a peristaltic mixing pump capable of mixing and transporting solid–liquid multiphase fluids. This study aims to realize a soft robotics system that autonomously switches motion modes according to changes in the physical properties of the transported material, thereby integratively mimicking both the motility and motion-switching functions of the intestine. Conventional autonomous decentralized control methods have been applied to the locomotion of amoeba-type and snake-type robots. However, when such control laws are applied to pumps, it is difficult to achieve appropriate motion switching in environments where the contents harden due to mixing. In this paper, we employed a sigmoid function that allows bidirectional control of discrepancy and constructed a new control law based on target phase-difference adjustment without feedback. The control law was implemented in a four-unit pump, and we confirmed that the desired motion patterns could be reproduced according to the preset target phase differences. As a result, the phase differences between all units converged to the target values within approximately 10–30 s after actuation began, producing the intended motion patterns. Furthermore, polyvinyl alcohol solution and borax water were used as contents whose fluidity decreases during mixing. We verified that autonomous motion switching occurred as the discrepancy increased. The results showed that, in units containing hardened material, a conveying motion with a phase difference of π/3 was generated, whereas in units with residual unmixed material, a mixing motion with a phase difference of π was generated. These findings demonstrate that the proposed method enables motion control that adapts to changes in material properties.
- 15 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 10 (11) , 11498-11505
Autonomous Decentralized Control for Motion Switching in an Intestine-Inspired Peristaltic Mixing Pump Adaptive to Physical Phase Transitions of Mixed Materials
In this paper, we developed an autonomous decentralized control method that incorporates phase-difference adjustment based on a sigmoid function, enabling the design of both increases and decreases in discrepancy. The method was applied to a peristaltic mixing pump capable of mixing and transporting solid–liquid multiphase fluids. This study aims to realize a soft robotics system that autonomously switches motion modes according to changes in the physical properties of the transported material, thereby integratively mimicking both the motility and motion-switching functions of the intestine. Conventional autonomous decentralized control methods have been applied to the locomotion of amoeba-type and snake-type robots. However, when such control laws are applied to pumps, it is difficult to achieve appropriate motion switching in environments where the contents harden due to mixing. In this paper, we employed a sigmoid function that allows bidirectional control of discrepancy and constructed a new control law based on target phase-difference adjustment without feedback. The control law was implemented in a four-unit pump, and we confirmed that the desired motion patterns could be reproduced according to the preset target phase differences. As a result, the phase differences between all units converged to the target values within approximately 10–30 s after actuation began, producing the intended motion patterns. Furthermore, polyvinyl alcohol solution and borax water were used as contents whose fluidity decreases during mixing. We verified that autonomous motion switching occurred as the discrepancy increased. The results showed that, in units containing hardened material, a conveying motion with a phase difference of π/3 was generated, whereas in units with residual unmixed material, a mixing motion with a phase difference of π was generated. These findings demonstrate that the proposed method enables motion control that adapts to changes in material properties.
- Open Access
- 20 February 2025
- Published by Fuji Technology Press Ltd. in Journal of Robotics and Mechatronics
- Vol. 37 (1) , 172-184
Construction of a Mixing State Estimation System in a Peristaltic Mixing Conveyor that Imitates Intestine —Proposal of an Estimation Method to Improve Generalizability for Mixture’s Input Conditions—
A peristaltic mixing and conveyor that imitates the intestines of living organisms is used to mix powders and highly viscous fluids at low shear force in the manufacturing processes of foods, pharmaceuticals, paints, cosmetics, and other products. Although the device uses sequence control to mix and convey the contents, the actual intestine controls its motion autonomously according to the state of the contents. This research aims to establish an autonomous control method that can change between mixing and conveying according to the state of the mixture. In this paper, we propose a method to construct a learning model that is not affected by the content input conditions, in which samples with different total input amounts and mixing ratios are fed into the device, and sensor values acquired during the device operation are used as training data. The generalizability of the learning model was verified, and it was shown that mixing state estimation was possible up to 20 min from the start of mixing for mixtures with different input amounts and input order.
- 20 February 2025
- Published by Fuji Technology Press Ltd. in Journal of Robotics and Mechatronics
- Vol. 37 (1) , 172-184
Open AccessConstruction of a Mixing State Estimation System in a Peristaltic Mixing Conveyor that Imitates Intestine —Proposal of an Estimation Method to Improve Generalizability for Mixture’s Input Conditions—
A peristaltic mixing and conveyor that imitates the intestines of living organisms is used to mix powders and highly viscous fluids at low shear force in the manufacturing processes of foods, pharmaceuticals, paints, cosmetics, and other products. Although the device uses sequence control to mix and convey the contents, the actual intestine controls its motion autonomously according to the state of the contents. This research aims to establish an autonomous control method that can change between mixing and conveying according to the state of the mixture. In this paper, we propose a method to construct a learning model that is not affected by the content input conditions, in which samples with different total input amounts and mixing ratios are fed into the device, and sensor values acquired during the device operation are used as training data. The generalizability of the learning model was verified, and it was shown that mixing state estimation was possible up to 20 min from the start of mixing for mixtures with different input amounts and input order.