Yuji Iwami
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Yuji Iwami has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Kenya Horita
Ironmaking Research Department, Steel Research Laboratory, JFE Steel Corporation
3 shared publications Kunihiko Nakashima
Department of Materials, Graduate School of Engineering, Kyushu University
3 shared publicationsTetsuya Yamamoto
Ironmaking Research Department, Steel Research Laboratory, JFE Steel Corporation
3 shared publications- Hideya Nakamura
Department of Chemical Engineering, Osaka Metropolitan University
2 shared publications Kensuke Kumeda
Department of Chemical Engineering, Osaka Metropolitan University
2 shared publications- Noritaka Saito
Department of Materials, Graduate School of Engineering, Kyushu University
2 shared publications
Latest Publications
- Open Access
- 15 November 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (12) , 1483-1491
Effect of Quicklime Addition on the Strength of Green Pellets from Fine Ore Powders with Different Degrees of Reduction
In the iron-making process, wet granulation is a key process for utilizing dephosphorized fine ore powders as a raw material. However, dephosphorized ore powders with higher degree of reduction can result in a significant decrease in strength of the green pellets. Moreover, pellet-strength-enhancing effect by adding quicklime was less pronounced in reduced iron ore powder. Therefore, it is essential to investigate the underlying mechanisms that are responsible for the less binder efficiency of quicklime in reduced fine ore powders. To this end, this study investigated effect of quicklime addition on the compressive strength of green pellets prepared from magnetite and hematite. The results exhibited that the addition of quicklime to hematite can significantly enhance their green pellet strength, whereas the addition to magnetite resulted in no strength-enhancing effect on the pellet. The agitation torque of wet powder samples suggested that in the hematite the quicklime reacted well with added water, enhancing the plasticity of the wet powder. In contrast, in the magnetite the quicklime was unlikely to react with water, resulting in much less plasticity-enhancing effect. From several characterizations, wettability of the ore powder was considered to be a key property causing this contrasting response. A mechanistic scenario arising from hydration reaction of quicklime and subsequent formation of fine particles was proposed as a cause of the contrasting response. Finally, it was demonstrated that the green pellet strength can be significantly increased by using ground quicklime.
- 15 November 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (12) , 1483-1491
Open AccessEffect of Quicklime Addition on the Strength of Green Pellets from Fine Ore Powders with Different Degrees of Reduction
In the iron-making process, wet granulation is a key process for utilizing dephosphorized fine ore powders as a raw material. However, dephosphorized ore powders with higher degree of reduction can result in a significant decrease in strength of the green pellets. Moreover, pellet-strength-enhancing effect by adding quicklime was less pronounced in reduced iron ore powder. Therefore, it is essential to investigate the underlying mechanisms that are responsible for the less binder efficiency of quicklime in reduced fine ore powders. To this end, this study investigated effect of quicklime addition on the compressive strength of green pellets prepared from magnetite and hematite. The results exhibited that the addition of quicklime to hematite can significantly enhance their green pellet strength, whereas the addition to magnetite resulted in no strength-enhancing effect on the pellet. The agitation torque of wet powder samples suggested that in the hematite the quicklime reacted well with added water, enhancing the plasticity of the wet powder. In contrast, in the magnetite the quicklime was unlikely to react with water, resulting in much less plasticity-enhancing effect. From several characterizations, wettability of the ore powder was considered to be a key property causing this contrasting response. A mechanistic scenario arising from hydration reaction of quicklime and subsequent formation of fine particles was proposed as a cause of the contrasting response. Finally, it was demonstrated that the green pellet strength can be significantly increased by using ground quicklime.
- Open Access
- 15 October 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (11) , 1300-1311
Yield Prediction Based on Bed Temperature and Component in Sintering Process
The yield in the iron ore sintering process is managed in daily operations as an important indicator of manufacturing costs and CO2 emissions. Currently, general yield operation actions are "feedback" based on yield results, and do not prevent yield loss. In order to prevent yield decline by "feed-forward" type action targeting yield changes, yield prediction based on operating conditions is essential. In this study, we assumed that yield is synonymous with the strength of the discharged sintered cake, and attempted to apply the porous material strength estimation formula to the sintered cake. The sintered cake was divided into a cake pore part lost by crushing and a sintered ore part as a matrix portion containing pores that remain after crushing, and the formulation of cake porosity and sintered ore strength was studied. Using the amount of melt (melting ratio) generated in liquid-phase sintering and its penetration length into the ore as key factors, the estimation formulas for cake porosity and sintered ore strength were built. In addition, experiments using diffusion pairs were carried out to verify the hypothesis regarding the penetration distance. A pot test were carried out to verify the constructed model , and confirmed a good correlation between the calculated yield by bed temperature measured and the blending components, and the actual measured yield.
- 15 October 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (11) , 1300-1311
Open AccessYield Prediction Based on Bed Temperature and Component in Sintering Process
The yield in the iron ore sintering process is managed in daily operations as an important indicator of manufacturing costs and CO2 emissions. Currently, general yield operation actions are "feedback" based on yield results, and do not prevent yield loss. In order to prevent yield decline by "feed-forward" type action targeting yield changes, yield prediction based on operating conditions is essential. In this study, we assumed that yield is synonymous with the strength of the discharged sintered cake, and attempted to apply the porous material strength estimation formula to the sintered cake. The sintered cake was divided into a cake pore part lost by crushing and a sintered ore part as a matrix portion containing pores that remain after crushing, and the formulation of cake porosity and sintered ore strength was studied. Using the amount of melt (melting ratio) generated in liquid-phase sintering and its penetration length into the ore as key factors, the estimation formulas for cake porosity and sintered ore strength were built. In addition, experiments using diffusion pairs were carried out to verify the hypothesis regarding the penetration distance. A pot test were carried out to verify the constructed model , and confirmed a good correlation between the calculated yield by bed temperature measured and the blending components, and the actual measured yield.
- Open Access
- 15 January 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (1) , 56-65
Microstructures and Reduction Properties of High CaO Concentration Sintered Ore
The reduction disintegration index (RDI) of sintered ore, which is the main raw material of blast furnaces, greatly affects blast furnace operation. In order to improve RDI without deteriorating the reducibility index (RI), sintered ore having a CaO concentration of 20 mass%, which is higher than the conventional 10 mass% when using porous Australian iron ore, was produced, and its effects on the mineral structure, porosity, RI and RDI were evaluated.In the sintered ore having a CaO concentration of 20 mass%, hematite decreased and calcium-ferrite (sum of other component system calcium-ferrite and binary calcium-ferrite), the SFCA-I/SFCA ratio and porosity increased in comparison with that having a CaO concentration of 10 mass%.When Australian iron ore was used as a raw material for sintered ore, RI increased in sintered ore having a CaO concentration of 20 mass% compared with the one having a CaO concentration of 10 mass%. In addition, RDI was improved in the sintered ore having a CaO concentration of 20 mass% compared with the that having a CaO concentration of 10 mass%. This is due to the formation of binary calcium-ferrite instead of secondary hematite, which deteriorates RDI.
- 15 January 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (1) , 56-65
Open AccessMicrostructures and Reduction Properties of High CaO Concentration Sintered Ore
The reduction disintegration index (RDI) of sintered ore, which is the main raw material of blast furnaces, greatly affects blast furnace operation. In order to improve RDI without deteriorating the reducibility index (RI), sintered ore having a CaO concentration of 20 mass%, which is higher than the conventional 10 mass% when using porous Australian iron ore, was produced, and its effects on the mineral structure, porosity, RI and RDI were evaluated.In the sintered ore having a CaO concentration of 20 mass%, hematite decreased and calcium-ferrite (sum of other component system calcium-ferrite and binary calcium-ferrite), the SFCA-I/SFCA ratio and porosity increased in comparison with that having a CaO concentration of 10 mass%.When Australian iron ore was used as a raw material for sintered ore, RI increased in sintered ore having a CaO concentration of 20 mass% compared with the one having a CaO concentration of 10 mass%. In addition, RDI was improved in the sintered ore having a CaO concentration of 20 mass% compared with the that having a CaO concentration of 10 mass%. This is due to the formation of binary calcium-ferrite instead of secondary hematite, which deteriorates RDI.
- 1 January 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (9) , 992-1000
Reduction and Melting Behaviors of Deposited Carbon-Iron Oxide Composite in Hydrogen Atmosphere
- 1 January 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (9) , 992-1000
Reduction and Melting Behaviors of Deposited Carbon-Iron Oxide Composite in Hydrogen Atmosphere
- Open Access
- 1 May 2025
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 111 (7) , 355-367
Yield Prediction Based on Bed Temperature and Component in Sintering Process
The yield in the iron ore sintering process is managed in daily operations as an important indicator of manufacturing costs and CO2 emissions. Currently, general yield operation actions are "feedback" based on yield results, and do not prevent yield loss. In order to prevent yield decline by "feed-forward" type action targeting yield changes, yield prediction based on operating conditions is essential. In this study, we assumed that yield is synonymous with the strength of the discharged sintered cake, and attempted to apply the porous material strength estimation formula to the sintered cake. The sintered cake was divided into a cake pore part lost by crushing and a sintered ore part as a matrix portion containing pores that remain after crushing, and the formulation of cake porosity and sintered ore strength was studied. Using the amount of melt (melting ratio) generated in liquid-phase sintering and its penetration length into the ore as key factors, the estimation formulas for cake porosity and sintered ore strength were built. In addition, experiments using diffusion pairs were carried out to verify the hypothesis regarding the penetration distance. A pot test were carried out to verify the constructed model , and confirmed a good correlation between the calculated yield by bed temperature measured and the blending components, and the actual measured yield.
- 1 May 2025
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 111 (7) , 355-367
Open AccessYield Prediction Based on Bed Temperature and Component in Sintering Process
The yield in the iron ore sintering process is managed in daily operations as an important indicator of manufacturing costs and CO2 emissions. Currently, general yield operation actions are "feedback" based on yield results, and do not prevent yield loss. In order to prevent yield decline by "feed-forward" type action targeting yield changes, yield prediction based on operating conditions is essential. In this study, we assumed that yield is synonymous with the strength of the discharged sintered cake, and attempted to apply the porous material strength estimation formula to the sintered cake. The sintered cake was divided into a cake pore part lost by crushing and a sintered ore part as a matrix portion containing pores that remain after crushing, and the formulation of cake porosity and sintered ore strength was studied. Using the amount of melt (melting ratio) generated in liquid-phase sintering and its penetration length into the ore as key factors, the estimation formulas for cake porosity and sintered ore strength were built. In addition, experiments using diffusion pairs were carried out to verify the hypothesis regarding the penetration distance. A pot test were carried out to verify the constructed model , and confirmed a good correlation between the calculated yield by bed temperature measured and the blending components, and the actual measured yield.
- Open Access
- 15 January 2025
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 65 (1) , 62-69
Relationship between the Agitation Torque of the Wet Iron Ore Powder and Pellet Properties
Handling dephosphorized iron-ore powders with varying sizes and degrees of reduction is a pivotal issue in the iron-making process. A wet granulation process is employed for using dephosphorised fine ore powders as raw materials; however, it is difficult to determine the optimum water content to produce green pellets with the required physical properties because of the significant variation in the physicochemical properties of the dephosphorized ore powders. Thus, developing a method to determine the optimum water content for producing green pellets from fine ore powders with various degrees of reduction is necessary. In this study, we propose a method to estimate the optimum water content using agitation torque, which is a rheological property of wet ore powders. To this end, we investigated the effects of the hematite/magnetite fraction in the raw ore powder mixture on the agitation torque and green pellet properties. The characteristics of the agitation torque profile and green pellet properties (density and compressive strength) changed significantly depending on the hematite/magnetite fraction. Subsequently, we investigated the relationship between the agitation torque and green pellet properties, which revealed that the density and compressive strength of the green pellets correlated well when the product of the agitation torque and tumbling time was employed as the explanatory variable, regardless of the hematite/magnetite fraction. Thus, the properties of green pellets produced from fine ore powders with various degrees of reduction can be estimated based on the rheological properties measured by the agitation torque.
- 15 January 2025
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 65 (1) , 62-69
Open AccessRelationship between the Agitation Torque of the Wet Iron Ore Powder and Pellet Properties
Handling dephosphorized iron-ore powders with varying sizes and degrees of reduction is a pivotal issue in the iron-making process. A wet granulation process is employed for using dephosphorised fine ore powders as raw materials; however, it is difficult to determine the optimum water content to produce green pellets with the required physical properties because of the significant variation in the physicochemical properties of the dephosphorized ore powders. Thus, developing a method to determine the optimum water content for producing green pellets from fine ore powders with various degrees of reduction is necessary. In this study, we propose a method to estimate the optimum water content using agitation torque, which is a rheological property of wet ore powders. To this end, we investigated the effects of the hematite/magnetite fraction in the raw ore powder mixture on the agitation torque and green pellet properties. The characteristics of the agitation torque profile and green pellet properties (density and compressive strength) changed significantly depending on the hematite/magnetite fraction. Subsequently, we investigated the relationship between the agitation torque and green pellet properties, which revealed that the density and compressive strength of the green pellets correlated well when the product of the agitation torque and tumbling time was employed as the explanatory variable, regardless of the hematite/magnetite fraction. Thus, the properties of green pellets produced from fine ore powders with various degrees of reduction can be estimated based on the rheological properties measured by the agitation torque.
- 15 December 2018
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 58 (12) , 2200-2209
Improvement of Sinter Productivity by Control of Magnetite Ore Segregation in Sintering Bed
- 15 December 2018
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 58 (12) , 2200-2209
Improvement of Sinter Productivity by Control of Magnetite Ore Segregation in Sintering Bed