Kenya Horita
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Kenya Horita has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Tetsuya Yamamoto
Ironmaking Research Department, Steel Research Laboratory, JFE Steel Corporation
3 shared publications- Yuji Iwami
Steel Research Laboratory, JFE Steel Corporation
3 shared publications - Kenta Takehara
Steel Research Laboratory, JFE Steel Corporation
2 shared publications Kunihiko Nakashima
Department of Materials, Graduate School of Engineering, Kyushu University
2 shared publications- Noritaka Saito
Department of Materials, Graduate School of Engineering, Kyushu University
2 shared publications - Takahide Higuchi
Steel Research Laboratory, JFE Steel Corporation
2 shared publications
Latest Publications
- Open Access
- 15 October 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (11) , 1300-1311
Yield Prediction Based on Bed Temperature and Component in Sintering Process
The yield in the iron ore sintering process is managed in daily operations as an important indicator of manufacturing costs and CO2 emissions. Currently, general yield operation actions are "feedback" based on yield results, and do not prevent yield loss. In order to prevent yield decline by "feed-forward" type action targeting yield changes, yield prediction based on operating conditions is essential. In this study, we assumed that yield is synonymous with the strength of the discharged sintered cake, and attempted to apply the porous material strength estimation formula to the sintered cake. The sintered cake was divided into a cake pore part lost by crushing and a sintered ore part as a matrix portion containing pores that remain after crushing, and the formulation of cake porosity and sintered ore strength was studied. Using the amount of melt (melting ratio) generated in liquid-phase sintering and its penetration length into the ore as key factors, the estimation formulas for cake porosity and sintered ore strength were built. In addition, experiments using diffusion pairs were carried out to verify the hypothesis regarding the penetration distance. A pot test were carried out to verify the constructed model , and confirmed a good correlation between the calculated yield by bed temperature measured and the blending components, and the actual measured yield.
- 15 October 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (11) , 1300-1311
Open AccessYield Prediction Based on Bed Temperature and Component in Sintering Process
The yield in the iron ore sintering process is managed in daily operations as an important indicator of manufacturing costs and CO2 emissions. Currently, general yield operation actions are "feedback" based on yield results, and do not prevent yield loss. In order to prevent yield decline by "feed-forward" type action targeting yield changes, yield prediction based on operating conditions is essential. In this study, we assumed that yield is synonymous with the strength of the discharged sintered cake, and attempted to apply the porous material strength estimation formula to the sintered cake. The sintered cake was divided into a cake pore part lost by crushing and a sintered ore part as a matrix portion containing pores that remain after crushing, and the formulation of cake porosity and sintered ore strength was studied. Using the amount of melt (melting ratio) generated in liquid-phase sintering and its penetration length into the ore as key factors, the estimation formulas for cake porosity and sintered ore strength were built. In addition, experiments using diffusion pairs were carried out to verify the hypothesis regarding the penetration distance. A pot test were carried out to verify the constructed model , and confirmed a good correlation between the calculated yield by bed temperature measured and the blending components, and the actual measured yield.
- Open Access
Quantitative Evaluation of Sinter Reducibility Under Simulated Blast Furnace Conditions Using Microstructure Estimated by Hyperspectral Imaging
Precise control of sinter reducibility is essential for stable blast furnace operation. Each mineral phase present in sinter, such as hematite, magnetite and calcium ferrite exhibits different reducibility. In XRD analysis, the requirement for sample pulverization leads to the loss of mineralogical texture information. This makes it difficult to quantitatively correlate the complex mineral phases present in the sinter with reducibility. This study introduces a novel quantitative approach using hyperspectral imaging to distinguish specific mineral morphologies. Reduction experiments simulating blast furnace thermal and gas conditions were conducted on several sinters. Multiple regression analysis was applied to correlate mineral fractions and macroporosity with reduction rates across three distinct reduction stages. In the low-temperature stage, hematite, macroporosity and acicular calcium ferrites were identified as the primary drivers of reduction. In the intermediate stage, acicular calcium ferrites continued to enhance reactivity, whereas coarse calcium ferrite showed a significant negative influence. In the high-temperature stage, macroporosity strongly promoted reduction, while coarse calcium ferrite and magnetite hindered it due to the formation of shell-like metallic iron structures which impede gas diffusion. These findings demonstrate that hyperspectral imaging combined with multi-stage regression analysis offers a useful tool for designing optimal sinter mineralogy for blast furnace performance.
Open AccessQuantitative Evaluation of Sinter Reducibility Under Simulated Blast Furnace Conditions Using Microstructure Estimated by Hyperspectral Imaging
Precise control of sinter reducibility is essential for stable blast furnace operation. Each mineral phase present in sinter, such as hematite, magnetite and calcium ferrite exhibits different reducibility. In XRD analysis, the requirement for sample pulverization leads to the loss of mineralogical texture information. This makes it difficult to quantitatively correlate the complex mineral phases present in the sinter with reducibility. This study introduces a novel quantitative approach using hyperspectral imaging to distinguish specific mineral morphologies. Reduction experiments simulating blast furnace thermal and gas conditions were conducted on several sinters. Multiple regression analysis was applied to correlate mineral fractions and macroporosity with reduction rates across three distinct reduction stages. In the low-temperature stage, hematite, macroporosity and acicular calcium ferrites were identified as the primary drivers of reduction. In the intermediate stage, acicular calcium ferrites continued to enhance reactivity, whereas coarse calcium ferrite showed a significant negative influence. In the high-temperature stage, macroporosity strongly promoted reduction, while coarse calcium ferrite and magnetite hindered it due to the formation of shell-like metallic iron structures which impede gas diffusion. These findings demonstrate that hyperspectral imaging combined with multi-stage regression analysis offers a useful tool for designing optimal sinter mineralogy for blast furnace performance.
- Open Access
- 15 January 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (1) , 56-65
Microstructures and Reduction Properties of High CaO Concentration Sintered Ore
The reduction disintegration index (RDI) of sintered ore, which is the main raw material of blast furnaces, greatly affects blast furnace operation. In order to improve RDI without deteriorating the reducibility index (RI), sintered ore having a CaO concentration of 20 mass%, which is higher than the conventional 10 mass% when using porous Australian iron ore, was produced, and its effects on the mineral structure, porosity, RI and RDI were evaluated.In the sintered ore having a CaO concentration of 20 mass%, hematite decreased and calcium-ferrite (sum of other component system calcium-ferrite and binary calcium-ferrite), the SFCA-I/SFCA ratio and porosity increased in comparison with that having a CaO concentration of 10 mass%.When Australian iron ore was used as a raw material for sintered ore, RI increased in sintered ore having a CaO concentration of 20 mass% compared with the one having a CaO concentration of 10 mass%. In addition, RDI was improved in the sintered ore having a CaO concentration of 20 mass% compared with the that having a CaO concentration of 10 mass%. This is due to the formation of binary calcium-ferrite instead of secondary hematite, which deteriorates RDI.
- 15 January 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (1) , 56-65
Open AccessMicrostructures and Reduction Properties of High CaO Concentration Sintered Ore
The reduction disintegration index (RDI) of sintered ore, which is the main raw material of blast furnaces, greatly affects blast furnace operation. In order to improve RDI without deteriorating the reducibility index (RI), sintered ore having a CaO concentration of 20 mass%, which is higher than the conventional 10 mass% when using porous Australian iron ore, was produced, and its effects on the mineral structure, porosity, RI and RDI were evaluated.In the sintered ore having a CaO concentration of 20 mass%, hematite decreased and calcium-ferrite (sum of other component system calcium-ferrite and binary calcium-ferrite), the SFCA-I/SFCA ratio and porosity increased in comparison with that having a CaO concentration of 10 mass%.When Australian iron ore was used as a raw material for sintered ore, RI increased in sintered ore having a CaO concentration of 20 mass% compared with the one having a CaO concentration of 10 mass%. In addition, RDI was improved in the sintered ore having a CaO concentration of 20 mass% compared with the that having a CaO concentration of 10 mass%. This is due to the formation of binary calcium-ferrite instead of secondary hematite, which deteriorates RDI.
- Open Access
- 15 August 2025
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 111 (12) , 760-770
Microstructures and Reduction Properties of High CaO Concentration Sintered Ore
The reduction disintegration index (RDI) of sintered ore, which is the main raw material of blast furnaces, greatly affects blast furnace operation. In order to improve RDI without deteriorating the reducibility index (RI), sintered ore having a CaO concentration of 20 mass%, which is higher than the conventional 10 mass% when using porous Australian iron ore, was produced, and its effects on the mineral structure, porosity, RI and RDI were evaluated. In the sintered ore having a CaO concentration of 20 mass%, hematite decreased and calcium-ferrite (sum of other component system calcium-ferrite and binary calcium-ferrite), the SFCA-I/SFCA ratio and porosity increased in comparison with that having a CaO concentration of 10 mass%. When Australian iron ore was used as a raw material for sintered ore, RI increased in sintered ore having a CaO concentration of 20 mass% compared with the one having a CaO concentration of 10 mass%. In addition, RDI was improved in the sintered ore having a CaO concentration of 20 mass% compared with the that having a CaO concentration of 10 mass%. This is due to the formation of binary calcium-ferrite instead of secondary hematite, which deteriorates RDI.
- 15 August 2025
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 111 (12) , 760-770
Open AccessMicrostructures and Reduction Properties of High CaO Concentration Sintered Ore
The reduction disintegration index (RDI) of sintered ore, which is the main raw material of blast furnaces, greatly affects blast furnace operation. In order to improve RDI without deteriorating the reducibility index (RI), sintered ore having a CaO concentration of 20 mass%, which is higher than the conventional 10 mass% when using porous Australian iron ore, was produced, and its effects on the mineral structure, porosity, RI and RDI were evaluated. In the sintered ore having a CaO concentration of 20 mass%, hematite decreased and calcium-ferrite (sum of other component system calcium-ferrite and binary calcium-ferrite), the SFCA-I/SFCA ratio and porosity increased in comparison with that having a CaO concentration of 10 mass%. When Australian iron ore was used as a raw material for sintered ore, RI increased in sintered ore having a CaO concentration of 20 mass% compared with the one having a CaO concentration of 10 mass%. In addition, RDI was improved in the sintered ore having a CaO concentration of 20 mass% compared with the that having a CaO concentration of 10 mass%. This is due to the formation of binary calcium-ferrite instead of secondary hematite, which deteriorates RDI.
- Open Access
- 1 May 2025
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 111 (7) , 355-367
Yield Prediction Based on Bed Temperature and Component in Sintering Process
The yield in the iron ore sintering process is managed in daily operations as an important indicator of manufacturing costs and CO2 emissions. Currently, general yield operation actions are "feedback" based on yield results, and do not prevent yield loss. In order to prevent yield decline by "feed-forward" type action targeting yield changes, yield prediction based on operating conditions is essential. In this study, we assumed that yield is synonymous with the strength of the discharged sintered cake, and attempted to apply the porous material strength estimation formula to the sintered cake. The sintered cake was divided into a cake pore part lost by crushing and a sintered ore part as a matrix portion containing pores that remain after crushing, and the formulation of cake porosity and sintered ore strength was studied. Using the amount of melt (melting ratio) generated in liquid-phase sintering and its penetration length into the ore as key factors, the estimation formulas for cake porosity and sintered ore strength were built. In addition, experiments using diffusion pairs were carried out to verify the hypothesis regarding the penetration distance. A pot test were carried out to verify the constructed model , and confirmed a good correlation between the calculated yield by bed temperature measured and the blending components, and the actual measured yield.
- 1 May 2025
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 111 (7) , 355-367
Open AccessYield Prediction Based on Bed Temperature and Component in Sintering Process
The yield in the iron ore sintering process is managed in daily operations as an important indicator of manufacturing costs and CO2 emissions. Currently, general yield operation actions are "feedback" based on yield results, and do not prevent yield loss. In order to prevent yield decline by "feed-forward" type action targeting yield changes, yield prediction based on operating conditions is essential. In this study, we assumed that yield is synonymous with the strength of the discharged sintered cake, and attempted to apply the porous material strength estimation formula to the sintered cake. The sintered cake was divided into a cake pore part lost by crushing and a sintered ore part as a matrix portion containing pores that remain after crushing, and the formulation of cake porosity and sintered ore strength was studied. Using the amount of melt (melting ratio) generated in liquid-phase sintering and its penetration length into the ore as key factors, the estimation formulas for cake porosity and sintered ore strength were built. In addition, experiments using diffusion pairs were carried out to verify the hypothesis regarding the penetration distance. A pot test were carried out to verify the constructed model , and confirmed a good correlation between the calculated yield by bed temperature measured and the blending components, and the actual measured yield.