Ayman A. Al-Dharrab
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ayman A. Al-Dharrab has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
Seham B. Tayel
Department of Oral and Maxillofacial Rehabilitation, Faculty of Dentistry, King Abdulaziz University, P.O. Box 80209, Jeddah 21589, Saudi Arabia
2 shared publicationsLana A. Shinawi
King Abdulaziz University, Prosthodontics department, Faculty of Dentistry. Jeddah, Saudi Arabia
1 shared publicationMona H. Abodaya
Faculty of Dentistry, Alexandria University, Alexandria 21534, Egypt
1 shared publication- Tamer M. Nassef
October University for Modern Sciences and Arts (MSA),Faculty of Computer Science,Giza,Egypt
1 shared publication
Latest Publications
- Open Access
- 28 March 2013
- Published by Wiley in ISRN Dentistry
- Vol. 2013, 1-9
The Effect of Different Storage Conditions on the Physical Properties of Pigmented Medical Grade I Silicone Maxillofacial Material
Objective. This study aimed to evaluate the effect of different storage solutions that simulate acidic, alkaline, and sebum conditiions on the physical properties of pigmented (colorant elastomer) cosmesil M511 maxillofacial prosthetic material. Materials and Methods. Sixty specimens were prepared according to the manufacturer's instructions and were tested before and after immersion of different storage conditions for six months at 37 °C. The following tests were performed: color changes (group I), solution absorption (group II), surface roughness (group III), and scanning electron microscopy (group IV). Results. There were no significant changes observed in the color and solution absorption tests while surface roughness revealed significant difference between control group and other testing storage medium groups, and this result was supported by SEM analysis that revealed limited surface changes. Conclusions. Cosmaseil material is an acceptable cross-linked formulation that withstands storage in different solutions with variable pH. The addition of pigment cannot vary the physical properties of these materials. Surface roughness test as well as SEM microscopic study showed moderate changes indicating a limited effect on the surface of the material.
- 28 March 2013
- Published by Wiley in ISRN Dentistry
- Vol. 2013, 1-9
Open AccessThe Effect of Different Storage Conditions on the Physical Properties of Pigmented Medical Grade I Silicone Maxillofacial Material
Objective. This study aimed to evaluate the effect of different storage solutions that simulate acidic, alkaline, and sebum conditiions on the physical properties of pigmented (colorant elastomer) cosmesil M511 maxillofacial prosthetic material. Materials and Methods. Sixty specimens were prepared according to the manufacturer's instructions and were tested before and after immersion of different storage conditions for six months at 37 °C. The following tests were performed: color changes (group I), solution absorption (group II), surface roughness (group III), and scanning electron microscopy (group IV). Results. There were no significant changes observed in the color and solution absorption tests while surface roughness revealed significant difference between control group and other testing storage medium groups, and this result was supported by SEM analysis that revealed limited surface changes. Conclusions. Cosmaseil material is an acceptable cross-linked formulation that withstands storage in different solutions with variable pH. The addition of pigment cannot vary the physical properties of these materials. Surface roughness test as well as SEM microscopic study showed moderate changes indicating a limited effect on the surface of the material.
- 1 January 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
A novel computational analysis of computer milled zirconium implant abutment head design under reinforced implant supported overdenture
During the past few decades, unalloyed titanium has been extensively used as a material of dental implant-supported restorations but it cause gingival discoloration and unnatural appearance of the surrounding soft tissue. Currently, yttrium oxide partially-stabilized zirconia (Y-TZP) is a ceramic of special interest because of its superior mechanical properties. This study was carried out with four one piece zirconium implants embedded on a standard acrylic resin mandibular edentulous model, the abutment of zirconium implant was classified into two designs and then laboratory test was applied with proposed biting force (sensor (BS) and a bidirectional transmit-receive module. Our study concluded that the use of one piece Zirconium implant with box or parallel shape abutment head in implant supported over-denture without a need of cement, screws or plastics or metal housing for attachment in other types of implant had a superior results and easier maintenance and repair of the prosthesis if any complications occur.
- 1 January 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
A novel computational analysis of computer milled zirconium implant abutment head design under reinforced implant supported overdenture
During the past few decades, unalloyed titanium has been extensively used as a material of dental implant-supported restorations but it cause gingival discoloration and unnatural appearance of the surrounding soft tissue. Currently, yttrium oxide partially-stabilized zirconia (Y-TZP) is a ceramic of special interest because of its superior mechanical properties. This study was carried out with four one piece zirconium implants embedded on a standard acrylic resin mandibular edentulous model, the abutment of zirconium implant was classified into two designs and then laboratory test was applied with proposed biting force (sensor (BS) and a bidirectional transmit-receive module. Our study concluded that the use of one piece Zirconium implant with box or parallel shape abutment head in implant supported over-denture without a need of cement, screws or plastics or metal housing for attachment in other types of implant had a superior results and easier maintenance and repair of the prosthesis if any complications occur.