Bowen Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bowen Yang has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Hongshuai Huang
College of Aviation Engineering, Civil Aviation Flight University of China, Guanghan 618307, China
2 shared publications - Shaolong Li
College of Aviation Engineering Civil Aviation Flight University of China Chengdu Sichuan China
2 shared publications - Wenfeng Yang
College of Aviation Engineering, Civil Aviation Flight University of China, Guanghan 618307, China
2 shared publications - Yu Cao
Intelligent Manufacturing Institute of Laser and Optoelectronic, Wenzhou University, Wenzhou 325035, China
2 shared publications - Junchao Li
College of Aviation Engineering, Civil Aviation Flight University of China, Guanghan 618307, China
1 shared publication - Ran Zhang
The Second Research Institute of Civil Aviation Administration of China, Chengdu 610041, China
1 shared publication
Latest Publications
- Open Access
Multiscale Characterization and Evaluation of Low-Energy Bird-Strike Damage in CFRP
Carbon fiber-reinforced polymer (CFRP) laminates are susceptible to barely visible impact damage (BVID) under low-energy bird-strike-like conditions. However, in previous studies, most damage evaluations for BVID were limited to a single scale. In this work, a multiscale characterization and evaluation method integrating the analytic hierarchy process (AHP) and the CRITIC weighting method was proposed to investigate the damage evolution of CFRP laminates under low-energy impacts (approximately 12–33 J). Delamination area (SDa), indentation depth (PD), surface crack aspect ratio (RA), energy dissipation, and compression-after-impact (CAI) strength were analyzed based on phased-array ultrasonic C-scanning, 3D optical profilometry, and scanning electron microscopy. The results showed that PD, SDa, and energy dissipation increased from 108.73 μm to 213.93 μm, from 228.6 mm2 to 695.8 mm2, and from 5.96 J to 21.40 J, respectively, with increasing impact energy. Meanwhile, CAI strength decreased from 202.2 MPa to 118.9 MPa, with a maximum degradation rate of 41.16%. A critical transition was observed in the medium-to-high energy range, where delamination growth gradually plateaued, while intralaminar cracking and fiber fracture became increasingly dominant. The proposed framework enables quantitative grading of BVID severity and provides a practical basis for assessing residual damage in impacted CFRP laminates.
Open AccessMultiscale Characterization and Evaluation of Low-Energy Bird-Strike Damage in CFRP
Carbon fiber-reinforced polymer (CFRP) laminates are susceptible to barely visible impact damage (BVID) under low-energy bird-strike-like conditions. However, in previous studies, most damage evaluations for BVID were limited to a single scale. In this work, a multiscale characterization and evaluation method integrating the analytic hierarchy process (AHP) and the CRITIC weighting method was proposed to investigate the damage evolution of CFRP laminates under low-energy impacts (approximately 12–33 J). Delamination area (SDa), indentation depth (PD), surface crack aspect ratio (RA), energy dissipation, and compression-after-impact (CAI) strength were analyzed based on phased-array ultrasonic C-scanning, 3D optical profilometry, and scanning electron microscopy. The results showed that PD, SDa, and energy dissipation increased from 108.73 μm to 213.93 μm, from 228.6 mm2 to 695.8 mm2, and from 5.96 J to 21.40 J, respectively, with increasing impact energy. Meanwhile, CAI strength decreased from 202.2 MPa to 118.9 MPa, with a maximum degradation rate of 41.16%. A critical transition was observed in the medium-to-high energy range, where delamination growth gradually plateaued, while intralaminar cracking and fiber fracture became increasingly dominant. The proposed framework enables quantitative grading of BVID severity and provides a practical basis for assessing residual damage in impacted CFRP laminates.
- Open Access
Design and Validation of a Dielectric Method-Based Composite Material Curing Monitoring Platform
Monitoring the curing process is crucial for guiding and optimizing the curing procedures of composite material repair patches. Traditional embedded online monitoring methods are limited in their ability to track the curing process of these patches. This paper presents a composite material curing monitoring platform designed using dielectric methods. It integrates temperature control, pressure control, dielectric signal acquisition, control and display modules, and is specifically tailored for bag molding curing of repair patches. The platform measures the ionic viscosity of T300 2019B composites, analyzes the curing index, and correlates it with DSC-cured degree tests. The results indicate that the multiple ionic viscosity curves obtained from monitoring exhibit consistent trends, with correlation coefficients between curves exceeding 0.96. The changes in curing index align with the changes in curing degree, demonstrating that the platform can reliably and accurately monitor the ionic viscosity of repair patches. This platform enables effective monitoring of the ionic viscosity during the curing process of composite material repair patches.
Open AccessDesign and Validation of a Dielectric Method-Based Composite Material Curing Monitoring Platform
Monitoring the curing process is crucial for guiding and optimizing the curing procedures of composite material repair patches. Traditional embedded online monitoring methods are limited in their ability to track the curing process of these patches. This paper presents a composite material curing monitoring platform designed using dielectric methods. It integrates temperature control, pressure control, dielectric signal acquisition, control and display modules, and is specifically tailored for bag molding curing of repair patches. The platform measures the ionic viscosity of T300 2019B composites, analyzes the curing index, and correlates it with DSC-cured degree tests. The results indicate that the multiple ionic viscosity curves obtained from monitoring exhibit consistent trends, with correlation coefficients between curves exceeding 0.96. The changes in curing index align with the changes in curing degree, demonstrating that the platform can reliably and accurately monitor the ionic viscosity of repair patches. This platform enables effective monitoring of the ionic viscosity during the curing process of composite material repair patches.