Martin Frommherz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Martin Frommherz has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Dmitry Naumenko
Institute of Energy and Climate Research (IEK-2) Forschungszentrum Juelich Wilhelm-Johnen-Straße Juelich 52428 Germany
2 shared publications - Elena Yazhenskikh
Forschungszentrum Jülich GmbH, IWV-2, D-52425 Jülich, Germany
2 shared publications - Michael Müller
Institute of Energy Materials and Devices, IMD‐1: Structure and Function of Materials Forschungszentrum Jülich GmbH 52425 Jülich Germany
2 shared publications - Rishi Pillai
Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, USA
2 shared publications - Yaping Wang
Institute of Energy and Climate Research (IEK-2) Forschungszentrum Juelich Wilhelm-Johnen-Straße Juelich 52428 Germany
2 shared publications - Daniel Grüner
Institute of Energy Materials and Devices IMD-1, Forschungszentrum Jülich GmbH, Jülich 52425, NRW, Germany
1 shared publication
Latest Publications
- Open Access
- 17 March 2025
- Published by Elsevier in Corrosion Science
- Vol. 249
Effect of MgSO4 addition on alkali sulphates induced hot corrosion of a β-NiAl coating
- 17 March 2025
- Published by Elsevier in Corrosion Science
- Vol. 249
Open AccessEffect of MgSO4 addition on alkali sulphates induced hot corrosion of a β-NiAl coating
- Open Access
- 6 February 2020
- Published by Wiley in Advanced Engineering Materials
- Vol. 22 (6)
Role of Temperature in Na2SO4–K2SO4 Deposit Induced Type II Hot Corrosion of NiAl Coating on a Commercial Ni‐Based Superalloy
The life span of gas turbine coatings may be restricted by type II hot corrosion when exposed at elevated temperatures in aggressive environments during service. Herein, the temperature dependence of corrosion morphologies and kinetics of NiAl coating on a second‐generation single crystalline Ni‐based superalloy is studied to provide an insight into the possible corrosion mechanisms. A series of tests are performed at 600–800 °C in air‐300 ppm SO2 atmosphere with Na2SO4–20% K2SO4 salt mixture as deposit. Severe attack is observed at both 700 and 750 °C after 24 h exposure, whereas at 600 and 800 °C, only a minor attack is found. The results indicate that the corrosion rate is strongly governed by Na2SO4–NiSO4 liquid formation, and temperature affects the attack rate of the outer coating (mainly β‐NiAl phase) primarily by changing the required minimum SO3 partial pressure to stabilize this liquid. The influence of temperature and on phase equilibrium of the salt and oxide mixture is calculated with an in‐house developed thermodynamic database. The predicted minimum for liquid formation calculated with the database is consistent with the experimental results.
- 6 February 2020
- Published by Wiley in Advanced Engineering Materials
- Vol. 22 (6)
Open AccessRole of Temperature in Na2SO4–K2SO4 Deposit Induced Type II Hot Corrosion of NiAl Coating on a Commercial Ni‐Based Superalloy
The life span of gas turbine coatings may be restricted by type II hot corrosion when exposed at elevated temperatures in aggressive environments during service. Herein, the temperature dependence of corrosion morphologies and kinetics of NiAl coating on a second‐generation single crystalline Ni‐based superalloy is studied to provide an insight into the possible corrosion mechanisms. A series of tests are performed at 600–800 °C in air‐300 ppm SO2 atmosphere with Na2SO4–20% K2SO4 salt mixture as deposit. Severe attack is observed at both 700 and 750 °C after 24 h exposure, whereas at 600 and 800 °C, only a minor attack is found. The results indicate that the corrosion rate is strongly governed by Na2SO4–NiSO4 liquid formation, and temperature affects the attack rate of the outer coating (mainly β‐NiAl phase) primarily by changing the required minimum SO3 partial pressure to stabilize this liquid. The influence of temperature and on phase equilibrium of the salt and oxide mixture is calculated with an in‐house developed thermodynamic database. The predicted minimum for liquid formation calculated with the database is consistent with the experimental results.