Fengshan Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Fengshan Huang has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Ke Xu
Collaborative Innovation Center of Steel Technology, University of Science and Technology Beijing, Beijing 100083, China
2 shared publications - Fuxiang Zhang
School of Mechanical Engineering, Hebei University of Science & Technology, Shijiazhuang 050091, China
1 shared publication - Guanyi Zhang
State Key Laboratory of Chemical Resource Engineering, Beijing Advanced Innovation Center for Soft Matter Science and Engineering, Beijing University of Chemical Technology, Beijing 100029, P. R. China
1 shared publication Guoyang Zhang
State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology, Beijing, 100029, P. R. China
1 shared publication- Honghai Liu
Petrochemical Research Institute, Petrochina Company Limited, Beijing, 100195, P. R. China
1 shared publication - Hongtao Liu
State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology, Beijing, 100029, P. R. China
1 shared publication
Latest Publications
- 17 September 2026
- Published by Taylor & Francis in Nondestructive Testing and Evaluation
- p. 1-35
A practical non-contact layer thickness measurement method for two-layer clad plates using EMAR
1. Clad plates have been extensively studied over the past decades. They are produced by bonding one or more thin layers (cladding) of a material onto a dissimilar base metal to combine the advanta...
- 17 September 2026
- Published by Taylor & Francis in Nondestructive Testing and Evaluation
- p. 1-35
A practical non-contact layer thickness measurement method for two-layer clad plates using EMAR
1. Clad plates have been extensively studied over the past decades. They are produced by bonding one or more thin layers (cladding) of a material onto a dissimilar base metal to combine the advanta...
- 15 September 2026
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 55 (35) , 12898-12910
A facile synthesis strategy for Al-SBA-15 with a high density of acid sites via a neutral pathway for efficient hydrodeoxygenation of levulinic acid to γ-valerolactone
Al-SBA-15 with a high-density of acid sites was synthesized using an Al-Cit-assisted neutral synthesis strategy.
- 15 September 2026
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 55 (35) , 12898-12910
A facile synthesis strategy for Al-SBA-15 with a high density of acid sites via a neutral pathway for efficient hydrodeoxygenation of levulinic acid to γ-valerolactone
Al-SBA-15 with a high-density of acid sites was synthesized using an Al-Cit-assisted neutral synthesis strategy.
- Open Access
- 7 January 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (2) , 610
Calibration of Snow Particle Contact Parameters for Simulation Analysis of Membrane Structure Snow Removal Robot
To enhance the accuracy of discrete element method (DEM) simulation for the snow removal process performed by autonomous robots on membrane structures, this study calibrated the key contact parameters of snow particles used in the simulation. Through literature research, the intrinsic parameters and contact parameter ranges for snow particles and membrane structures were determined. A discrete element model of snow particles was established, and the Hertz–Mindlin with Johnson–Kendall–Robert contact model was selected to simulate the formation process of the repose angle. Using the actual repose angle of snow particles as the target, four significant factors were identified through the P-B experiment, and other factors were set at the intermediate level. Through the steepest slope climbing experiment and response surface design, second-order response equations of the four significant factors were obtained. The optimal parameter combination was calculated as follows: the surface energy of snow particles was 0.23 J/m2; the restitution coefficient, static friction coefficient, and rolling friction coefficient of snow–snow were 0.141, 0.05, and 0.03; and the restitution coefficient, static friction coefficient, and rolling friction coefficient of snow–membrane were 0.2, 0.18, and 0.03. The simulated repose angle was 40.62°, and the relative error with the actual repose angle was 0.32%. These calibration results are reliable and can provide a reliable simulation basis and essential data support for the optimal design of a snow removal robot and the dynamic simulation of the operation process.
- 7 January 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (2) , 610
Open AccessCalibration of Snow Particle Contact Parameters for Simulation Analysis of Membrane Structure Snow Removal Robot
To enhance the accuracy of discrete element method (DEM) simulation for the snow removal process performed by autonomous robots on membrane structures, this study calibrated the key contact parameters of snow particles used in the simulation. Through literature research, the intrinsic parameters and contact parameter ranges for snow particles and membrane structures were determined. A discrete element model of snow particles was established, and the Hertz–Mindlin with Johnson–Kendall–Robert contact model was selected to simulate the formation process of the repose angle. Using the actual repose angle of snow particles as the target, four significant factors were identified through the P-B experiment, and other factors were set at the intermediate level. Through the steepest slope climbing experiment and response surface design, second-order response equations of the four significant factors were obtained. The optimal parameter combination was calculated as follows: the surface energy of snow particles was 0.23 J/m2; the restitution coefficient, static friction coefficient, and rolling friction coefficient of snow–snow were 0.141, 0.05, and 0.03; and the restitution coefficient, static friction coefficient, and rolling friction coefficient of snow–membrane were 0.2, 0.18, and 0.03. The simulated repose angle was 40.62°, and the relative error with the actual repose angle was 0.32%. These calibration results are reliable and can provide a reliable simulation basis and essential data support for the optimal design of a snow removal robot and the dynamic simulation of the operation process.
- Open Access
Distributed Non-Fragile State Estimation for Uncertain Nonlinear Systems of Sensor Networks Subject to Sensor Nonlinearities
This paper studies the distributed state estimation issue of nonlinear dynamical systems with parameter uncertainties based on sensor networks under the non-fragile control framework. Moreover, all the sensors are in a fully distributed framework with information exchanges to reduce the communication and computation resources. In particular, the sensor nonlinearities in the sensor network and state estimation gain fluctuations are taken into account for more general applicability. With the help of the Lyapunov–Krasovskii approach, sufficient convex optimization criteria can be given so that the passivity performance of its resultant state estimation error system can be guaranteed. The optimized non-fragile state estimation gains can be further determined on the basis of solving the convex optimization. The advantages and usefulness of our developed results are finally demonstrated by two illustrative examples.
Open AccessDistributed Non-Fragile State Estimation for Uncertain Nonlinear Systems of Sensor Networks Subject to Sensor Nonlinearities
This paper studies the distributed state estimation issue of nonlinear dynamical systems with parameter uncertainties based on sensor networks under the non-fragile control framework. Moreover, all the sensors are in a fully distributed framework with information exchanges to reduce the communication and computation resources. In particular, the sensor nonlinearities in the sensor network and state estimation gain fluctuations are taken into account for more general applicability. With the help of the Lyapunov–Krasovskii approach, sufficient convex optimization criteria can be given so that the passivity performance of its resultant state estimation error system can be guaranteed. The optimized non-fragile state estimation gains can be further determined on the basis of solving the convex optimization. The advantages and usefulness of our developed results are finally demonstrated by two illustrative examples.