Ziyao Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ziyao Zhou has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Jiayang Pang
College of Water Resources and Civil Engineering, China Agricultural University 1 , Beijing 100083
3 shared publications - Kang Xu
Key Laboratory of Fluid and Power Machinery, Ministry of Education, Xihua University, Chengdu 610039, China
3 shared publications Pinyu Xiang
College of Water Resource & Hydropower Sichuan University Chengdu China
2 shared publicationsXiaobing Liu
Key Laboratory of Fluid and Power Machinery, Ministry of Education Xihua University Chengdu China
2 shared publications- Yuanyuan Gang
Key Laboratory of Fluid and Power Machinery, Ministry of Education, Xihua University 2 , Chengdu, Sichuan 610039
2 shared publications - Haiqi Wang
Key Laboratory of Fluid and Power Machinery, Ministry of Education Xihua University Chengdu China
1 shared publication
Latest Publications
- Open Access
- 26 May 2025
- Published by Wiley in Energy Science & Engineering
Solid–Liquid Flow Analysis of Francis‐99 Turbine Runner: Effects of Sediment Concentration
This study examines the behavior of solid–liquid two‐phase flow within the runner of the Francis‐99 turbine. Numerical simulations were carried out by Ansys Fluent software using the Mixture multiphase flow model along with the Realizable k‐ε turbulence model to analyze the solid–liquid two‐phase flow in the turbine runner. The sediment distribution on the turbine runner surface was evaluated for different sediment concentrations (SC = 500, 1500, 2500, 5000, 8000, and 11,500 ppm). The results indicate that sediment particles within the runner primarily adhere to the surfaces of the runner blades, displaying a uniform distribution. With increasing sediment concentration, the sediment volume fraction on the turbine blade surface rises significantly. The sediment distribution on both long and short blades exhibits similarity, with peak concentration observed at the trailing edge and mid‐sections of the blades. Additionally, the sediment volume fraction is greater on the pressure side of the blades than on the suction side. This study aims to expand the research on multiphase flow characteristics of the Francis‐99 turbine.
- 26 May 2025
- Published by Wiley in Energy Science & Engineering
Open AccessSolid–Liquid Flow Analysis of Francis‐99 Turbine Runner: Effects of Sediment Concentration
This study examines the behavior of solid–liquid two‐phase flow within the runner of the Francis‐99 turbine. Numerical simulations were carried out by Ansys Fluent software using the Mixture multiphase flow model along with the Realizable k‐ε turbulence model to analyze the solid–liquid two‐phase flow in the turbine runner. The sediment distribution on the turbine runner surface was evaluated for different sediment concentrations (SC = 500, 1500, 2500, 5000, 8000, and 11,500 ppm). The results indicate that sediment particles within the runner primarily adhere to the surfaces of the runner blades, displaying a uniform distribution. With increasing sediment concentration, the sediment volume fraction on the turbine blade surface rises significantly. The sediment distribution on both long and short blades exhibits similarity, with peak concentration observed at the trailing edge and mid‐sections of the blades. Additionally, the sediment volume fraction is greater on the pressure side of the blades than on the suction side. This study aims to expand the research on multiphase flow characteristics of the Francis‐99 turbine.
- Open Access
- 13 May 2025
- Published by Wiley in Energy Science & Engineering
- Vol. 13 (7) , 3753-3764
Effect of Sand Particle Size on Sand–Water Flow in a Francis‐99 Distributor
To examine the sand–water flow characteristics in the distributor of the Francis‐99 hydraulic turbine, numerical simulations were conducted using the Mixture multiphase flow model, focusing on the impact of varying sand particle sizes. The findings indicate that near‐wall velocities of sand and water in the fixed and guide vanes of the Francis‐99 hydraulic turbine range from 1.5 to 3.4 m/s and from 2.1 to 11.2 m/s, respectively, with the highest values observed at the tail section. The trajectories of smaller sand particles closely followed the water flow, whereas for particle sizes of around 0.3 mm, acceleration and deceleration processes showed a noticeable lag due to inertia, leading to significant velocity fluctuations compared to smaller particles. The sediment concentration on the front side of the stay and guide vanes initially increased and then decreased along the flow direction, whereas on the back side, a gradual reduction was observed, with the peak sediment concentration occurring at the head. As the sand particle size increased, the uniformity of the sediment concentration distribution on the guide vane surface decreased. When the average sediment concentration (volume fraction) in the flow field was 0.00095, the maximum concentration on the front side of the guide vane reached 0.0025, and the region of high concentration expanded, whereas the back side showed an opposite trend. The results further demonstrate that the arrangement of fixed and guide vanes influences the sediment concentration distribution in the sand–water flow within the hydraulic guide mechanism of the Francis‐99 hydraulic turbine, leading to inconsistencies in sediment distribution patterns on adjacent guide vane surfaces.
- 13 May 2025
- Published by Wiley in Energy Science & Engineering
- Vol. 13 (7) , 3753-3764
Open AccessEffect of Sand Particle Size on Sand–Water Flow in a Francis‐99 Distributor
To examine the sand–water flow characteristics in the distributor of the Francis‐99 hydraulic turbine, numerical simulations were conducted using the Mixture multiphase flow model, focusing on the impact of varying sand particle sizes. The findings indicate that near‐wall velocities of sand and water in the fixed and guide vanes of the Francis‐99 hydraulic turbine range from 1.5 to 3.4 m/s and from 2.1 to 11.2 m/s, respectively, with the highest values observed at the tail section. The trajectories of smaller sand particles closely followed the water flow, whereas for particle sizes of around 0.3 mm, acceleration and deceleration processes showed a noticeable lag due to inertia, leading to significant velocity fluctuations compared to smaller particles. The sediment concentration on the front side of the stay and guide vanes initially increased and then decreased along the flow direction, whereas on the back side, a gradual reduction was observed, with the peak sediment concentration occurring at the head. As the sand particle size increased, the uniformity of the sediment concentration distribution on the guide vane surface decreased. When the average sediment concentration (volume fraction) in the flow field was 0.00095, the maximum concentration on the front side of the guide vane reached 0.0025, and the region of high concentration expanded, whereas the back side showed an opposite trend. The results further demonstrate that the arrangement of fixed and guide vanes influences the sediment concentration distribution in the sand–water flow within the hydraulic guide mechanism of the Francis‐99 hydraulic turbine, leading to inconsistencies in sediment distribution patterns on adjacent guide vane surfaces.
- 1 March 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (3)
Design of a single-channel wear test device for the Francis-99 turbine guide mechanism and sediment wear testing
This study employed a design method for a single-channel sediment wear test device based on numerical simulation and the principle of similarity to investigate the characteristics of solid–liquid two-phase flow and the sediment wear mechanism of the Francis-99 turbine under sand-containing conditions. The design of the test device and the sediment wear tests for the diversion components of the Francis-99 turbine were conducted, and the similarity of the flow field was validated. The findings indicate that under the design conditions of the single-channel sediment wear test device and the prototype, the surface sediment particle velocity range for the stay vane is 1.4–1.8 m/s, while that for the guide vane is 1.1–6.2 m/s. The sediment particle velocity difference near the wall is about 0.02 m/s, and the sediment distribution pattern is relatively similar. The difference in the impact angle of sediment particles at the heads of the stay vane and guide vane is about 0.1°. The wear rate on the stay vane surface ranges from 0.1 to 0.4 μm/h, and on the active guide vane surface, it ranges from 0.1 to 0.55 μm/h, with the maximum wear rate occurring near the tail area. The single-channel sediment wear test device described in this paper effectively reveals the wear mechanism of hydraulic turbine diversion components and demonstrates high feasibility.
- 1 March 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (3)
Design of a single-channel wear test device for the Francis-99 turbine guide mechanism and sediment wear testing
This study employed a design method for a single-channel sediment wear test device based on numerical simulation and the principle of similarity to investigate the characteristics of solid–liquid two-phase flow and the sediment wear mechanism of the Francis-99 turbine under sand-containing conditions. The design of the test device and the sediment wear tests for the diversion components of the Francis-99 turbine were conducted, and the similarity of the flow field was validated. The findings indicate that under the design conditions of the single-channel sediment wear test device and the prototype, the surface sediment particle velocity range for the stay vane is 1.4–1.8 m/s, while that for the guide vane is 1.1–6.2 m/s. The sediment particle velocity difference near the wall is about 0.02 m/s, and the sediment distribution pattern is relatively similar. The difference in the impact angle of sediment particles at the heads of the stay vane and guide vane is about 0.1°. The wear rate on the stay vane surface ranges from 0.1 to 0.4 μm/h, and on the active guide vane surface, it ranges from 0.1 to 0.55 μm/h, with the maximum wear rate occurring near the tail area. The single-channel sediment wear test device described in this paper effectively reveals the wear mechanism of hydraulic turbine diversion components and demonstrates high feasibility.