Pepie Tsolka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Pepie Tsolka has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Aristidis Galiatsatos
Division of Dental Technology Department of Biomedical Sciences University of West Attica Athens Greece
2 shared publications - Konstantinos Dimitriadis
Division of Dental Technology, Department of Biomedical Sciences, University of West Attica, 122 43 Athens, Greece
2 shared publications - Michael Nikolopoulos
Division of Dental Technology Department of Biomedical Sciences University of West Attica Athens Greece
2 shared publications - Stavros Yannikakis
Division of Dental Technology Department of Biomedical Sciences University of West Attica Athens Greece
2 shared publications - Athanasios Konstantinou Sfikas
Faculty of Engineering and Environment, Northumbria University, Newcastle upon Tyne NE1 8ST, UK
1 shared publication
Latest Publications
- Open Access
- 17 July 2025
- Published by Wiley in European Journal of Oral Sciences
- Vol. 133 (5) , e70031
Implant‐cemented Co–Cr frameworks produced by hard and soft milling: The impact of porcelain firing cycles on microstructure and fit accuracy
This study examines how porcelain firing cycles and fabrication methods impact the microstructure and the marginal and internal fit of implant‐cemented Co–Cr frameworks. Two fabrication processes for Co–Cr specimens were used: hard milling or soft milling. Each type of framework was then allocated to use either as‐fabricated or as porcelain‐fired. The microstructural analysis employed x‐ray diffraction (XRD) and scanning electron microscopy with energy‐dispersive x‐ray spectroscopy (SEM/EDX). A total of ten Co–Cr frameworks were fabricated for each method, and discrepancies in margin and internal fit were evaluated using X‐ray microtomography (micro‐CT) before and after the porcelain firing. Statistical analysis was performed using two‐way ANOVA and Tukey's multiple comparison tests (α = 0.05). The findings indicated a combination of γ‐fcc and ε‐hcp cobalt‐based phases, with porcelain firing notably enhancing the ε‐Co content, particularly among soft milled specimens. Soft milled specimens exhibited a diffuse presence of pores, while hard milled specimens revealed a random distribution of small pores. The soft milled specimens exhibited a significant reduction in discrepancies after the application of firing cycles. Although not statistically significant, the hard milled specimens also showed a trend toward reduced discrepancies post‐firing. All subgroups maintained clinically acceptable marginal adaptation, with soft milled frameworks outperforming their hard milled counterparts in overall fit.
- 17 July 2025
- Published by Wiley in European Journal of Oral Sciences
- Vol. 133 (5) , e70031
Open AccessImplant‐cemented Co–Cr frameworks produced by hard and soft milling: The impact of porcelain firing cycles on microstructure and fit accuracy
This study examines how porcelain firing cycles and fabrication methods impact the microstructure and the marginal and internal fit of implant‐cemented Co–Cr frameworks. Two fabrication processes for Co–Cr specimens were used: hard milling or soft milling. Each type of framework was then allocated to use either as‐fabricated or as porcelain‐fired. The microstructural analysis employed x‐ray diffraction (XRD) and scanning electron microscopy with energy‐dispersive x‐ray spectroscopy (SEM/EDX). A total of ten Co–Cr frameworks were fabricated for each method, and discrepancies in margin and internal fit were evaluated using X‐ray microtomography (micro‐CT) before and after the porcelain firing. Statistical analysis was performed using two‐way ANOVA and Tukey's multiple comparison tests (α = 0.05). The findings indicated a combination of γ‐fcc and ε‐hcp cobalt‐based phases, with porcelain firing notably enhancing the ε‐Co content, particularly among soft milled specimens. Soft milled specimens exhibited a diffuse presence of pores, while hard milled specimens revealed a random distribution of small pores. The soft milled specimens exhibited a significant reduction in discrepancies after the application of firing cycles. Although not statistically significant, the hard milled specimens also showed a trend toward reduced discrepancies post‐firing. All subgroups maintained clinically acceptable marginal adaptation, with soft milled frameworks outperforming their hard milled counterparts in overall fit.
- Open Access
- 17 March 2025
- Published by Wiley in European Journal of Oral Sciences
- Vol. 133 (3) , e70009
Influence of repeated porcelain firing cycles on the microstructure, marginal and internal fit of implant‐cemented Co‐Cr frameworks
This study investigated the effect of porcelain firing cycles and fabrication techniques on the microstructure, marginal, and internal fit of implant‐cemented cobalt‐chromium alloys (Co‐Cr) frameworks. Two groups of Co‐Cr specimens were prepared: one using selective laser melting (SLM) and the other through the lost wax‐casting technique (C). Each group was further divided into two subgroups: as‐manufactured and porcelain‐fired specimens. The microstructure was analyzed using x‐ray diffraction (XRD) and scanning electron microscopy with energy‐dispersive x‐ray spectroscopy (SEM/EDX). Ten Co‐Cr frameworks per manufacturing technique were fabricated, with marginal and internal discrepancies measured using micro‐CT before and after the firing cycles. The results were analyzed by two‐way ANOVA and Tukey multiple‐comparison tests. The results showed a mixed microstructure of γ‐fcc and ε‐hcp cobalt‐based phases, with porcelain firings increasing ε‐Co content, especially in group C. The C specimens exhibited distribution of small pores, while no pores/defects were found in the SLM group. The SLM group, although not at a statistically significant level, showed reduced marginal and internal discrepancy values after firings. In the same behavior pattern, the C group exhibited statistically significantly lower discrepancy values. Ultimately, all subgroups demonstrated clinically acceptable marginal adaptation, but the SLM frameworks exhibited superior marginal and internal fit which remained unaffected by the firing cycles.
- 17 March 2025
- Published by Wiley in European Journal of Oral Sciences
- Vol. 133 (3) , e70009
Open AccessInfluence of repeated porcelain firing cycles on the microstructure, marginal and internal fit of implant‐cemented Co‐Cr frameworks
This study investigated the effect of porcelain firing cycles and fabrication techniques on the microstructure, marginal, and internal fit of implant‐cemented cobalt‐chromium alloys (Co‐Cr) frameworks. Two groups of Co‐Cr specimens were prepared: one using selective laser melting (SLM) and the other through the lost wax‐casting technique (C). Each group was further divided into two subgroups: as‐manufactured and porcelain‐fired specimens. The microstructure was analyzed using x‐ray diffraction (XRD) and scanning electron microscopy with energy‐dispersive x‐ray spectroscopy (SEM/EDX). Ten Co‐Cr frameworks per manufacturing technique were fabricated, with marginal and internal discrepancies measured using micro‐CT before and after the firing cycles. The results were analyzed by two‐way ANOVA and Tukey multiple‐comparison tests. The results showed a mixed microstructure of γ‐fcc and ε‐hcp cobalt‐based phases, with porcelain firings increasing ε‐Co content, especially in group C. The C specimens exhibited distribution of small pores, while no pores/defects were found in the SLM group. The SLM group, although not at a statistically significant level, showed reduced marginal and internal discrepancy values after firings. In the same behavior pattern, the C group exhibited statistically significantly lower discrepancy values. Ultimately, all subgroups demonstrated clinically acceptable marginal adaptation, but the SLM frameworks exhibited superior marginal and internal fit which remained unaffected by the firing cycles.