Hiroshi Kinoshita
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Hiroshi Kinoshita has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
Serina Tanaka
3 shared publicationsYoshiyuki Sugai
3 shared publicationsNaohiro Matsumoto
Department of Mechanical Engineering, Graduate School of Engineering, University of Hyogo
2 shared publicationsA. G. Sokolsky
R.Branham (Argentina), C.Edelman (France), L. El Bakali (Morocco), Z
1 shared publicationAi Hamano
1 shared publicationAndré Deprit
R.Branham (Argentina), C.Edelman (France), L. El Bakali (Morocco), Z
1 shared publication
Latest Publications
- Open Access
- 18 August 2026
- Published by Elsevier in Tribology International
- Vol. 226
Offset linear relationship between friction force and optically detected contact area during dry sliding of polyacetal ball against glass disk
- 18 August 2026
- Published by Elsevier in Tribology International
- Vol. 226
Open AccessOffset linear relationship between friction force and optically detected contact area during dry sliding of polyacetal ball against glass disk
- 18 December 2025
- Published by Elsevier in Tribology International
- Vol. 216
Experimental and theoretical study on adsorption and reaction behavior of phosphorus antiwear and sulfur extreme pressure additives
- 18 December 2025
- Published by Elsevier in Tribology International
- Vol. 216
Experimental and theoretical study on adsorption and reaction behavior of phosphorus antiwear and sulfur extreme pressure additives
- Open Access
- 31 October 2025
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 20 (4) , 206-211
Identification of Regions Contributing to Friction Forces from Top-View In-Situ SEM Images of Friction Interfaces and Generation of Fake SEM Images of Friction Interfaces Using Deep Learning
Top-view in-situ scanning electron microscopy (SEM) images of the friction interfaces between an electron-transparent film and a polyacetal (POM) pin surface revealed the formation of transfer layers, wear debris (including rolling debris), and freestanding layers; however, the relationship between these phenomena and friction forces remains unclear. In this study, friction forces were estimated from SEM images using a convolutional neural network (CNN). The estimated friction forces closely matched the measured values. The specific regions in the SEM images that contributed to CNN friction force estimation were identified using gradient-weighted class activation mapping (Grad-CAM). These regions were primarily located around the contact surface rather than on the contact surface. Furthermore, to investigate the specific contact surface features associated with lower and higher friction forces beyond those observed in the friction test, fake top-view in-situ SEM images were generated with continuous and arbitrary friction forces, including values outside the experimental friction force range, using a continuous conditional generative adversarial network. The generated SEM images successfully reproduced the experimental features corresponding to the friction forces within a range for which sufficient experimental data were available.
- 31 October 2025
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 20 (4) , 206-211
Open AccessIdentification of Regions Contributing to Friction Forces from Top-View In-Situ SEM Images of Friction Interfaces and Generation of Fake SEM Images of Friction Interfaces Using Deep Learning
Top-view in-situ scanning electron microscopy (SEM) images of the friction interfaces between an electron-transparent film and a polyacetal (POM) pin surface revealed the formation of transfer layers, wear debris (including rolling debris), and freestanding layers; however, the relationship between these phenomena and friction forces remains unclear. In this study, friction forces were estimated from SEM images using a convolutional neural network (CNN). The estimated friction forces closely matched the measured values. The specific regions in the SEM images that contributed to CNN friction force estimation were identified using gradient-weighted class activation mapping (Grad-CAM). These regions were primarily located around the contact surface rather than on the contact surface. Furthermore, to investigate the specific contact surface features associated with lower and higher friction forces beyond those observed in the friction test, fake top-view in-situ SEM images were generated with continuous and arbitrary friction forces, including values outside the experimental friction force range, using a continuous conditional generative adversarial network. The generated SEM images successfully reproduced the experimental features corresponding to the friction forces within a range for which sufficient experimental data were available.
- Open Access
- 4 November 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (45) , 40983-40989
Low Friction of Graphene Oxide Aggregates in Lubricant Oil between a Steel Ball and Glass Disk under Boundary Lubrication
Previously, isolated nanocarbons in lubricating oils were considered essential for good lubrication. However, we observed that graphene oxide (GO) aggregates in lubricating oil have lower frictional properties than isolated dispersed GO. The GO was dispersed in polyα-olefin (PAO) using alkylamine at different ratios of GO and alkylamine, or it was heated at different temperatures to synthesize high- and low-dispersible GO-dispersed PAO. X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), and Raman spectroscopy measurements showed that low-dispersible modified GOs retained many of the original GO chemical and structural features. Macrotribological tests between a steel ball and glass disk in GO-dispersed oil were conducted with a load of 5 N under boundary lubrication. The friction interface was observed in situ using an optical microscope. In the low-dispersible GO-dispersed PAO, many GO aggregates were observed through optical microscopy. Surprisingly, the friction coefficients decreased when the GO aggregates entered the friction interface and covered the contact area. The low-dispersible GO-dispersed PAO using alkylamine had the lowest friction coefficient of 0.05, as the GO aggregates covered the contact area. From microtribological tests with a load of 0.8 mN as well, it is assumed that the low friction of the GO aggregates originates due to the sliding between the weakest shear layers in the aligned multiple GO layers.
- 4 November 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (45) , 40983-40989
Open AccessLow Friction of Graphene Oxide Aggregates in Lubricant Oil between a Steel Ball and Glass Disk under Boundary Lubrication
Previously, isolated nanocarbons in lubricating oils were considered essential for good lubrication. However, we observed that graphene oxide (GO) aggregates in lubricating oil have lower frictional properties than isolated dispersed GO. The GO was dispersed in polyα-olefin (PAO) using alkylamine at different ratios of GO and alkylamine, or it was heated at different temperatures to synthesize high- and low-dispersible GO-dispersed PAO. X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), and Raman spectroscopy measurements showed that low-dispersible modified GOs retained many of the original GO chemical and structural features. Macrotribological tests between a steel ball and glass disk in GO-dispersed oil were conducted with a load of 5 N under boundary lubrication. The friction interface was observed in situ using an optical microscope. In the low-dispersible GO-dispersed PAO, many GO aggregates were observed through optical microscopy. Surprisingly, the friction coefficients decreased when the GO aggregates entered the friction interface and covered the contact area. The low-dispersible GO-dispersed PAO using alkylamine had the lowest friction coefficient of 0.05, as the GO aggregates covered the contact area. From microtribological tests with a load of 0.8 mN as well, it is assumed that the low friction of the GO aggregates originates due to the sliding between the weakest shear layers in the aligned multiple GO layers.
- Open Access
- 22 June 2020
- Published by Springer Nature in Scientific Reports
- Vol. 10 (1) , 1-9
Formation of large area closely packed carbon onions film by plasma-based ion implantation
A substantial quantity of carbon onions in a durable film state is indispensable for its applications. In this study, large area fabrication of closely packed homogeneous carbon onion nanoparticle film using plasma-based ion implantation was demonstrated. Ag film deposited on a Si substrate was used as the implantation target for the hydrocarbon ions accelerated at 20 kV. Nanoparticles with the mean diameter of 7.5 nm were formed at the grain boundary of the Ag film. Carbon onions with the mean diameter of 17.4 nm were synthesized and arranged to a closely packed nanoparticle film with the thickness of around 200 nm by gradual thermal vaporization of the Ag. The closely packed configuration was achieved due to the isolated growth of carbon onion nanoparticle and high uniformity of the diameter. This process can be used in principle large area formation compered to typical ion implantation technique of carbon onion nanoparticle film, which can be applicable for the practical use in mechanical and electrochemical applications.
- 22 June 2020
- Published by Springer Nature in Scientific Reports
- Vol. 10 (1) , 1-9
Open AccessFormation of large area closely packed carbon onions film by plasma-based ion implantation
A substantial quantity of carbon onions in a durable film state is indispensable for its applications. In this study, large area fabrication of closely packed homogeneous carbon onion nanoparticle film using plasma-based ion implantation was demonstrated. Ag film deposited on a Si substrate was used as the implantation target for the hydrocarbon ions accelerated at 20 kV. Nanoparticles with the mean diameter of 7.5 nm were formed at the grain boundary of the Ag film. Carbon onions with the mean diameter of 17.4 nm were synthesized and arranged to a closely packed nanoparticle film with the thickness of around 200 nm by gradual thermal vaporization of the Ag. The closely packed configuration was achieved due to the isolated growth of carbon onion nanoparticle and high uniformity of the diameter. This process can be used in principle large area formation compered to typical ion implantation technique of carbon onion nanoparticle film, which can be applicable for the practical use in mechanical and electrochemical applications.
- 1 October 2011
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 417 (1-3) , 1018-1021
Effects of multi-beam irradiation on defect formation in Fe–Cr alloys
- 1 October 2011
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 417 (1-3) , 1018-1021
Effects of multi-beam irradiation on defect formation in Fe–Cr alloys
- Open Access
- 1 January 2010
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series C
- Vol. 76 (766) , 1617-1626
The Square Cup Deep Drawing by Variable Blank Holder Force(Machine Elements, Design and Manufacturing)
In the deep drawing, the low blank holder force (BHF) will cause the wrinkle, while the high BHF will result in the tearing. Therefore it is important to determine the appropriate BHF in the forming. In this paper, the variable blank holder force (VBHF) approach for the deep drawing is employed. The simple closed-type algorithm is developed to obtain the VBHF trajectory. The proposed algorithm is roughly divided into two phases. The objective of first phase is to check the wrinkle and the tearing. In this phase, the low BHF, which causes the wrinkle, is used as the initial BHF. The BHF is increased in order to avoid the wrinkle. The algorithm will be terminated when the tearing occurs. The distance between the die and the blank holder is used to measure the wrinkle. Then, the second phase is considered. The main objective of second phase is to examine the thickness deviations. It is expected that the BHF will be decreased by considering the thickness deviation. The wrinkle is also checked in the second phase. By iterating above two phases, the VBHF trajectory can be obtained. One of the advantages by the VBHF is to reduce the forming energy. The validity is examined through the numerical simulation and experiment.
- 1 January 2010
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series C
- Vol. 76 (766) , 1617-1626
Open AccessThe Square Cup Deep Drawing by Variable Blank Holder Force(Machine Elements, Design and Manufacturing)
In the deep drawing, the low blank holder force (BHF) will cause the wrinkle, while the high BHF will result in the tearing. Therefore it is important to determine the appropriate BHF in the forming. In this paper, the variable blank holder force (VBHF) approach for the deep drawing is employed. The simple closed-type algorithm is developed to obtain the VBHF trajectory. The proposed algorithm is roughly divided into two phases. The objective of first phase is to check the wrinkle and the tearing. In this phase, the low BHF, which causes the wrinkle, is used as the initial BHF. The BHF is increased in order to avoid the wrinkle. The algorithm will be terminated when the tearing occurs. The distance between the die and the blank holder is used to measure the wrinkle. Then, the second phase is considered. The main objective of second phase is to examine the thickness deviations. It is expected that the BHF will be decreased by considering the thickness deviation. The wrinkle is also checked in the second phase. By iterating above two phases, the VBHF trajectory can be obtained. One of the advantages by the VBHF is to reduce the forming energy. The validity is examined through the numerical simulation and experiment.
- 1 April 2007
- Published by Elsevier in Diamond and Related Materials
- Vol. 16 (4-7) , 1179-1182
Atomic structure and field evaporation of carbon nanotube studied by atom probe field ion microscopy
- 1 April 2007
- Published by Elsevier in Diamond and Related Materials
- Vol. 16 (4-7) , 1179-1182
Atomic structure and field evaporation of carbon nanotube studied by atom probe field ion microscopy