Tianqi Hu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Tianqi Hu has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Hongtao Chen
Department of Materials Science and Engineering, Shenzhen Graduate School, Harbin Institute of Technology, Shenzhen, China
4 shared publicationsMingyu Li
Department of Materials Science and Engineering, Shenzhen Graduate School, Harbin Institute of Technology, Shenzhen, China
3 shared publications- Chunqing Wang
State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001, China
2 shared publications - Angela Papa
INFN Sezione di Pisa, Largo Bruno Pontecorvo, 3, 56127, Pisa, Italy
1 shared publication - Chavdar Dutsov
Faculty of Physics, Sofia University “St. Kliment Ohridski”, Sofia, Bulgaria
1 shared publication - David Höhl
Paul Scherrer Institute (PSI)
1 shared publication
Latest Publications
- Open Access
- 31 July 2026
- Published by Springer Nature in The European Physical Journal C
- Vol. 86 (7) , 911
Construction and characterization of a muon trigger detector for the PSI muEDM experiment
We present the upgraded design, construction, and beam test results for the muon trigger detector (MTD) developed for the muon electric dipole moment (muEDM) experiment at the Paul Scherrer Institute (PSI) in Switzerland. This experiment aims to improve the sensitivity of the muon EDM measurement by more than three orders of magnitude beyond the current limit established by the BNL Muon $$g-2$$ experiment. Precise identification of storable incoming muons at the entrance of the storage solenoid is essential, as the MTD must rapidly trigger a pulsed magnetic kicker to confine muons in the central region of the solenoid, where a weakly focusing magnetic field is maintained. The MTD comprises two subsystems: a 0.1 mm-thick plastic scintillator “gate detector” read out by four silicon photomultipliers (SiPMs), and a 5 mm-thick CNC-machined plastic scintillator “active aperture detector” read out by six SiPMs. The geometry of the active aperture detector was optimized through acceptance studies to maximize both storage efficiency and background veto efficiency. Integrated fast electronics generate an LVTTL trigger signal under an anti-coincidence condition – a muon detected in the gate but not in the aperture – ensuring selective triggering of storable muon events for the EDM measurement. The system was tested at the PSI $$\pi $$ E1 beamline using 22.5 MeV/ c muons under scaled-down conditions to characterize detector response and trigger performance. A Geant4 simulation incorporating detailed optical photon transport and SiPM response modeling was developed and reproduces the measured event topologies with $${\sim }97\%$$ agreement. These results validate the detector design and demonstrate the MTD’s readiness for deployment in the full muEDM Phase-1 setup.- 31 July 2026
- Published by Springer Nature in The European Physical Journal C
- Vol. 86 (7) , 911
Open AccessConstruction and characterization of a muon trigger detector for the PSI muEDM experiment
We present the upgraded design, construction, and beam test results for the muon trigger detector (MTD) developed for the muon electric dipole moment (muEDM) experiment at the Paul Scherrer Institute (PSI) in Switzerland. This experiment aims to improve the sensitivity of the muon EDM measurement by more than three orders of magnitude beyond the current limit established by the BNL Muon $$g-2$$ experiment. Precise identification of storable incoming muons at the entrance of the storage solenoid is essential, as the MTD must rapidly trigger a pulsed magnetic kicker to confine muons in the central region of the solenoid, where a weakly focusing magnetic field is maintained. The MTD comprises two subsystems: a 0.1 mm-thick plastic scintillator “gate detector” read out by four silicon photomultipliers (SiPMs), and a 5 mm-thick CNC-machined plastic scintillator “active aperture detector” read out by six SiPMs. The geometry of the active aperture detector was optimized through acceptance studies to maximize both storage efficiency and background veto efficiency. Integrated fast electronics generate an LVTTL trigger signal under an anti-coincidence condition – a muon detected in the gate but not in the aperture – ensuring selective triggering of storable muon events for the EDM measurement. The system was tested at the PSI $$\pi $$ E1 beamline using 22.5 MeV/ c muons under scaled-down conditions to characterize detector response and trigger performance. A Geant4 simulation incorporating detailed optical photon transport and SiPM response modeling was developed and reproduces the measured event topologies with $${\sim }97\%$$ agreement. These results validate the detector design and demonstrate the MTD’s readiness for deployment in the full muEDM Phase-1 setup. - 1 October 2017
- Published by Elsevier in Materials & Design
- Vol. 131, 196-203
Microstructure evolution and thermostability of bondline based on Cu@Sn core-shell structured microparticles under high-temperature conditions
- 1 October 2017
- Published by Elsevier in Materials & Design
- Vol. 131, 196-203
Microstructure evolution and thermostability of bondline based on Cu@Sn core-shell structured microparticles under high-temperature conditions
- 1 June 2017
- Published by Elsevier in Surface and Coatings Technology
- Vol. 319, 230-240
Study of electroless Sn-coated Cu microparticles and their application as a high temperature thermal interface material
- 1 June 2017
- Published by Elsevier in Surface and Coatings Technology
- Vol. 319, 230-240
Study of electroless Sn-coated Cu microparticles and their application as a high temperature thermal interface material
- 1 October 2016
- Published by Elsevier in Materials & Design
- Vol. 108, 383-390
Die attach materials with high remelting temperatures created by bonding Cu@Sn microparticles at lower temperatures
- 1 October 2016
- Published by Elsevier in Materials & Design
- Vol. 108, 383-390
Die attach materials with high remelting temperatures created by bonding Cu@Sn microparticles at lower temperatures
- 26 February 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 32 (1) , 441-451
Cu@Sn Core–Shell Structure Powder Preform for High-Temperature Applications Based on Transient Liquid Phase Bonding
This paper presents a novel die-attach material for high-temperature applications based on transient liquid phase (TLP) bonding. Cu particles are electroless plated with Sn to achieve Cu@Sn structure, and the fabricated Cu@Sn particles are compressed into preforms for die attachment. This material can be reflowed at a low temperature (<260 °C) due to the low melting temperature of the outer Sn layer. However, after reflow soldering, the resulting interconnections can withstand a high temperature of at least 415 °C, with the entire outer Sn layer transforming into Cu−Sn intermetallic compounds (IMCs) with high remelting temperatures. The formed bondlines exhibit good electrical and thermal conductivity due to the low porosity and the embedded Cu particles in the interconnections. A large shear strength at 400 °C can be achieved with the high-remelting Cu−Sn IMCs in the interconnections. Furthermore, the interconnections also exhibit excellent reliability under thermal shock cycling from −55 to 200 °C. The I – V curve and breakdown voltages of the novel preform-bonded IGBTs are measured to examine the interconnection quality compared with those of Cu−Sn TLP-bonded IGBTs. This die-attach material is suitable for power devices operating under high temperatures or other harsh environments.
- 26 February 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 32 (1) , 441-451
Cu@Sn Core–Shell Structure Powder Preform for High-Temperature Applications Based on Transient Liquid Phase Bonding
This paper presents a novel die-attach material for high-temperature applications based on transient liquid phase (TLP) bonding. Cu particles are electroless plated with Sn to achieve Cu@Sn structure, and the fabricated Cu@Sn particles are compressed into preforms for die attachment. This material can be reflowed at a low temperature (<260 °C) due to the low melting temperature of the outer Sn layer. However, after reflow soldering, the resulting interconnections can withstand a high temperature of at least 415 °C, with the entire outer Sn layer transforming into Cu−Sn intermetallic compounds (IMCs) with high remelting temperatures. The formed bondlines exhibit good electrical and thermal conductivity due to the low porosity and the embedded Cu particles in the interconnections. A large shear strength at 400 °C can be achieved with the high-remelting Cu−Sn IMCs in the interconnections. Furthermore, the interconnections also exhibit excellent reliability under thermal shock cycling from −55 to 200 °C. The I – V curve and breakdown voltages of the novel preform-bonded IGBTs are measured to examine the interconnection quality compared with those of Cu−Sn TLP-bonded IGBTs. This die-attach material is suitable for power devices operating under high temperatures or other harsh environments.