Sukan Kara
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sukan Kara has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Erdem Özdemir
Private Practice, Özdemir Dental Center, Antalya 07160, Turkey
2 shared publications - Fehmi Gönüldaş
Department of Prosthodontics, Ankara University Faculty of Dentistry, Ankara, Türkiye
2 shared publications - Hakan Aydın
Antalya Bilim University
2 shared publications - Kerem Yılmaz
Department of Prosthodontics, Faculty of Dentistry, Antalya Bilim University, 07190 Antalya, Turkey
2 shared publications - Zeynep Bilen
Department of Prosthodontics, Faculty of Dentistry, Ankara University, Ankara 06560, Turkey
2 shared publications - Özge Çiloğlu
Bilimdent Oral and Dental Health Center, Antalya Bilim University, 07190 Antalya, Turkey
2 shared publications
Latest Publications
- Open Access
Effect of Pulpal Base, Restorative Material, and Preparation Type on Marginal and Internal Fit and Fracture Strength of Endocrowns
The aim of this innovative study was to investigate the feasibility of a modified butt joint preparation with two grooves instead of a ferrule when root dentin tissue is limited in mandibular molars. It was also investigated to what extent the effect of these treatment options on marginal and internal fit and fracture strength (FS) varied according to the type of material and whether or not a fiber ribbon was used at the base. Marginal and internal fit were evaluated using the triple-scan protocol. Statistical analysis was conducted via a three-way analysis of variance (ANOVA). The absolute marginal discrepancy (AMD), marginal discrepancy, and overall fit values for the ceramic group were 127 μm, 108 μm, and 120 μm, respectively, while corresponding values for the hybrid ceramic group were 139 μm, 116 μm, and 130 μm (p < 0.05). The mean FS recorded for ceramic restorations was 662 N, whereas hybrid ceramic restorations demonstrated a significantly higher FS of 903 N (p < 0.001). When material type was assessed independently of preparation design and base configuration, both ceramic and hybrid ceramic exceeded the predefined clinical acceptability threshold for AMD; however, they remained within acceptable limits for the remaining parameters. Among the evaluated configurations, hybrid ceramic restorations incorporating ferrules and fiber-reinforced bases exhibited the highest FS values, whereas ceramic restorations with modified biological widths and lacking fiber reinforcement yielded the lowest FS values.
Open AccessEffect of Pulpal Base, Restorative Material, and Preparation Type on Marginal and Internal Fit and Fracture Strength of Endocrowns
The aim of this innovative study was to investigate the feasibility of a modified butt joint preparation with two grooves instead of a ferrule when root dentin tissue is limited in mandibular molars. It was also investigated to what extent the effect of these treatment options on marginal and internal fit and fracture strength (FS) varied according to the type of material and whether or not a fiber ribbon was used at the base. Marginal and internal fit were evaluated using the triple-scan protocol. Statistical analysis was conducted via a three-way analysis of variance (ANOVA). The absolute marginal discrepancy (AMD), marginal discrepancy, and overall fit values for the ceramic group were 127 μm, 108 μm, and 120 μm, respectively, while corresponding values for the hybrid ceramic group were 139 μm, 116 μm, and 130 μm (p < 0.05). The mean FS recorded for ceramic restorations was 662 N, whereas hybrid ceramic restorations demonstrated a significantly higher FS of 903 N (p < 0.001). When material type was assessed independently of preparation design and base configuration, both ceramic and hybrid ceramic exceeded the predefined clinical acceptability threshold for AMD; however, they remained within acceptable limits for the remaining parameters. Among the evaluated configurations, hybrid ceramic restorations incorporating ferrules and fiber-reinforced bases exhibited the highest FS values, whereas ceramic restorations with modified biological widths and lacking fiber reinforcement yielded the lowest FS values.
- Open Access
- 3 April 2025
- Published by MDPI AG in Preprints.org
Effect of Pulpal Base, Restorative Material and Preparation Type on Marginal and Internal Fit and Fracture Strength of Endocrowns
The aim of this study was to investigate the effect of base material, restorative material and finish line on marginal and internal fit and fracture strength (FS) of endocrowns (N = 64). The restorative materials were ceramic and hybrid ceramic, the preparations were ferrule and modified butt joint (BJ) with two grooves, and the bases were with and without fiber ribbon. Marginal and internal fit were assessed using the triple scan. Statistical analyses were performed using three-way ANOVA. The absolute marginal discrepancy (AMD), marginal discrepancy and overall fit values obtained for ceramic were 127 µm, 108 µm and 120 µm, whereas those obtained for hybrid ceramic were 139 µm, 116 µm and 130 µm, respectively (p < 0.05). The overall FS obtained for ceramic was 662 N, whereas that for hybrid ceramic was 903 N (p < 0.001). When the material was evaluated regardless of preparation and base, ceramic and hybrid ceramic exceeded the selected clinical acceptability threshold for AMD, but did not exceed it for other parameters. Hybrid ceramic restorations with ferrules and fiber bases tended to provide the highest FS, whereas ceramic restorations with modified BJs and without fiber bases tended to provide the lowest FS.
- 3 April 2025
- Published by MDPI AG in Preprints.org
Open AccessEffect of Pulpal Base, Restorative Material and Preparation Type on Marginal and Internal Fit and Fracture Strength of Endocrowns
The aim of this study was to investigate the effect of base material, restorative material and finish line on marginal and internal fit and fracture strength (FS) of endocrowns (N = 64). The restorative materials were ceramic and hybrid ceramic, the preparations were ferrule and modified butt joint (BJ) with two grooves, and the bases were with and without fiber ribbon. Marginal and internal fit were assessed using the triple scan. Statistical analyses were performed using three-way ANOVA. The absolute marginal discrepancy (AMD), marginal discrepancy and overall fit values obtained for ceramic were 127 µm, 108 µm and 120 µm, whereas those obtained for hybrid ceramic were 139 µm, 116 µm and 130 µm, respectively (p < 0.05). The overall FS obtained for ceramic was 662 N, whereas that for hybrid ceramic was 903 N (p < 0.001). When the material was evaluated regardless of preparation and base, ceramic and hybrid ceramic exceeded the selected clinical acceptability threshold for AMD, but did not exceed it for other parameters. Hybrid ceramic restorations with ferrules and fiber bases tended to provide the highest FS, whereas ceramic restorations with modified BJs and without fiber bases tended to provide the lowest FS.