Zhefu Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhefu Yang has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
Jie Hong
7 shared publications- Yanhong Ma
Research Institute of Aero-Engine, Beihang University, Beijing 102206, China
7 shared publications - Jie Hong
School of Energy and Power Engineering, Beihang University, Beijing 100191, China
6 shared publications Zhihong Song
6 shared publicationsYanhong Ma
5 shared publications- Zhihong Song
Research Institute of Aeroengine, Beihang University, Beijing, China
5 shared publications
Latest Publications
- 3 November 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 180
A novel failure mechanism of plastic bending in a low-pressure turbine shaft induced by dual-rotor coupled vibration
- 3 November 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 180
A novel failure mechanism of plastic bending in a low-pressure turbine shaft induced by dual-rotor coupled vibration
- Open Access
- 3 March 2026
- Published by IOS Press
- p. 184-194
Study on the Self-Excited Vibration of Rotor Systems with Bearing Housing Clearance
With the development of advanced aero-engines to higher maneuverability, the inertial loads on the rotor systems would cause larger vibration amplitude and bearing load, which might lead to violent periodic collisions between the bearing housing and limit stop structure. More importantly, the impact load from the collision could change the whirling states of rotor systems, for example resulting in subharmonic, superharmonic, and self-excited vibrations, which might seriously affect the steady and reliable performance of rotor systems. To accurately characterize the influence of bearing housing-limit stop collisions on rotor dynamic response, a new model for the support structure with clearance is proposed considering the energy loss during the collision. A typical rotor-support structure system is studied to investigate the effect of the limit stop on the rotor dynamic response at different rotational speeds. Results show that, in the subcritical speed state, the collision impact does not cause stable self-excited vibration; while in some supercritical states, the rotor may experience self-excited vibration. The frequency of self-excited vibration is approximately equal to the rotor’s low-order forward whirling mode frequency, and will increase with the deepening of the collision indentation. This paper provides a theoretical basis for rotor-support system dynamic response control and vibration troubleshooting.
- 3 March 2026
- Published by IOS Press
- p. 184-194
Open AccessStudy on the Self-Excited Vibration of Rotor Systems with Bearing Housing Clearance
With the development of advanced aero-engines to higher maneuverability, the inertial loads on the rotor systems would cause larger vibration amplitude and bearing load, which might lead to violent periodic collisions between the bearing housing and limit stop structure. More importantly, the impact load from the collision could change the whirling states of rotor systems, for example resulting in subharmonic, superharmonic, and self-excited vibrations, which might seriously affect the steady and reliable performance of rotor systems. To accurately characterize the influence of bearing housing-limit stop collisions on rotor dynamic response, a new model for the support structure with clearance is proposed considering the energy loss during the collision. A typical rotor-support structure system is studied to investigate the effect of the limit stop on the rotor dynamic response at different rotational speeds. Results show that, in the subcritical speed state, the collision impact does not cause stable self-excited vibration; while in some supercritical states, the rotor may experience self-excited vibration. The frequency of self-excited vibration is approximately equal to the rotor’s low-order forward whirling mode frequency, and will increase with the deepening of the collision indentation. This paper provides a theoretical basis for rotor-support system dynamic response control and vibration troubleshooting.
- Open Access
Reliability Evaluation Method for Aeroengine Turbine Rotor Assemblies Considering Interaction of Multiple Failure Modes
In complex mechanical systems involving multiple parts and contact interfaces, failure modes are not only statistically correlated but may also interact through underlying physical mechanisms. These interactions, often neglected in current reliability analysis, can lead to significant deviations in failure predictions, especially in rotor systems and actuators. Taking aeroengine turbine rotor assemblies as an example, multiple failure modes, such as wear, fatigue and slip at contact interfaces, affect key mechanical property parameters including assembly preload, cylindrical interference fit and cooling performance. These variations lead to evolving stress/strain and temperature fields with increasing load cycles, thereby inducing physical interactions among different failure modes. This study systematically analyzes the interaction mechanisms among multiple failure modes within a turbine rotor assembly. A mechanics model is established to quantify these interactions and their effects on failure evolution. Furthermore, a time-dependent reliability evaluation method is proposed based on Monte Carlo simulation and the Probability Network Evaluation Technique. A case study illustrates that both continuous-type and trigger-type interactions significantly affect the failure probabilities of wear and low-cycle fatigue. The results emphasize the necessity of accounting for interaction of multi-failure modes to improve the accuracy of failure prediction and enhance the design reliability of turbine rotor assemblies.
Open AccessReliability Evaluation Method for Aeroengine Turbine Rotor Assemblies Considering Interaction of Multiple Failure Modes
In complex mechanical systems involving multiple parts and contact interfaces, failure modes are not only statistically correlated but may also interact through underlying physical mechanisms. These interactions, often neglected in current reliability analysis, can lead to significant deviations in failure predictions, especially in rotor systems and actuators. Taking aeroengine turbine rotor assemblies as an example, multiple failure modes, such as wear, fatigue and slip at contact interfaces, affect key mechanical property parameters including assembly preload, cylindrical interference fit and cooling performance. These variations lead to evolving stress/strain and temperature fields with increasing load cycles, thereby inducing physical interactions among different failure modes. This study systematically analyzes the interaction mechanisms among multiple failure modes within a turbine rotor assembly. A mechanics model is established to quantify these interactions and their effects on failure evolution. Furthermore, a time-dependent reliability evaluation method is proposed based on Monte Carlo simulation and the Probability Network Evaluation Technique. A case study illustrates that both continuous-type and trigger-type interactions significantly affect the failure probabilities of wear and low-cycle fatigue. The results emphasize the necessity of accounting for interaction of multi-failure modes to improve the accuracy of failure prediction and enhance the design reliability of turbine rotor assemblies.
- Open Access
A Novel Evaluation Method for Vibration Coupling of Complex Rotor–Stator Systems in Aeroengines
With the increase in thrust–weight ratio of advanced aeroengines, the rotor and stator often exhibit comparable stiffness characteristics, leading to significant vibration coupling which harms the safety and reliability of operations. However, an effective vibration coupling evaluation method for complex rotor–stator systems is still lacking. This paper proposes the Vibration Coupling Evaluation Factor (VCEF) to quantitatively evaluate the interaction between the rotor and stator within the framework of the linear system. Then a new evaluation procedure is established for the structural optimization during the early design phase and the fault source localization in troubleshooting scenarios in the high-speed rotating machinery. In this paper, two typical rotor–stator systems are studied with the VCEF method: a simplified rotor–stator system is studied numerically to reveal the influence pattern of different parameters, and a complex rotor–stator system is studied numerically and experimentally to examine the validity of the evaluation method. The results show that VCEF can effectively capture rotor–stator vibration coupling. The VCEF curve with rotational speed shows a significant stepped decrease, indicating a significant strengthening of the rotor–stator vibration coupling, which aligns closely with experimental data. This evaluation method quantitatively assesses the degree of rotor–stator vibration coupling by comparing the differences in modal characteristics between the rotor system and the rotor–stator system under the gyroscopic effect. Optimizing rotor–stator stiffness and mass distribution based on VCEF mitigates operational risks in high-speed regimes. This methodology provides engineers with a systematic, quantitative tool to determine when integrated rotor–stator analysis is essential for accurate dynamic prediction and offers broad applicability to aeroengine design and other high-speed rotating machinery.
Open AccessA Novel Evaluation Method for Vibration Coupling of Complex Rotor–Stator Systems in Aeroengines
With the increase in thrust–weight ratio of advanced aeroengines, the rotor and stator often exhibit comparable stiffness characteristics, leading to significant vibration coupling which harms the safety and reliability of operations. However, an effective vibration coupling evaluation method for complex rotor–stator systems is still lacking. This paper proposes the Vibration Coupling Evaluation Factor (VCEF) to quantitatively evaluate the interaction between the rotor and stator within the framework of the linear system. Then a new evaluation procedure is established for the structural optimization during the early design phase and the fault source localization in troubleshooting scenarios in the high-speed rotating machinery. In this paper, two typical rotor–stator systems are studied with the VCEF method: a simplified rotor–stator system is studied numerically to reveal the influence pattern of different parameters, and a complex rotor–stator system is studied numerically and experimentally to examine the validity of the evaluation method. The results show that VCEF can effectively capture rotor–stator vibration coupling. The VCEF curve with rotational speed shows a significant stepped decrease, indicating a significant strengthening of the rotor–stator vibration coupling, which aligns closely with experimental data. This evaluation method quantitatively assesses the degree of rotor–stator vibration coupling by comparing the differences in modal characteristics between the rotor system and the rotor–stator system under the gyroscopic effect. Optimizing rotor–stator stiffness and mass distribution based on VCEF mitigates operational risks in high-speed regimes. This methodology provides engineers with a systematic, quantitative tool to determine when integrated rotor–stator analysis is essential for accurate dynamic prediction and offers broad applicability to aeroengine design and other high-speed rotating machinery.
- 22 December 2025
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 114 (1) , 58
Dynamic effects of bulge interface fretting wear on elastic ring squeeze film dampers
- 22 December 2025
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 114 (1) , 58
Dynamic effects of bulge interface fretting wear on elastic ring squeeze film dampers
- Open Access
Research on the Dynamic Behavior of Rotor–Stator Systems Considering Bearing Clearance in Aeroengines
The high-performance aeroengine operates under extreme loads. In engineering practice, the vibration problems caused by stator vibrations have become increasingly prominent, with impacts on the rotor dynamic behavior. This paper takes the rotor–stator system of aeroengines as the analysis object and studies the influence of stator modal vibration on the rotor dynamic behavior. The dynamic model of the rotor–stator system has been established, and the influence of the contact state of cylindrical roller bearings (CRBs) has been analyzed by considering bearing clearance. To precisely capture the transient contact state within the CRBs, a numerical method combining the Newmark-β method with the Event Function has been developed. The numerical calculation results show that the collision effect introduced by the bearing clearance will excite a localized stator mode at the supercritical state, which fundamentally alters the rotor dynamic behavior: generating prominent combination frequencies due to modulation between the rotor rotation and the stator vibration . Moreover, good consistency between the experimental and calculated results has been obtained. This study demonstrates that the stator modal vibration can critically modify rotor dynamic behavior in supercritical operation, leading to potentially hazardous non-synchronous whirl. The integrated model and numerical method provide a robust framework for analyzing complex rotor–stator interactions, offering significant insights for vibration control and fault diagnosis in high-speed rotating machinery.Open AccessResearch on the Dynamic Behavior of Rotor–Stator Systems Considering Bearing Clearance in Aeroengines
The high-performance aeroengine operates under extreme loads. In engineering practice, the vibration problems caused by stator vibrations have become increasingly prominent, with impacts on the rotor dynamic behavior. This paper takes the rotor–stator system of aeroengines as the analysis object and studies the influence of stator modal vibration on the rotor dynamic behavior. The dynamic model of the rotor–stator system has been established, and the influence of the contact state of cylindrical roller bearings (CRBs) has been analyzed by considering bearing clearance. To precisely capture the transient contact state within the CRBs, a numerical method combining the Newmark-β method with the Event Function has been developed. The numerical calculation results show that the collision effect introduced by the bearing clearance will excite a localized stator mode at the supercritical state, which fundamentally alters the rotor dynamic behavior: generating prominent combination frequencies due to modulation between the rotor rotation and the stator vibration . Moreover, good consistency between the experimental and calculated results has been obtained. This study demonstrates that the stator modal vibration can critically modify rotor dynamic behavior in supercritical operation, leading to potentially hazardous non-synchronous whirl. The integrated model and numerical method provide a robust framework for analyzing complex rotor–stator interactions, offering significant insights for vibration control and fault diagnosis in high-speed rotating machinery. - 19 October 2025
- Published by Elsevier in Engineering Failure Analysis
- Vol. 183
Mechanism analysis of sequential failure in aeroengine turbine assembly under non-uniform preload
- 19 October 2025
- Published by Elsevier in Engineering Failure Analysis
- Vol. 183
Mechanism analysis of sequential failure in aeroengine turbine assembly under non-uniform preload
- Open Access
Dynamics Study of Multi-Supports Rotor Systems with Bearing Clearance Considering Angular Deflections
Bearing clearance, prevalent in multi-supports rotor systems of aero engines, exerts a significant influence on the dynamics of rotor systems, actuators, and aero engines. The essence of it lies in the complex mechanical effects between the bearing and support. These effects become more complicated when significant relative angular deflections between the bearing and support exist, which is rarely considered in previous studies. In this paper, a model of support structure with bearing clearance considering angular deflections is proposed, and a mechanical model of the multi-supports rotor system with bearing clearance is developed. The dynamic response of the multi-supports rotor system with bearing clearance is investigated by numerical calculation and experimental verification. The results indicate that, in addition to the rotational frequency, remarkable harmonic frequency components occur in the response, which are generated by the relative movement and periodical collision between the bearing and support, and the relative angular deflections between the bearing and support have a significant impact on the amplitude of them; reducing the bearing clearance or increasing the misalignment both leads to a notable increase in the amplitudes of the harmonic frequency components.
Open AccessDynamics Study of Multi-Supports Rotor Systems with Bearing Clearance Considering Angular Deflections
Bearing clearance, prevalent in multi-supports rotor systems of aero engines, exerts a significant influence on the dynamics of rotor systems, actuators, and aero engines. The essence of it lies in the complex mechanical effects between the bearing and support. These effects become more complicated when significant relative angular deflections between the bearing and support exist, which is rarely considered in previous studies. In this paper, a model of support structure with bearing clearance considering angular deflections is proposed, and a mechanical model of the multi-supports rotor system with bearing clearance is developed. The dynamic response of the multi-supports rotor system with bearing clearance is investigated by numerical calculation and experimental verification. The results indicate that, in addition to the rotational frequency, remarkable harmonic frequency components occur in the response, which are generated by the relative movement and periodical collision between the bearing and support, and the relative angular deflections between the bearing and support have a significant impact on the amplitude of them; reducing the bearing clearance or increasing the misalignment both leads to a notable increase in the amplitudes of the harmonic frequency components.