Matthew H. Kmetz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Matthew H. Kmetz has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- David H. Timm
Department of Civil and Environmental Engineering, Auburn University, Auburn, AL
3 shared publications - Carolina Rodezno
National Center for Asphalt Technology, Auburn University, Auburn, AL
2 shared publications - Adam Taylor
National Center for Asphalt Technology, Auburn University, Auburn, AL
1 shared publication - Fan Yin
National Center for Asphalt Technology, Auburn University, Auburn, AL
1 shared publication - Randy West
National Center for Asphalt Technology, Auburn University, Auburn, AL
1 shared publication Samina Samrose
Department of Civil and Environmental Engineering, Auburn University, Auburn, AL
1 shared publication
Latest Publications
- 7 May 2026
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
Forensic Evaluation of a Dry-Process Rubber-Modified Asphalt Pavement
Atypical horizontal cracking and shear distress, paired with extensive bottom-up fatigue cracking, were identified in a dry-process rubber-modified flexible pavement section belonging to the Additive Group experiment at the National Center for Asphalt Technology Test Track. Exposed to the same accelerated trafficking level, the wet-process styrene butadiene styrene- modified control section displayed no such distress. An initial forensic evaluation characterized the distress and proposed mechanism(s) for distress initiation/propagation using analyses of the asphalt mixtures, backcalculated layer moduli, measured pavement responses, structural response simulation via Waterways Experiment Station Layered Elastic Analysis (WESLEA) for Windows 3.0 (WFW), and fatigue cracking damage evolution simulation via FlexPAVE 1.1 (FP). The objective of this paper was to provide support for the theories established in the previous investigation (on the mechanisms responsible for distress). Therefore, shear strength testing of the mixtures was performed, where a significant reduction in shear stress resistance was observed for the rubber-modified material versus the control material. Structural response simulation via FP confirmed the presence of significant internal horizontal shear stress development with the asphalt concrete (AC) layer under dual-tire loadings similar to the conditions found at the Test Track. Therefore, this could have led to the initiation and propagation of horizontal cracking and shear distress, given the rubber-modified mixture’s reduced capacity for shear resistance. The horizontal cracking condition in the rubber-modified section was modeled via WFW. The resulting tensile strain responses showed the best agreement with the field-measured quantities, indicating that horizontal cracking in the rubber-modified AC layer magnified the measured tensile strain responses.
- 7 May 2026
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
Forensic Evaluation of a Dry-Process Rubber-Modified Asphalt Pavement
Atypical horizontal cracking and shear distress, paired with extensive bottom-up fatigue cracking, were identified in a dry-process rubber-modified flexible pavement section belonging to the Additive Group experiment at the National Center for Asphalt Technology Test Track. Exposed to the same accelerated trafficking level, the wet-process styrene butadiene styrene- modified control section displayed no such distress. An initial forensic evaluation characterized the distress and proposed mechanism(s) for distress initiation/propagation using analyses of the asphalt mixtures, backcalculated layer moduli, measured pavement responses, structural response simulation via Waterways Experiment Station Layered Elastic Analysis (WESLEA) for Windows 3.0 (WFW), and fatigue cracking damage evolution simulation via FlexPAVE 1.1 (FP). The objective of this paper was to provide support for the theories established in the previous investigation (on the mechanisms responsible for distress). Therefore, shear strength testing of the mixtures was performed, where a significant reduction in shear stress resistance was observed for the rubber-modified material versus the control material. Structural response simulation via FP confirmed the presence of significant internal horizontal shear stress development with the asphalt concrete (AC) layer under dual-tire loadings similar to the conditions found at the Test Track. Therefore, this could have led to the initiation and propagation of horizontal cracking and shear distress, given the rubber-modified mixture’s reduced capacity for shear resistance. The horizontal cracking condition in the rubber-modified section was modeled via WFW. The resulting tensile strain responses showed the best agreement with the field-measured quantities, indicating that horizontal cracking in the rubber-modified AC layer magnified the measured tensile strain responses.
- 4 October 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2680 (1) , 613-628
Initial Forensic Evaluation of a Dry-Process Rubber-Modified Asphalt Pavement
The Additive Group (AG) experiment at the National Center for Asphalt Technology (NCAT) Test Track includes a section paved with a dry-process rubber-modified asphalt mixture (GTRDry) which has displayed severe levels of cracking after 10 million equivalent single-axle loads (ESAL) of accelerated trafficking. In the same period, the styrene–butadiene–styrene (SBS) modified control mixture displayed no cracking. Both mixtures displayed similar laboratory evaluated dynamic modulus |E*| and fatigue properties. The objective of this investigation was to determine the cause of the unexpected cracking observed in the GTRDry test section via forensic analysis, laboratory data, measured structural responses, and structural simulation. It was found that GTRDry had significantly lower foundation support relative to the control, and its average temperature-corrected asphalt concrete (AC) modulus (E 68 ) was lower than expected (based on the results of |E*| testing). Both factors contributed to the high tensile strains at the bottom of the AC layer (double those of the control). This was assumed to be the sole cause of the GTRDry cracking (a traditional bottom-up fatigue cracking mechanism), until forensic coring revealed mid-depth, horizontal cracking, prompting structural simulations via WESLEA. The results indicated that the lower AC and support moduli of the GTRDry section resulted in higher flexural strain responses. Peak shear stresses occurred near the location of mid-depth cracking; however, the magnitudes were found to be independent of the layer moduli, remaining relatively similar between the two sections. It was, therefore, concluded that the paved N1 (GTRDry) mixture was potentially more susceptible to horizontal cracking and bottom-up fatigue cracking distresses than the SBS-modified control.
- 4 October 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2680 (1) , 613-628
Initial Forensic Evaluation of a Dry-Process Rubber-Modified Asphalt Pavement
The Additive Group (AG) experiment at the National Center for Asphalt Technology (NCAT) Test Track includes a section paved with a dry-process rubber-modified asphalt mixture (GTRDry) which has displayed severe levels of cracking after 10 million equivalent single-axle loads (ESAL) of accelerated trafficking. In the same period, the styrene–butadiene–styrene (SBS) modified control mixture displayed no cracking. Both mixtures displayed similar laboratory evaluated dynamic modulus |E*| and fatigue properties. The objective of this investigation was to determine the cause of the unexpected cracking observed in the GTRDry test section via forensic analysis, laboratory data, measured structural responses, and structural simulation. It was found that GTRDry had significantly lower foundation support relative to the control, and its average temperature-corrected asphalt concrete (AC) modulus (E 68 ) was lower than expected (based on the results of |E*| testing). Both factors contributed to the high tensile strains at the bottom of the AC layer (double those of the control). This was assumed to be the sole cause of the GTRDry cracking (a traditional bottom-up fatigue cracking mechanism), until forensic coring revealed mid-depth, horizontal cracking, prompting structural simulations via WESLEA. The results indicated that the lower AC and support moduli of the GTRDry section resulted in higher flexural strain responses. Peak shear stresses occurred near the location of mid-depth cracking; however, the magnitudes were found to be independent of the layer moduli, remaining relatively similar between the two sections. It was, therefore, concluded that the paved N1 (GTRDry) mixture was potentially more susceptible to horizontal cracking and bottom-up fatigue cracking distresses than the SBS-modified control.
- 24 April 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2679 (6) , 489-501
Laboratory and Field Performance Characterization of Recycled-Plastic-Modified Asphalt Mixtures at the National Center for Asphalt Technology Test Track
This study evaluated the performance of two recycled-plastic-modified (RPM) asphalt mixtures versus a nonplastic control mixture through laboratory performance testing, FlexPAVE™ simulations, and accelerated pavement testing at the National Center for Asphalt Technology (NCAT) Test Track. One RPM mixture used the wet process of adding linear low-density polyethylene (LLDPE) for asphalt binder modification, and the other the dry process of adding LLDPE for mixture modification using a drop-in approach. The nonplastic control mixture used a binder modified by styrene-butadiene-styrene. Each mixture was produced in an asphalt plant and placed as a single-lift asphalt layer of a structural test section at the NCAT Test Track. Laboratory performance testing showed that the wet plastic mixture had comparable properties to the control, while the dry plastic mixture had significantly higher stiffness, better rutting resistance, but worse cracking resistance than the control mixture. Using a representative pavement structure and layer properties as inputs, FlexPAVE™ simulations predicted that the dry plastic section would have the best fatigue-cracking performance, followed by the control and wet plastic sections, respectively. In situ pavement structural characterization data showed the control section had lower asphalt layer moduli, higher granular base and subgrade moduli, and lower measured strain at the bottom of the asphalt layer than the two plastic sections. Through 10 million equivalent single axle loads of trafficking, all three test sections showed steady smoothness and comparable rutting and friction performance. The dry plastic section had 3.5% surface cracking, while the control and wet plastic sections remained intact with no cracking.
- 24 April 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2679 (6) , 489-501
Laboratory and Field Performance Characterization of Recycled-Plastic-Modified Asphalt Mixtures at the National Center for Asphalt Technology Test Track
This study evaluated the performance of two recycled-plastic-modified (RPM) asphalt mixtures versus a nonplastic control mixture through laboratory performance testing, FlexPAVE™ simulations, and accelerated pavement testing at the National Center for Asphalt Technology (NCAT) Test Track. One RPM mixture used the wet process of adding linear low-density polyethylene (LLDPE) for asphalt binder modification, and the other the dry process of adding LLDPE for mixture modification using a drop-in approach. The nonplastic control mixture used a binder modified by styrene-butadiene-styrene. Each mixture was produced in an asphalt plant and placed as a single-lift asphalt layer of a structural test section at the NCAT Test Track. Laboratory performance testing showed that the wet plastic mixture had comparable properties to the control, while the dry plastic mixture had significantly higher stiffness, better rutting resistance, but worse cracking resistance than the control mixture. Using a representative pavement structure and layer properties as inputs, FlexPAVE™ simulations predicted that the dry plastic section would have the best fatigue-cracking performance, followed by the control and wet plastic sections, respectively. In situ pavement structural characterization data showed the control section had lower asphalt layer moduli, higher granular base and subgrade moduli, and lower measured strain at the bottom of the asphalt layer than the two plastic sections. Through 10 million equivalent single axle loads of trafficking, all three test sections showed steady smoothness and comparable rutting and friction performance. The dry plastic section had 3.5% surface cracking, while the control and wet plastic sections remained intact with no cracking.