Shulin Lü
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shulin Lü has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
Shusen Wu
11 shared publicationsWenbo Guo
10 shared publicationsZhaoxiang Yan
10 shared publicationsKewang Xiang
7 shared publications- Shusen Wu
State Key Lab of Materials Processing and Die & Mould Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan, China
7 shared publications Zhimin Wu
7 shared publications
Latest Publications
- 8 August 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1080
Microstructure, mechanical properties and crack propagation mechanism of (SiCₚ+Tiₚ)/AZ61 composites
- 8 August 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1080
Microstructure, mechanical properties and crack propagation mechanism of (SiCₚ+Tiₚ)/AZ61 composites
- Open Access
- 24 June 2026
- Published by Elsevier in SSRN Electronic Journal
Microstructure, mechanical properties and crack propagation mechanism of (SiCₚ+Tiₚ)/AZ61 composites
In this work, (SiCₚ+Tiₚ)/AZ61 composites were prepared via aeration-ultrasonic assisted semi-solid stirring combined with a novel continuous squeeze casting-extrusion (CSCE) process. The results show that Mn₂Ti, the interfacial reaction product formed on the surface of Ti particles, acts as a strong bonding medium, resulting in a robust Ti/Mg interface with synergistically optimized chemical affinity and mechanical interlocking. Meanwhile, first-principles calculations indicate that the enrichment of Al, Mn and Si elements at the Ti particle interface is beneficial to increasing the interfacial adhesion work, promoting interfacial charge interactions, and thus enhancing the Ti/Mg interfacial bonding strength. Compared with the AZ61 matrix alloy, the ultimate tensile strength (UTS), yield strength (YS) and elastic modulus of the (SiCₚ+Tiₚ)/AZ61 composites are improved by approximately 26%, 39% and 38%, reaching 392.6 MPa, 272.2 MPa and 64.5GPa, respectively, while the elongation is still maintained at 13.3%. In addition, microcracks initiated at the sharp corners of SiC particles are passivated by Ti particles, and their propagation paths in the matrix are greatly prolonged, thereby alleviating the ductility loss caused by high-content micron-sized particles.
- 24 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMicrostructure, mechanical properties and crack propagation mechanism of (SiCₚ+Tiₚ)/AZ61 composites
In this work, (SiCₚ+Tiₚ)/AZ61 composites were prepared via aeration-ultrasonic assisted semi-solid stirring combined with a novel continuous squeeze casting-extrusion (CSCE) process. The results show that Mn₂Ti, the interfacial reaction product formed on the surface of Ti particles, acts as a strong bonding medium, resulting in a robust Ti/Mg interface with synergistically optimized chemical affinity and mechanical interlocking. Meanwhile, first-principles calculations indicate that the enrichment of Al, Mn and Si elements at the Ti particle interface is beneficial to increasing the interfacial adhesion work, promoting interfacial charge interactions, and thus enhancing the Ti/Mg interfacial bonding strength. Compared with the AZ61 matrix alloy, the ultimate tensile strength (UTS), yield strength (YS) and elastic modulus of the (SiCₚ+Tiₚ)/AZ61 composites are improved by approximately 26%, 39% and 38%, reaching 392.6 MPa, 272.2 MPa and 64.5GPa, respectively, while the elongation is still maintained at 13.3%. In addition, microcracks initiated at the sharp corners of SiC particles are passivated by Ti particles, and their propagation paths in the matrix are greatly prolonged, thereby alleviating the ductility loss caused by high-content micron-sized particles.
- 29 March 2026
- Published by Springer Nature in Journal of Materials Science
- Vol. 61 (19) , 13631-13649
Effects of alloying elements on Ti/Mg interfacial properties: first-principles combined with experiments
- 29 March 2026
- Published by Springer Nature in Journal of Materials Science
- Vol. 61 (19) , 13631-13649
Effects of alloying elements on Ti/Mg interfacial properties: first-principles combined with experiments
- Open Access
- 26 February 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 41, 7211-7224
A novel bottom-up fabrication strategy of heterostructured extruded magnesium alloys based on multiple heterogeneities in as-cast billets
- 26 February 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 41, 7211-7224
Open AccessA novel bottom-up fabrication strategy of heterostructured extruded magnesium alloys based on multiple heterogeneities in as-cast billets
- Open Access
- 11 February 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of TiB2 content on microstructure and mechanical properties of TiB2/6082 composites fabricated by continuous squeeze casting-extrusion process
In this paper, in-situ TiB2/6082 aluminum matrix composites with different TiB2 contents (0, 3, 6, 9 wt.%) were prepared via a novel continuous squeeze casting-extrusion (CSCE) process, and the evolution of their microstructure and mechanical properties was systematically investigated. Results demonstrate that the CSCE process can effectively eliminate casting defects, disperse TiB2 particle agglomeration, and promote dynamic recrystallization, thereby achieving composites with significantly refined microstructures and uniformly distributed TiB2 particles. TiB2 particles play a crucial role in microstructure regulation: during solidification, they act as heterogeneous nucleation sites for the Mg2Si phase,refining their morphology from a continuous network into fine particles; during hot extrusion, they facilitate dynamic recrystallization and weaken matrix texture through the particle stimulated nucleation (PSN) mechanism. For the as-extruded composites, both yield strength (YS) and ultimate tensile strength (UTS) improve with increasing TiB2 content, reaching optimal values of 154.6 MPa and 232.6 MPa at a TiB2 content of 9 wt.%. The enhancement of the composites’ strength is mainly attributed to the dislocation strengthening mechanism. After T6 heat treatment, nano-scale GP zones and βʹʹ phases precipitate in the composites. The T6-treated 9 wt.% TiB2/6082 composite exhibits the highest YS of 358.9 MPa and UTS of 389.4 MPa. However, high TiB2 content induced particle agglomeration, resulting in reduced elongation and a transition in the fracture mechanism from ductile to a mixed ductile-brittle mode.
- 11 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of TiB2 content on microstructure and mechanical properties of TiB2/6082 composites fabricated by continuous squeeze casting-extrusion process
In this paper, in-situ TiB2/6082 aluminum matrix composites with different TiB2 contents (0, 3, 6, 9 wt.%) were prepared via a novel continuous squeeze casting-extrusion (CSCE) process, and the evolution of their microstructure and mechanical properties was systematically investigated. Results demonstrate that the CSCE process can effectively eliminate casting defects, disperse TiB2 particle agglomeration, and promote dynamic recrystallization, thereby achieving composites with significantly refined microstructures and uniformly distributed TiB2 particles. TiB2 particles play a crucial role in microstructure regulation: during solidification, they act as heterogeneous nucleation sites for the Mg2Si phase,refining their morphology from a continuous network into fine particles; during hot extrusion, they facilitate dynamic recrystallization and weaken matrix texture through the particle stimulated nucleation (PSN) mechanism. For the as-extruded composites, both yield strength (YS) and ultimate tensile strength (UTS) improve with increasing TiB2 content, reaching optimal values of 154.6 MPa and 232.6 MPa at a TiB2 content of 9 wt.%. The enhancement of the composites’ strength is mainly attributed to the dislocation strengthening mechanism. After T6 heat treatment, nano-scale GP zones and βʹʹ phases precipitate in the composites. The T6-treated 9 wt.% TiB2/6082 composite exhibits the highest YS of 358.9 MPa and UTS of 389.4 MPa. However, high TiB2 content induced particle agglomeration, resulting in reduced elongation and a transition in the fracture mechanism from ductile to a mixed ductile-brittle mode.
- 2 May 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 936
An efficient aeration-ultrasonic process for preparing SiCp/AZ61 composites
- 2 May 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 936
An efficient aeration-ultrasonic process for preparing SiCp/AZ61 composites