Amina Ghedjemis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Amina Ghedjemis has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Cherif Belebchouche
Civil Engineering Research Laboratory of Sétif (LRGCS), Department of Civil Engineering, Setif 1 University-Ferhat Abbas, Sétif 19000, Algeria
2 shared publications - El Hadj Kadri
Mechanics and Civil Engineering Materials Laboratory (L2MGC), University of CY-Paris, Cergy-Pontoise, 95031 Neuville-sur-Oise, France
2 shared publications - Kamel Hebbache
Civil Engineering Research Laboratory of Sétif (LRGCS), Department of Civil Engineering, Setif 1 University-Ferhat Abbas, Sétif 19000, Algeria
2 shared publications - Maya Kebaili
Mechanics Research Center (CRM), Constantine 25021, Algeria
2 shared publications - Ali Yacine Sahnoun
Studies in Engineering and Exact Sciences v.5 n.2 p.01 -18 2024 Curitiba
1 shared publication - Ilyes Abacha
Mechanics Research Center (CRM), Constantine 25021, Algeria
1 shared publication
Latest Publications
- Open Access
Elaboration of Natural Hydroxyapatite Coating by Plasma Spraying
Metallic implants used in orthopedics, such as titanium alloys, possess excellent mechanical strength but suffer from corrosion and poor bio-integration, often necessitating revision surgeries. Bioactive coatings, particularly hydroxyapatite, can enhance implant osteoconductivity, but high-purity synthetic hydroxyapatite is costly. This study investigates the development and characterization of a low-cost, biocompatible coating using hydroxyapatite derived from an unconventional natural source dromedary bone applied onto a titanium substrate via plasma spraying. Hydroxyapatite powder was synthesized from dromedary femurs through a thermal treatment process at 1000 °C. The resulting powder was then deposited onto a sandblasted titanium dioxide substrate using an atmospheric plasma spray technique. The physicochemical, structural, and morphological properties of both the source powder and the final coating were comprehensively analyzed using Scanning Electron Microscopy, Energy Dispersive X-ray Spectroscopy, X-ray Diffraction, and Fourier-Transform Infrared Spectroscopy. Characterization of the powder confirmed the successful synthesis of pure, crystalline hydroxyapatite, with Fourier-Transform Infrared Spectroscopy analysis verifying the complete removal of organic matter. The plasma-sprayed coating exhibited good adhesion and a homogenous, lamellar microstructure typical of thermal spray processes, with an average thickness of approximately 95 μm. X-ray Diffraction analysis of the coating revealed that while hydroxyapatite remained the primary phase, partial decomposition occurred during spraying, leading to the formation of secondary phases, including tricalcium phosphate and calcium oxide. Scanning Electron Microscopy imaging showed a porous surface composed of fully and partially melted particles, a feature potentially beneficial for bone integration. The findings demonstrate that dromedary bone is a viable and low-cost precursor for producing bioactive hydroxyapatite coatings for orthopedic implants. The plasma spray method successfully creates a well-adhered, porous coating, though process-induced phase changes must be considered for biomedical applications.
Open AccessElaboration of Natural Hydroxyapatite Coating by Plasma Spraying
Metallic implants used in orthopedics, such as titanium alloys, possess excellent mechanical strength but suffer from corrosion and poor bio-integration, often necessitating revision surgeries. Bioactive coatings, particularly hydroxyapatite, can enhance implant osteoconductivity, but high-purity synthetic hydroxyapatite is costly. This study investigates the development and characterization of a low-cost, biocompatible coating using hydroxyapatite derived from an unconventional natural source dromedary bone applied onto a titanium substrate via plasma spraying. Hydroxyapatite powder was synthesized from dromedary femurs through a thermal treatment process at 1000 °C. The resulting powder was then deposited onto a sandblasted titanium dioxide substrate using an atmospheric plasma spray technique. The physicochemical, structural, and morphological properties of both the source powder and the final coating were comprehensively analyzed using Scanning Electron Microscopy, Energy Dispersive X-ray Spectroscopy, X-ray Diffraction, and Fourier-Transform Infrared Spectroscopy. Characterization of the powder confirmed the successful synthesis of pure, crystalline hydroxyapatite, with Fourier-Transform Infrared Spectroscopy analysis verifying the complete removal of organic matter. The plasma-sprayed coating exhibited good adhesion and a homogenous, lamellar microstructure typical of thermal spray processes, with an average thickness of approximately 95 μm. X-ray Diffraction analysis of the coating revealed that while hydroxyapatite remained the primary phase, partial decomposition occurred during spraying, leading to the formation of secondary phases, including tricalcium phosphate and calcium oxide. Scanning Electron Microscopy imaging showed a porous surface composed of fully and partially melted particles, a feature potentially beneficial for bone integration. The findings demonstrate that dromedary bone is a viable and low-cost precursor for producing bioactive hydroxyapatite coatings for orthopedic implants. The plasma spray method successfully creates a well-adhered, porous coating, though process-induced phase changes must be considered for biomedical applications.
- Open Access
Utilizing Residual Industrial Waste as Sustainable Adsorbents for the Removal of Indigo Carmine from Contaminated Water
The recovery of green waste and biomass presents a significant challenge in the 21st century. In this context, this study aims to valorize waste generated by the fruit juice processing industry at the N’Gaous unit (composed of the orange peel, fibers, pulp, and seeds) as an adsorbent to eliminate an anionic dye and to enhance its adsorption capacity through thermal activation at 200 °C and 400 °C. The aim is also to determine the parameters for the adsorption process including contact time (0–120 min), solution pH (2–10), initial dye concentration (50–700 mg/L), and adsorbent dosage (0.5–10 g/L). The adsorption tests showed that waste activated at 400 °C (AR400) demonstrated a higher efficiency for removing indigo carmine (IC) from an aqueous solution than waste activated at 200 °C (AR200) and unactivated waste (R). The experimental maximum adsorption capacities for IC were 70 mg/g for unactivated waste, 500 mg/g for waste activated at 200 °C, and 680 mg/g for waste activated at 400 °C. These tests were conducted under conditions of pH 2, an equilibrium time of 50 min, and an adsorbent concentration of 1 g/L. The analysis of the kinetic data revealed that the pseudo-second-order model provides the best fit for the experimental results, indicating that this mechanism predominates in the sorption of the pollutant onto the three adsorbents. In terms of adsorption isotherms, the Freundlich model was found to be the most appropriate for describing the adsorption of dye molecules on the R, AR200, and AR400 supports, owing to its high correlation coefficient. Before adsorption tests, the powder R, AR200 and AR400 were characterized by various analyses, including Fourier transform infrared (FTIR), pH zero charge points and laser granularity for structural evaluation. According to the results of these analyses, the specific surface area (SSA) of the prepared material increases with the increase in the activation temperature, which expresses the increase in the adsorption of material activated at 400 °C, compared with materials activated at 200 °C and the raw material.
Open AccessUtilizing Residual Industrial Waste as Sustainable Adsorbents for the Removal of Indigo Carmine from Contaminated Water
The recovery of green waste and biomass presents a significant challenge in the 21st century. In this context, this study aims to valorize waste generated by the fruit juice processing industry at the N’Gaous unit (composed of the orange peel, fibers, pulp, and seeds) as an adsorbent to eliminate an anionic dye and to enhance its adsorption capacity through thermal activation at 200 °C and 400 °C. The aim is also to determine the parameters for the adsorption process including contact time (0–120 min), solution pH (2–10), initial dye concentration (50–700 mg/L), and adsorbent dosage (0.5–10 g/L). The adsorption tests showed that waste activated at 400 °C (AR400) demonstrated a higher efficiency for removing indigo carmine (IC) from an aqueous solution than waste activated at 200 °C (AR200) and unactivated waste (R). The experimental maximum adsorption capacities for IC were 70 mg/g for unactivated waste, 500 mg/g for waste activated at 200 °C, and 680 mg/g for waste activated at 400 °C. These tests were conducted under conditions of pH 2, an equilibrium time of 50 min, and an adsorbent concentration of 1 g/L. The analysis of the kinetic data revealed that the pseudo-second-order model provides the best fit for the experimental results, indicating that this mechanism predominates in the sorption of the pollutant onto the three adsorbents. In terms of adsorption isotherms, the Freundlich model was found to be the most appropriate for describing the adsorption of dye molecules on the R, AR200, and AR400 supports, owing to its high correlation coefficient. Before adsorption tests, the powder R, AR200 and AR400 were characterized by various analyses, including Fourier transform infrared (FTIR), pH zero charge points and laser granularity for structural evaluation. According to the results of these analyses, the specific surface area (SSA) of the prepared material increases with the increase in the activation temperature, which expresses the increase in the adsorption of material activated at 400 °C, compared with materials activated at 200 °C and the raw material.
- Open Access
- 1 July 2024
- Published by Brazilian Journals in STUDIES IN ENGINEERING AND EXACT SCIENCES
- Vol. 5 (2) , e9271
Optimizing groundwater decarbonation in Bordj Bou Arreridj Highlands (Algeria): comparative study of carbide lime waste from linde gas and caustic soda
Various techniques are employed to mitigate scaling in water supply systems, with chemical treatments being particularly effective in reducing water hardness. Among these, decarbonation using lime is widely adopted due to its ability to precipitate calcium and reduce the potential for scale formation. This study presents a comparative analysis of decarbonation treatments for groundwater in the Bordj Bou Arreridj highlands (Algeria), focusing on the effectiveness of commercial caustic soda and carbide lime waste (CLW), a by-product from acetylene production at Lind Gas in Annaba (Algeria). The primary objective is to reduce water hardness to levels compliant with WHO standards, ensuring the prevention of scaling in domestic and industrial installations. Two distinct groundwater sources, El-Anasser and Bordj Ghedir, characterized by high hardness, were treated using both chemical agents. The study evaluated key parameters, including total alkalinity, calcium hardness, total hardness, and conductivity. The results reveal consistent correlations between the minimum values of these parameters across both treatments, with similar efficacy observed in the reduction of hardness. Notably, the use of CLW offers a sustainable alternative to commercial chemicals, contributing to the valorization of industrial by-products while achieving comparable decarbonation performance. This research underscores the potential for using industrial waste in water treatment applications, promoting both environmental and economic benefits.
- 1 July 2024
- Published by Brazilian Journals in STUDIES IN ENGINEERING AND EXACT SCIENCES
- Vol. 5 (2) , e9271
Open AccessOptimizing groundwater decarbonation in Bordj Bou Arreridj Highlands (Algeria): comparative study of carbide lime waste from linde gas and caustic soda
Various techniques are employed to mitigate scaling in water supply systems, with chemical treatments being particularly effective in reducing water hardness. Among these, decarbonation using lime is widely adopted due to its ability to precipitate calcium and reduce the potential for scale formation. This study presents a comparative analysis of decarbonation treatments for groundwater in the Bordj Bou Arreridj highlands (Algeria), focusing on the effectiveness of commercial caustic soda and carbide lime waste (CLW), a by-product from acetylene production at Lind Gas in Annaba (Algeria). The primary objective is to reduce water hardness to levels compliant with WHO standards, ensuring the prevention of scaling in domestic and industrial installations. Two distinct groundwater sources, El-Anasser and Bordj Ghedir, characterized by high hardness, were treated using both chemical agents. The study evaluated key parameters, including total alkalinity, calcium hardness, total hardness, and conductivity. The results reveal consistent correlations between the minimum values of these parameters across both treatments, with similar efficacy observed in the reduction of hardness. Notably, the use of CLW offers a sustainable alternative to commercial chemicals, contributing to the valorization of industrial by-products while achieving comparable decarbonation performance. This research underscores the potential for using industrial waste in water treatment applications, promoting both environmental and economic benefits.