Bingjun Xiong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bingjun Xiong has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Jingjing Liu
School of Electronics and Communication Engineering, Sun Yat-sen University, Shenzhen, China
7 shared publications - Feng Yan
School of Electronics and Communication Engineering, Sun Yat-sen University, Shenzhen, China
5 shared publications - Yang Wang
College of Integrated Circuit Science and Engineering, Nanjing University of Posts and Telecommunications, Nanjing, China
5 shared publications Zhipeng Li
School of Electronics and Communication Engineering, Sun Yat-sen University, Shenzhen, China
4 shared publications- Jian Guan
School of Electronics and Communication Engineering, Sun Yat-sen University, Shenzhen, China
3 shared publications - Kangkang Sun
School of Electronics and Communication Engineering, Sun Yat-sen University, Shenzhen, China
3 shared publications
Latest Publications
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (7) , 4475-4478
Novel Alternating Dual Direction SCR for On-Chip ESD Protection of 58 V CAN Bus in Automotive Electronics
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (7) , 4475-4478
Novel Alternating Dual Direction SCR for On-Chip ESD Protection of 58 V CAN Bus in Automotive Electronics
- 18 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Consumer Electronics
- Vol. PP (00983063) , 1
Design of a Low-noise Instrumentation Amplifier with Triple-MOS Pseudo-resistor for Bio-signal Acquisition in Consumer Electronics
Low input-referred noise (IRN) and low-power instrumentation amplifier (IA) with small size are crucial for consumer bio-electronic applications. This paper presents a compact, noise-efficient capacitive-coupled IA designed for bio-signal acquisition. The proposed Triple-MOSFET pseudo-resistor (PR) provides ultra-high resistance, a wide operating voltage range, and high linearity. The IA, enhanced by chopper-stabilized technology, effectively reduces noise while minimizing current consumption. An area-efficient DC servo loop with Triple-MOS devices is employed to suppress electrode DC offset. Addi-tionally, parasitic effects are minimized based on layout design, maximizing the advantages of the positive feedback loop. The proposed IA is fabricated using a standard 180 nm CMOS process with an area of 0.49 mm², and operates at a supply of 0.8 V with a current consumption of 1.29 μA. The IRN of this IA is 0.97 μVrms within the 0.5–200 Hz and 2.31 μVrms within the 0.2–5 kHz, achieving competitive noise efficiency factor (1.4) and power efficiency factor (1.56). Furthermore, for a 2 mVpp sine wave input, total harmonic distortion is below -60.2 dB. The precise value of the positive feedback capacitor ensures that the input impedance reaches 628 MΩ at 50 Hz. A prototype test system based on the IA successfully acquired high-quality ECG and EEG signals from subjects. This efficient, low-noise, low-power acquisition chip has broad applications in portable cardiac monitors, brain-machine interfaces, and other biosensors, playing a significant role in enhancing the performance and reliability of these electronic devices.
- 18 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Consumer Electronics
- Vol. PP (00983063) , 1
Design of a Low-noise Instrumentation Amplifier with Triple-MOS Pseudo-resistor for Bio-signal Acquisition in Consumer Electronics
Low input-referred noise (IRN) and low-power instrumentation amplifier (IA) with small size are crucial for consumer bio-electronic applications. This paper presents a compact, noise-efficient capacitive-coupled IA designed for bio-signal acquisition. The proposed Triple-MOSFET pseudo-resistor (PR) provides ultra-high resistance, a wide operating voltage range, and high linearity. The IA, enhanced by chopper-stabilized technology, effectively reduces noise while minimizing current consumption. An area-efficient DC servo loop with Triple-MOS devices is employed to suppress electrode DC offset. Addi-tionally, parasitic effects are minimized based on layout design, maximizing the advantages of the positive feedback loop. The proposed IA is fabricated using a standard 180 nm CMOS process with an area of 0.49 mm², and operates at a supply of 0.8 V with a current consumption of 1.29 μA. The IRN of this IA is 0.97 μVrms within the 0.5–200 Hz and 2.31 μVrms within the 0.2–5 kHz, achieving competitive noise efficiency factor (1.4) and power efficiency factor (1.56). Furthermore, for a 2 mVpp sine wave input, total harmonic distortion is below -60.2 dB. The precise value of the positive feedback capacitor ensures that the input impedance reaches 628 MΩ at 50 Hz. A prototype test system based on the IA successfully acquired high-quality ECG and EEG signals from subjects. This efficient, low-noise, low-power acquisition chip has broad applications in portable cardiac monitors, brain-machine interfaces, and other biosensors, playing a significant role in enhancing the performance and reliability of these electronic devices.
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (9) , 1
An Asynchronous Energy-Harvesting Pixel for CMOS Image Sensors
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (9) , 1
An Asynchronous Energy-Harvesting Pixel for CMOS Image Sensors
- 2 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (1) , 77-82
A Total-Ionizing-Dose Tolerant Dual-Direction SCR With Shallow Snapback for High-Voltage ESD Protection in Radiation Environments
Based on a 0.18- $\boldsymbol {\mu }$ m bipolar-CMOS–DMOS (BCD) process, this work presents a total-ionizing-dose (TID) tolerant electrostatic discharge (ESD) protection device with shallow snapback for high-voltage radiation environments, namely, the parallel NPN-enhanced dual-direction silicon-controlled rectifier (NPNE-SCR). This device significantly improves the holding voltage ( ${V}_{h}\text {)}$ compared to traditional SCR (T-SCR) and parallel NPN SCR (NPN-SCR). The snapback is only 2.8 V (39.0 V). In $\boldsymbol {\gamma }$ -ray irradiation experiments, when the TID reaches 300 krad (Si), the NPNE-SCR maintains the lowest leakage current without significant degradation in ESD performance. Compared with other high-voltage ESD structures, the results show that the NPNE-SCR exhibits excellent characteristics, including a high ${V}_{h}$ , high TID tolerance, and low leakage current, and can serve as a reference solution for high-voltage on-chip ESD protection in space applications.
- 2 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (1) , 77-82
A Total-Ionizing-Dose Tolerant Dual-Direction SCR With Shallow Snapback for High-Voltage ESD Protection in Radiation Environments
Based on a 0.18- $\boldsymbol {\mu }$ m bipolar-CMOS–DMOS (BCD) process, this work presents a total-ionizing-dose (TID) tolerant electrostatic discharge (ESD) protection device with shallow snapback for high-voltage radiation environments, namely, the parallel NPN-enhanced dual-direction silicon-controlled rectifier (NPNE-SCR). This device significantly improves the holding voltage ( ${V}_{h}\text {)}$ compared to traditional SCR (T-SCR) and parallel NPN SCR (NPN-SCR). The snapback is only 2.8 V (39.0 V). In $\boldsymbol {\gamma }$ -ray irradiation experiments, when the TID reaches 300 krad (Si), the NPNE-SCR maintains the lowest leakage current without significant degradation in ESD performance. Compared with other high-voltage ESD structures, the results show that the NPNE-SCR exhibits excellent characteristics, including a high ${V}_{h}$ , high TID tolerance, and low leakage current, and can serve as a reference solution for high-voltage on-chip ESD protection in space applications.
- 23 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (11) , 5838-5843
A Dual-Direction SCR Featuring Shallow Snapback and High-Temperature Robustness for ESD Protection of Industrial Communication Buses
The reliability standards for on-chip electrostatic discharge (ESD) protection in high-voltage industrial communication buses are stringent, and traditional ESD solutions cannot effectively meet the requirements for high holding voltage ( ${V} _{h}$ ) and high-temperature tolerance in these applications. Therefore, this article presents a dual-direction silicon-controlled rectifier (DDSCR) featuring shallow snapback and high-temperature robustness. At the same size, ${V} _{h}$ (38.4 V) of the parallel NPN-enhanced SCR (NPNE_DDSCR), which employs a metal short and no shallow trench isolation (STI), is significantly higher than that of the traditional structure (T_DDSCR) and the parallel NPN structure (NPN_DDSCR). Under high-temperature conditions ranging from $50~^{\circ }$ C to $125~^{\circ }$ C, the structure maintains nanoampere-level leakage current, and the device’s ESD characteristics show no significant degradation. The electrostatic properties of three types of structures were verified based on the 0.18- $\mu $ m bipolar-CMOS–DMOS (BCD) process, and their operating mechanisms were further analyzed using technology computer-aided design (TCAD) simulations. The results show that the NPNE_DDSCR exhibits superior performance, with a human body model (HBM) level exceeding 8 kV, and is suitable for efficient on-chip ESD protection of industrial communication buses.
- 23 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (11) , 5838-5843
A Dual-Direction SCR Featuring Shallow Snapback and High-Temperature Robustness for ESD Protection of Industrial Communication Buses
The reliability standards for on-chip electrostatic discharge (ESD) protection in high-voltage industrial communication buses are stringent, and traditional ESD solutions cannot effectively meet the requirements for high holding voltage ( ${V} _{h}$ ) and high-temperature tolerance in these applications. Therefore, this article presents a dual-direction silicon-controlled rectifier (DDSCR) featuring shallow snapback and high-temperature robustness. At the same size, ${V} _{h}$ (38.4 V) of the parallel NPN-enhanced SCR (NPNE_DDSCR), which employs a metal short and no shallow trench isolation (STI), is significantly higher than that of the traditional structure (T_DDSCR) and the parallel NPN structure (NPN_DDSCR). Under high-temperature conditions ranging from $50~^{\circ }$ C to $125~^{\circ }$ C, the structure maintains nanoampere-level leakage current, and the device’s ESD characteristics show no significant degradation. The electrostatic properties of three types of structures were verified based on the 0.18- $\mu $ m bipolar-CMOS–DMOS (BCD) process, and their operating mechanisms were further analyzed using technology computer-aided design (TCAD) simulations. The results show that the NPNE_DDSCR exhibits superior performance, with a human body model (HBM) level exceeding 8 kV, and is suitable for efficient on-chip ESD protection of industrial communication buses.
- 16 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (14) , 26806-26813
A 0.88-nW Ultralow Gm Tunable Transconductor Based on Bootstrap Body Input for Biomedical Sensors
Low-transconductance (Gm) amplifiers are essential for implementing low-frequency continuous-time filters, a critical aspect for biomedical sensors. This paper proposes a low-power, low-Gm amplifier based on the bootstrap-body-input technique. The input topology of the transconductor consists of two transistors with body-inputs and a source degeneration resistor. The source of the two transistors connected to the resistor, which bootstraps the terminal voltages and expands the input range. To further reduce the Gm value of the transconductor, an area-efficient series-parallel current mirror is adopted. The transconductor was fabricated in a 0.18 μm CMOS process. Measurement results show that the bootstrap-body-input transconductor achieves a reduction in Gm value of more than 1200 times over conventional body-input transconductor. The proposed transconductor features a tuning range of 27 to 581 pA/V at 0.8 V supply voltage, with a power consumption of only 0.88 nW. The input-referred noise is measured at 25.4 μV/√Hz at 100 Hz and the power supply rejection ratio exceeds 56 dB. Tuning tests reveal that the proposed transconductor allows for programming the control voltage of the remaining gate terminals to adjust the Gm value, compensating for variations in process, voltage, and temperature.
- 16 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (14) , 26806-26813
A 0.88-nW Ultralow Gm Tunable Transconductor Based on Bootstrap Body Input for Biomedical Sensors
Low-transconductance (Gm) amplifiers are essential for implementing low-frequency continuous-time filters, a critical aspect for biomedical sensors. This paper proposes a low-power, low-Gm amplifier based on the bootstrap-body-input technique. The input topology of the transconductor consists of two transistors with body-inputs and a source degeneration resistor. The source of the two transistors connected to the resistor, which bootstraps the terminal voltages and expands the input range. To further reduce the Gm value of the transconductor, an area-efficient series-parallel current mirror is adopted. The transconductor was fabricated in a 0.18 μm CMOS process. Measurement results show that the bootstrap-body-input transconductor achieves a reduction in Gm value of more than 1200 times over conventional body-input transconductor. The proposed transconductor features a tuning range of 27 to 581 pA/V at 0.8 V supply voltage, with a power consumption of only 0.88 nW. The input-referred noise is measured at 25.4 μV/√Hz at 100 Hz and the power supply rejection ratio exceeds 56 dB. Tuning tests reveal that the proposed transconductor allows for programming the control voltage of the remaining gate terminals to adjust the Gm value, compensating for variations in process, voltage, and temperature.
- 28 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (11) , 1510-1514
An Adaptive Dark Current Compensation Analog Front-End With Reconfigurable Transimpedance Amplifier for Fluorescence Temperature Sensors
Abstract.In this brief, a low-power CMOS analog front-end (AFE) circuit is proposed for fluorescence optical fiber temperature sensors. The CMOS AFE utilizes a novel adaptive dark current compensation technique to eliminate static operating point offsets in the front-end circuit, which occur due to the quick increases of photodiode dark current at high temperatures. The reconfigurable transimpedance amplifier (TIA) supports both high and low gain modes. Fabricated using a 180nm CMOS process, the AFE chip exhibits a -3dB bandwidth of 10kHz, a transimpedance gain of 158.51dBΩ, and an inputreferred noise current of 14.89fA/Hz in its high gain mode. Under a 3.3V power supply, the circuit consumes 62.4μW in this mode. The temperature sensor prototype utilizing this AFE chip achieves high-precision measurements, with an average error of -0.1 ∘C and a standard deviation of 0.33 ∘C across a range from -30 ∘C to 100 ∘C.
- 28 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (11) , 1510-1514
An Adaptive Dark Current Compensation Analog Front-End With Reconfigurable Transimpedance Amplifier for Fluorescence Temperature Sensors
Abstract.In this brief, a low-power CMOS analog front-end (AFE) circuit is proposed for fluorescence optical fiber temperature sensors. The CMOS AFE utilizes a novel adaptive dark current compensation technique to eliminate static operating point offsets in the front-end circuit, which occur due to the quick increases of photodiode dark current at high temperatures. The reconfigurable transimpedance amplifier (TIA) supports both high and low gain modes. Fabricated using a 180nm CMOS process, the AFE chip exhibits a -3dB bandwidth of 10kHz, a transimpedance gain of 158.51dBΩ, and an inputreferred noise current of 14.89fA/Hz in its high gain mode. Under a 3.3V power supply, the circuit consumes 62.4μW in this mode. The temperature sensor prototype utilizing this AFE chip achieves high-precision measurements, with an average error of -0.1 ∘C and a standard deviation of 0.33 ∘C across a range from -30 ∘C to 100 ∘C.
- 27 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-9
A Dual-Channel Pseudo-Differential CMOS AFE for Fluorescence Optical Fiber Temperature Measurement
The escalating importance of temperature monitoring across industrial production, medical diagnostics, and environmental surveillance poses significant challenges for temperature sensing technologies, particularly in detection precision, electromagnetic interference resilience, and environmental adaptability. In response to these challenges, this paper proposes an integrated solution for fluorescence optical fiber temperature sensors, based on a 0.18μm CMOS process. The proposed approach uses a dual-channel pseudo-differential analog frontend (AFE) based on a pre-current transimpedance amplifier (PC-TIA). The CMOS AFE employs a novel zero-bias single photodiode (PD) fluorescence detection architecture, enabling differential light detection from a single incident light beam. This results in improved system reliability and measurement accuracy. The proposed pre-current amplifier uses complementary transistors to achieve highly linear amplification of differential current signals. A transimpedance amplifier converts the amplified current into a voltage signal. By employing a dc offset cancellation (DCOC), it effectively solves the issues related to the DC offset voltage at the input stage and the dark current of the PD. Measurement results indicate that the proposed CMOS AFE circuit attains a transimpedance gain of 152.03dBΩ, along with a -3dB bandwidth of 4kHz and an input-referred noise (IRN) current spectral density of 56.3fA/√Hz. These parameters highlight the system's exceptional capability for high-precision temperature measurements. The prototype chip achieved a maximum differential output swing of 3.25 Vpp,out, validated using both electrical and optical measurement setups. With a temperature range from -30°C to 100°C, the proposed temperature sensor prototype exhibited an average error of -0.19°C and a measurement standard deviation of 0.29°C.
- 27 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-9
A Dual-Channel Pseudo-Differential CMOS AFE for Fluorescence Optical Fiber Temperature Measurement
The escalating importance of temperature monitoring across industrial production, medical diagnostics, and environmental surveillance poses significant challenges for temperature sensing technologies, particularly in detection precision, electromagnetic interference resilience, and environmental adaptability. In response to these challenges, this paper proposes an integrated solution for fluorescence optical fiber temperature sensors, based on a 0.18μm CMOS process. The proposed approach uses a dual-channel pseudo-differential analog frontend (AFE) based on a pre-current transimpedance amplifier (PC-TIA). The CMOS AFE employs a novel zero-bias single photodiode (PD) fluorescence detection architecture, enabling differential light detection from a single incident light beam. This results in improved system reliability and measurement accuracy. The proposed pre-current amplifier uses complementary transistors to achieve highly linear amplification of differential current signals. A transimpedance amplifier converts the amplified current into a voltage signal. By employing a dc offset cancellation (DCOC), it effectively solves the issues related to the DC offset voltage at the input stage and the dark current of the PD. Measurement results indicate that the proposed CMOS AFE circuit attains a transimpedance gain of 152.03dBΩ, along with a -3dB bandwidth of 4kHz and an input-referred noise (IRN) current spectral density of 56.3fA/√Hz. These parameters highlight the system's exceptional capability for high-precision temperature measurements. The prototype chip achieved a maximum differential output swing of 3.25 Vpp,out, validated using both electrical and optical measurement setups. With a temperature range from -30°C to 100°C, the proposed temperature sensor prototype exhibited an average error of -0.19°C and a measurement standard deviation of 0.29°C.
- 21 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (7) , 878-882
An 88.96 dB HDR CMOS Image Sensor Modeled on Visual Neuronal Response
This brief proposes a low-voltage low-power high dynamic range (HDR) CMOS image sensor (CIS) with visual neuronal responses (VNR) tailored for IoT applications, especially biomedical scenarios, which demand low power consumption and limited transmission bandwidth. The proposed CIS modeled on the nonlinear compression characteristics of illumination in the visual nervous system to enhance the dynamic range (DR). By employing a dynamic readout of pixel signals and comparing with a reference ramp voltage, the output of the proposed CIS conforms to the Naka-Rushton function, which describes the response features of visual neurons. The proposed CIS adopts a column-parallel architecture to enable simultaneous exposure, readout, and quantization of pixels in each row, combined with several low-power reset circuits to reduce image lag and inter-row crosstalk. A 126 × 64 HDR CIS with a 6.6 μm pixel pitch was fabricated using a 180 nm CMOS technology. Measurement results show a DR exceeding 88.96 dB, with a total power consumption of 18.62 μJW at 60 fps and 0.8 V supply.
- 21 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (7) , 878-882
An 88.96 dB HDR CMOS Image Sensor Modeled on Visual Neuronal Response
This brief proposes a low-voltage low-power high dynamic range (HDR) CMOS image sensor (CIS) with visual neuronal responses (VNR) tailored for IoT applications, especially biomedical scenarios, which demand low power consumption and limited transmission bandwidth. The proposed CIS modeled on the nonlinear compression characteristics of illumination in the visual nervous system to enhance the dynamic range (DR). By employing a dynamic readout of pixel signals and comparing with a reference ramp voltage, the output of the proposed CIS conforms to the Naka-Rushton function, which describes the response features of visual neurons. The proposed CIS adopts a column-parallel architecture to enable simultaneous exposure, readout, and quantization of pixels in each row, combined with several low-power reset circuits to reduce image lag and inter-row crosstalk. A 126 × 64 HDR CIS with a 6.6 μm pixel pitch was fabricated using a 180 nm CMOS technology. Measurement results show a DR exceeding 88.96 dB, with a total power consumption of 18.62 μJW at 60 fps and 0.8 V supply.