Martin Ostermann
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Martin Ostermann has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Dirk Cremer
Software Development INTEGRAL, FGH GmbH, Mannheim, Germany
1 shared publication- Eliza Biala
University of Stuttgart
1 shared publication Hendrik Acker
Chair for Energy Systems and Energy Management, University of Kaiserslautern, Kaiserslautern, Germany
1 shared publicationKalaivanan Amudhan
University of Stuttgart
1 shared publicationWilli Heckmann
Software Development INTEGRAL, FGH GmbH, Mannheim, Germany
1 shared publicationWolfram H. Wellssow
Chair for Energy Systems and Energy Management, University of Kaiserslautern, Kaiserslautern, Germany
1 shared publication
Latest Publications
- Open Access
- 27 May 2025
- Published by Cambridge University Press (CUP) in Cambridge Open Engage
Design’n’Grow Studio - explorations in upscaled biofabrication
Scaling up mycelium Engineered Living Materials (ELMs) presents opportunities and challenges for architectural design, particularly in understanding scale-related and unrelated properties of constructing with living materials. While Mycelium-Based Composites (MBCs) offer promising physical properties and environmental benefits , their scalability remains underexplored. Previous studies (Le Ferrand, 2024; Elsacker, 2022; Ross, 2016) identified oxygen and carbon dioxide penetration as limiting factors, constraining mycelium growth beyond a depth of 15 cm. Bio-welding techniques have enabled the creation of larger blocks (400 × 550 × 400 mm) (Elsacker, 2022), addressing some of these challenges. This research employs a hands-on experimental approach, constructing large-scale (200 × 80 cm) demonstrators to investigate bio-welding and air penetration constraints. Moving beyond volumetric mass, the study explores speculative fabrication strategies for facade panels, allowing for geometric customization within the biofabrication process. Three methods were tested: (1) sacrificial molding with textile sheets, (2) bio-welding of textile-mycelium filaments, and (3) bio-welding of mycelium blocks. Using a consistent mycelium mixture (80 wt% sawdust, 20 wt% straw, and Ganoderma lucidum), additional additives (2 wt% guar gum, 1 wt% psyllium husk) facilitated extrusion-based filament production. Results showed successful large-scale mycelium growth with minimal contamination. Method (1) yielded strong bio-welding but posed drying challenges. Method (2) faced alignment and humidity control issues, while method (3) demonstrated partial success but structural weaknesses. The study highlights grassroots experimentation’s potential in scaling up MBCs while underscoring the need for further research into process refinement and scientific rigor.
- 27 May 2025
- Published by Cambridge University Press (CUP) in Cambridge Open Engage
Open AccessDesign’n’Grow Studio - explorations in upscaled biofabrication
Scaling up mycelium Engineered Living Materials (ELMs) presents opportunities and challenges for architectural design, particularly in understanding scale-related and unrelated properties of constructing with living materials. While Mycelium-Based Composites (MBCs) offer promising physical properties and environmental benefits , their scalability remains underexplored. Previous studies (Le Ferrand, 2024; Elsacker, 2022; Ross, 2016) identified oxygen and carbon dioxide penetration as limiting factors, constraining mycelium growth beyond a depth of 15 cm. Bio-welding techniques have enabled the creation of larger blocks (400 × 550 × 400 mm) (Elsacker, 2022), addressing some of these challenges. This research employs a hands-on experimental approach, constructing large-scale (200 × 80 cm) demonstrators to investigate bio-welding and air penetration constraints. Moving beyond volumetric mass, the study explores speculative fabrication strategies for facade panels, allowing for geometric customization within the biofabrication process. Three methods were tested: (1) sacrificial molding with textile sheets, (2) bio-welding of textile-mycelium filaments, and (3) bio-welding of mycelium blocks. Using a consistent mycelium mixture (80 wt% sawdust, 20 wt% straw, and Ganoderma lucidum), additional additives (2 wt% guar gum, 1 wt% psyllium husk) facilitated extrusion-based filament production. Results showed successful large-scale mycelium growth with minimal contamination. Method (1) yielded strong bio-welding but posed drying challenges. Method (2) faced alignment and humidity control issues, while method (3) demonstrated partial success but structural weaknesses. The study highlights grassroots experimentation’s potential in scaling up MBCs while underscoring the need for further research into process refinement and scientific rigor.
- 16 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Advanced model of static var compensators for power flow calculations
With a decrease of thermal generation units, reactive power compensation systems (RPCS) are more frequently utilized as controllable reactive power sources. Currently used Static Var Compensator (SVC) models only offer reactive power provision. With the increasing number of RPCS their significance in economic considerations rises. In order to enable the calculation of operational costs, this paper presents a model of a SVC which provides a projection of active power losses and how to implement them into power flow programs.
- 16 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Advanced model of static var compensators for power flow calculations
With a decrease of thermal generation units, reactive power compensation systems (RPCS) are more frequently utilized as controllable reactive power sources. Currently used Static Var Compensator (SVC) models only offer reactive power provision. With the increasing number of RPCS their significance in economic considerations rises. In order to enable the calculation of operational costs, this paper presents a model of a SVC which provides a projection of active power losses and how to implement them into power flow programs.