Yan Wen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yan Wen has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Lechun Xie
Wuhan University of Technology
2 shared publications Liqiang Wang
State Key Laboratory of Metal Matrix Composites School of Materials Science and Engineering Shanghai Jiao Tong University Shanghai 200240 P. R. China
2 shared publicationsChanglin Huang
State Key Laboratory of Superalloy and Application Technology Wuhan University of Technology Wuhan 430070 P. R. China
1 shared publicationChaoyi Ding
State Key Laboratory of Superalloy and Application Technology Wuhan University of Technology Wuhan 430070 P. R. China
1 shared publicationLin Hua
State Key Laboratory of Superalloy and Application Technology Wuhan University of Technology Wuhan 430070 P. R. China
1 shared publicationShiqiang Xie
State Key Laboratory of Superalloy and Application Technology Wuhan University of Technology Wuhan 430070 P. R. China
1 shared publication
Latest Publications
- 16 January 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (4)
Repairing Mechanism of Fatigue Defects in TiB/Ti‐6Al‐4V Titanium Matrix Composite via Electroshock Treatment
Titanium matrix composites (TMCs) can be used in some important industrial fields, and they are easy to generate the defects during loading. It is significant to modify the microstructure and repair the defects. In this article, the microstructure of secondary α (α s ) phase precipitated from the β phase via electroshock treatment (EST) in TiB/Ti‐6Al‐4V. The orientation of α phase and TiB varied, the maximum texture intensity of α phase decreased, and the orientation became more uniform. The maximum texture intensity of TiB increased. After EST, the yield strength of TiB/Ti‐6Al‐4V increased by 1345.7 MPa, the compressive fracture strain is 20.5%, and the hardness value is 420.4 HV. During the process of fatigue failure, the tips of TiB are easy to form micropores and defects. However, the fatigue defects can be repaired by EST, and the volume rate of repairing defects reached 73.94%–82.17%. All results indicate EST is an efficient method to repair defects and improve mechanical properties of TMCs.
- 16 January 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (4)
Repairing Mechanism of Fatigue Defects in TiB/Ti‐6Al‐4V Titanium Matrix Composite via Electroshock Treatment
Titanium matrix composites (TMCs) can be used in some important industrial fields, and they are easy to generate the defects during loading. It is significant to modify the microstructure and repair the defects. In this article, the microstructure of secondary α (α s ) phase precipitated from the β phase via electroshock treatment (EST) in TiB/Ti‐6Al‐4V. The orientation of α phase and TiB varied, the maximum texture intensity of α phase decreased, and the orientation became more uniform. The maximum texture intensity of TiB increased. After EST, the yield strength of TiB/Ti‐6Al‐4V increased by 1345.7 MPa, the compressive fracture strain is 20.5%, and the hardness value is 420.4 HV. During the process of fatigue failure, the tips of TiB are easy to form micropores and defects. However, the fatigue defects can be repaired by EST, and the volume rate of repairing defects reached 73.94%–82.17%. All results indicate EST is an efficient method to repair defects and improve mechanical properties of TMCs.
- 25 May 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (13)
Microstructure and Tribological Properties of Laser Melting Deposited Ti‐6Al‐4V Coating on Cu‐Cr‐Zr Substrate
Copper alloys are extensively utilized in electronics, electrical, and transportation because of their outstanding thermal and electrical conductivity. However, their low hardness and wear resistance restrict their utilization in some special environments. To address these issues, laser melting deposition (LMD) is utilized to fabricate Ti‐6Al‐4V coating on Cu‐Cr‐Zr substrate. The microstructure and mechanical properties of the interface between the coating and the substrate are analyzed. The results show that the composition of the transition zone is highly eutectic, mainly composed of Cu3Ti2 and Cu4Ti. The LMD‐constructed Ti‐6Al‐4V/Cu‐Cr‐Zr (TC4/Cu‐Cr‐Zr) has a shear strength of 101.11 MPa and a shear deformation strain of more than 23%. In terms of wear resistance, the wear rate of the coating is measured at 8.29 × 10−5 mm3 N−1 m−1 under a 5 N load, which represents a 64.27% reduction compared to that of the substrate. The microhardness of the coating increased by a factor of 3.84 compared to that of the substrate. In general, Cu was melted into the titanium coating under LMD. The intermetallic compounds generated by reaction between Cu and titanium promoted the coating bonding strength, and the titanium coating improved the wear resistance of the copper alloy.
- 25 May 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (13)
Microstructure and Tribological Properties of Laser Melting Deposited Ti‐6Al‐4V Coating on Cu‐Cr‐Zr Substrate
Copper alloys are extensively utilized in electronics, electrical, and transportation because of their outstanding thermal and electrical conductivity. However, their low hardness and wear resistance restrict their utilization in some special environments. To address these issues, laser melting deposition (LMD) is utilized to fabricate Ti‐6Al‐4V coating on Cu‐Cr‐Zr substrate. The microstructure and mechanical properties of the interface between the coating and the substrate are analyzed. The results show that the composition of the transition zone is highly eutectic, mainly composed of Cu3Ti2 and Cu4Ti. The LMD‐constructed Ti‐6Al‐4V/Cu‐Cr‐Zr (TC4/Cu‐Cr‐Zr) has a shear strength of 101.11 MPa and a shear deformation strain of more than 23%. In terms of wear resistance, the wear rate of the coating is measured at 8.29 × 10−5 mm3 N−1 m−1 under a 5 N load, which represents a 64.27% reduction compared to that of the substrate. The microhardness of the coating increased by a factor of 3.84 compared to that of the substrate. In general, Cu was melted into the titanium coating under LMD. The intermetallic compounds generated by reaction between Cu and titanium promoted the coating bonding strength, and the titanium coating improved the wear resistance of the copper alloy.