Weiwei Xu
Research Subjects
Weiwei Xu has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Lin Cheng
University of Science and Technology of China
4 shared publications - Dongfang Pan
University of Science and Technology of China
2 shared publications Yufa Zhou
Hefei CLT Microelectronics Ltd., Hefei, China
2 shared publicationsAoyang Li
School of Microelectronics, University of Science and Technology of China, Hefei, China
1 shared publication- Changjin Chen
School of Microelectronics, University of Science and Technology of China, Hefei, China
1 shared publication Ji Jin
School of Microelectronics, University of Science and Technology of China, Hefei, China
1 shared publication
Latest Publications
- 3 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (2) , 1663-1676
A Single-Mode Buck–Boost Converter With Always-Dual-Path Operation for Inductor Current Reduction
This article presents a battery-to-3.4 V buck–boost converter designed for mobile devices. The converter employs two flying capacitors (CF1 and CF2), one inductor (L) and six switches. CF1 operates in parallel with the inductor to distribute input current during inductor energizing phase, while CF2 assists the inductor in transferring output current during the inductor de-energizing phase, ensuring the inductor current (IL) is always lower than the output current (IOUT). This configuration results in a single-mode controlled buck–boost converter, allowing smooth voltage conversion over the entire battery voltage range. Additionally, the maximum voltage stress on switches is limited to either VIN or VOUT, enabling the use of 5-V devices for all power switches. Furthermore, the continuous output current delivery alleviates the right-half-plane zero effect, leading to fast transient responses. The converter was fabricated in a 0.18-μm BCD process. Measurement results demonstrate that the converter achieves a peak efficiency of 97.3% using a bulky inductor with a DCR of 18 mΩ. The peak efficiency remains at 96.4% using a compact inductor with a DCR of 200 mΩ.
- 3 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (2) , 1663-1676
A Single-Mode Buck–Boost Converter With Always-Dual-Path Operation for Inductor Current Reduction
This article presents a battery-to-3.4 V buck–boost converter designed for mobile devices. The converter employs two flying capacitors (CF1 and CF2), one inductor (L) and six switches. CF1 operates in parallel with the inductor to distribute input current during inductor energizing phase, while CF2 assists the inductor in transferring output current during the inductor de-energizing phase, ensuring the inductor current (IL) is always lower than the output current (IOUT). This configuration results in a single-mode controlled buck–boost converter, allowing smooth voltage conversion over the entire battery voltage range. Additionally, the maximum voltage stress on switches is limited to either VIN or VOUT, enabling the use of 5-V devices for all power switches. Furthermore, the continuous output current delivery alleviates the right-half-plane zero effect, leading to fast transient responses. The converter was fabricated in a 0.18-μm BCD process. Measurement results demonstrate that the converter achieves a peak efficiency of 97.3% using a bulky inductor with a DCR of 18 mΩ. The peak efficiency remains at 96.4% using a compact inductor with a DCR of 200 mΩ.
- 20 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (2) , 651-661
A 24–20-V Isolated DC-DC Converter Using a Transformer-Based Supply-Generating Technique
This article introduces a 24–20-V isolated dc-dc converter that utilizes a transformer-based supply-generating technique to efficiently drive power transistors. Traditional high-voltage inverters with output voltages above 5 V typically require dedicated power converters, such as LDOs or buck converters, to supply power to gate drivers and control circuits, often leading to reduced efficiency and increased system costs. In this work, an efficient supply-generating technique that directly produces a 5-V power supply from an auxiliary coil—strategically positioned to harness energy from the primary coil—simplifies the power supply design and eliminates the need for external components. The transmitter (TX) and receiver (RX) were fabricated using a 0.18- $\mu $ m BCD process and packaged in a land grid array (LGA) package. Experimental results confirm that the converter achieves a peak efficiency of 73.2% and a power density of 36.5 mW/mm3. Compared to other integrated solutions, the proposed converter realizes a 13.2% efficiency improvement, and its electromagnetic interference (EMI) performance satisfies the CISPR-32 Class B standard on a two-layer PCB without any stitching capacitors.
- 20 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (2) , 651-661
A 24–20-V Isolated DC-DC Converter Using a Transformer-Based Supply-Generating Technique
This article introduces a 24–20-V isolated dc-dc converter that utilizes a transformer-based supply-generating technique to efficiently drive power transistors. Traditional high-voltage inverters with output voltages above 5 V typically require dedicated power converters, such as LDOs or buck converters, to supply power to gate drivers and control circuits, often leading to reduced efficiency and increased system costs. In this work, an efficient supply-generating technique that directly produces a 5-V power supply from an auxiliary coil—strategically positioned to harness energy from the primary coil—simplifies the power supply design and eliminates the need for external components. The transmitter (TX) and receiver (RX) were fabricated using a 0.18- $\mu $ m BCD process and packaged in a land grid array (LGA) package. Experimental results confirm that the converter achieves a peak efficiency of 73.2% and a power density of 36.5 mW/mm3. Compared to other integrated solutions, the proposed converter realizes a 13.2% efficiency improvement, and its electromagnetic interference (EMI) performance satisfies the CISPR-32 Class B standard on a two-layer PCB without any stitching capacitors.
- 9 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (6) , 2194-2205
A Battery-to-3.4 V Hybrid Buck-Boost Converter With Always Reduced Conduction Loss
This article presents a hybrid buck-boost converter designed for lithium-ion battery-powered mobile devices. The proposed converter consists of four low-voltage power switches and one flying capacitor ( $C_{\text{F}}$ ). Unlike the conventional buck-boost converters (CBBCs) that employ two power switches in series with an inductor, this converter uses only one. The $C_{\text{F}}$ , which is paralleled with the inductor ( $L$ ), facilitates charge transfer to the output capacitor in the buck mode and distributes input current in the boost mode. This configuration significantly reduces inductor current across the entire input voltage ( $V_{\text{IN}}$ ) range. By leveraging the low-voltage stress of power switches and reduced current stress of inductor, the conduction loss (CDL) of the power switches is reduced by up to 64% compared with other studies with equivalent silicon areas. The converter was fabricated with a 0.18 $\mu$ m bipolar-CMOS-DMOS (BCD) process using only 5-V devices. Measurement results show that the converter achieves a peak efficiency of 98.6% with a small dc resistance (DCR) of 8 m $\Omega$ and maintains a peak efficiency of 97.3% with a larger DCR of 170 m $\Omega$ . Moreover, the converter achieves an on-die current density of 1.47 A/mm $^{2}$ .
- 9 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (6) , 2194-2205
A Battery-to-3.4 V Hybrid Buck-Boost Converter With Always Reduced Conduction Loss
This article presents a hybrid buck-boost converter designed for lithium-ion battery-powered mobile devices. The proposed converter consists of four low-voltage power switches and one flying capacitor ( $C_{\text{F}}$ ). Unlike the conventional buck-boost converters (CBBCs) that employ two power switches in series with an inductor, this converter uses only one. The $C_{\text{F}}$ , which is paralleled with the inductor ( $L$ ), facilitates charge transfer to the output capacitor in the buck mode and distributes input current in the boost mode. This configuration significantly reduces inductor current across the entire input voltage ( $V_{\text{IN}}$ ) range. By leveraging the low-voltage stress of power switches and reduced current stress of inductor, the conduction loss (CDL) of the power switches is reduced by up to 64% compared with other studies with equivalent silicon areas. The converter was fabricated with a 0.18 $\mu$ m bipolar-CMOS-DMOS (BCD) process using only 5-V devices. Measurement results show that the converter achieves a peak efficiency of 98.6% with a small dc resistance (DCR) of 8 m $\Omega$ and maintains a peak efficiency of 97.3% with a larger DCR of 170 m $\Omega$ . Moreover, the converter achieves an on-die current density of 1.47 A/mm $^{2}$ .