SMStefan Ilie Moldovan

Stefan Ilie Moldovan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Stefan Ilie Moldovan has a total of 3 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Spacing Effects in Guided Vertical‐Axis Wind Turbine Arrays for Highway Energy Harvesting Under Multi‐Vehicle Wake Conditions

    by Aydin Ulus, Stefan Ilie Moldovan

    Highway‐induced airflow generated by passing vehicles represents an underutilized source of localized renewable energy that can be harvested using vertical‐axis wind turbines (VAWTs). While prior studies have demonstrated the feasibility of single‐turbine configurations, the aerodynamic interaction between vehicle wakes and multi‐turbine arrays—particularly the role of inter‐turbine spacing—remains insufficiently understood. In this study, two‐dimensional unsteady Reynolds‐averaged Navier–Stokes (URANS) simulations coupled with the SST k–ω turbulence model are employed to investigate the performance of guided elliptical Savonius‐type VAWT arrays operating under multi‐vehicle traffic conditions. Three‐turbine arrays are examined at normalized inter‐turbine spacings from S/D = 3 to 14, together with an additional phase‐aligned reference case at S/D = 30.114. The results reveal a strong non‐linear dependence of array‐level energy extraction on turbine spacing. Among the investigated configurations, the highest total energy capture is achieved at a spacing of 12 m (12D), yielding a total extracted energy of 697.34 J and representing a 68% increase relative to the most compact configuration. Smaller spacings are characterized by severe wake interference between turbines, whereas larger spacings exhibit progressive dissipation of vehicle‐induced flow structures despite near‐complete velocity recovery. Turbine 1 shows limited sensitivity to spacing, with an energy variation of approximately 14%, whereas Turbines 2 and 3 exhibit substantially greater variations of approximately 87% and more than 140%, respectively. The inclusion of guide vanes further enhances total energy extraction by approximately 80–120% across the investigated spacing range. These findings highlight the importance of coordinated inter‐turbine spacing and flow‐guiding strategies in maximizing energy harvesting from vehicle‐induced wakes and provide practical design guidance for the deployment of guided VAWT arrays in highway environments.

  • Open Access

    Blade Count and Rotational Speed Sensitivity of Vertical‐Axis Turbines Under Guided Vehicle‐Generated Transient Wakes

    by Aydin Ulus, Stefan Ilie Moldovan

    Vehicle wakes generate short but energetic gusts that can be used by small roadside turbines, yet the operating conditions that allow a rotor to take full advantage of these events are still not fully clear. Flow‐guiding structures that were previously shown to improve wake redirection and energy capture are employed in this study. However, the combined influence of blade count and prescribed rotational speed under true transient vehicle‐induced inflow has not been examined in a systematic way. In the present study, vertical‐axis turbines with two to six blades were evaluated numerically while a car traveling at 32 m/s produced the unsteady wake. The rotor speed was increased from the nominal value ω₀ = 6.677 rad/s (63.76 rpm, corresponding to a baseline tip‐speed ratio of approximately 0.10) up to 2.2ω₀. The results show a strong dependence of performance on both blade number and rotational speed. The two‐blade configuration provided the most consistent energy extraction and reached a maximum of 158.5 J at 2.1ω₀, representing a 24.5% increase relative to baseline speed. In contrast, higher‐solidity rotors experienced significant performance deterioration at elevated speeds, and several cases produced negative net energy. This behavior was linked to repeated interception of the wake core by returning blades at unfavorable angular positions, leading to transient torque reversal. The findings suggest that, under short‐duration vehicle wakes, low‐solidity rotors operated at carefully selected rotational speeds are more reliable than higher‐blade‐count configurations.


  • Open Access

    Investigating the Feasibility of 3D Printed Pressure Taps for Surface Pressure Measurements in Wind Tunnel Models

    by Eric Haake, Sahaj Thapa, Stefan Ilie Moldovan

    Pressure taps are commonly used in aerodynamics to measure the pressure distribution on the surface of objects in air flow and provide valuable information for the analysis of aerodynamic performance. However, traditional pressure tap technology has limitations in terms of customization and complexity, making it difficult to measure pressure in hard-to-reach regions or for complex geometries. This research investigated the feasibility of using 3D printed pressure taps for surface pressure measurements in aerodynamics and compared their performance with conventional pressure taps and Computational Fluids Dynamics (CFD) simulations. The study included designing and producing 3D printed pressure taps with customized shapes for airfoils and evaluating their performance in terms of accuracy and precision. The experimental methodology involved exploring the design of pressure taps for the NACA 2412 airfoil. The 3D printed pressure taps were effective in capturing the complex flow features around the airfoil. Moreover, the experimental findings exhibited a high degree of concurrence with the CFD simulation outcomes. The comparison of experimental and literature data revealed the typical characteristics of flow, including flow separation and a gradual increase in Cp before the onset of vortex shedding. The study demonstrated the potential of 3D printing technology to produce complex shapes with embedded pressure taps for reliable flow measurement. The findings allow the development of tools that provide useful understandings of the flow behavior around wind tunnel models which can be applied in the design and optimization of aerodynamic structures.

  • Open Access

    Optimization of Vertical Axis Wind Turbine Systems to Capture Vehicle-Induced Highway Winds

    by Aydin Ulus, Stefan Ilie Moldovan

    This study introduces an innovative set of guide vanes that increase the efficiency of Vertical Axis Wind Turbines (VAWT) using winds generated by vehicles traveling on highways. The increase in efficiency is based on enhancing the airflow interaction as the vehicle moves past the turbine. Initial Computational Fluid Dynamics (CFD) simulations with two guide vanes setups demonstrated a 56.81% increase in power output under wind generated by passenger vehicles. Further design enhancements, incorporating three guide vanes with optimized geometries, led to a 242% improvement in power generation. Additional simulations evaluated the performance under wind conditions generated by larger vehicles, such as buses. The three guide vanes configuration yielded a 102% increase in energy capture efficiency in these scenarios. The findings suggest that vehicle-induced winds—typically an untapped energy source—can be effectively harvested using tailored turbine system designs. By integrating passive flow control strategies such as guide vanes, VAWTs can operate more efficiently in highway environments. This research highlights a novel pathway for enhancing renewable energy systems and supports broader efforts toward sustainable energy development through the utilization of unconventional wind sources. This performance enhancement is primarily due to the aerodynamic redirection of airflow toward the advancing blade and away from the returning blade, reducing drag and improving torque generation.