Yin Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yin Zhou has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Haoxuan Ran
College of Materials Science and Engineering, Chongqing University, Chongqing 400044, People’s Republic of China
1 shared publication- Hua Su
School of Computer Science & Technology, Tiangong University, Tianjin 300387, China
1 shared publication J.-C. Paul
1 shared publication- Lan Li
Division of Sports Medicine and Adult Reconstructive Surgery, Department of Orthopedic Surgery, Nanjing Drum Tower Hospital, Affiliated Hospital of Medical School, Nanjing University, Nanjing, 210008, China
1 shared publication - Nirong Bao
Department of Orthopedics, Nanjing Jinling Hospital, Affiliated Hospital of Medical School, Nanjing University, Nanjing 210002, China
1 shared publication - Peng Wang
Department of Orthopedics, Shanghai Tenth People's Hospital, School of Medicine, Tongji University, Shanghai, 200072, China
1 shared publication
Latest Publications
- 25 June 2025
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 33 (5) , 055016
Study on the warm air bending of NM400TP wear-resistant steel sheets heated by online floating contact heating module
To address the challenge posed by the reduced cold formability of high-strength steel sheets in industrial applications, a novel warm air bending method utilizing an online local contact heating module was investigated. NM400TP high strength low alloy wear-resistant steel sheets were used in experiment and numerical simulation to verify the bending process. A thermo-mechanical coupled model, taking into account the material heterogeneity, was constructed to predict the bending outcomes under various conditions of temperatures and forming speeds. The results proved the validation of the new method in improving the bendability of NM400TP plates, and the model can reveal the heat transfer processes, heterogeneous deformation and fracture characteristics during warm air bending. In comparison to conventional cold air bending, warm air bending conditions with a stamping speed of 1000 mm min−1 and a temperature of 350 °C promoted 54% increase in the bending limit angle and a remarkable reduction in the forming load.
- 25 June 2025
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 33 (5) , 055016
Study on the warm air bending of NM400TP wear-resistant steel sheets heated by online floating contact heating module
To address the challenge posed by the reduced cold formability of high-strength steel sheets in industrial applications, a novel warm air bending method utilizing an online local contact heating module was investigated. NM400TP high strength low alloy wear-resistant steel sheets were used in experiment and numerical simulation to verify the bending process. A thermo-mechanical coupled model, taking into account the material heterogeneity, was constructed to predict the bending outcomes under various conditions of temperatures and forming speeds. The results proved the validation of the new method in improving the bendability of NM400TP plates, and the model can reveal the heat transfer processes, heterogeneous deformation and fracture characteristics during warm air bending. In comparison to conventional cold air bending, warm air bending conditions with a stamping speed of 1000 mm min−1 and a temperature of 350 °C promoted 54% increase in the bending limit angle and a remarkable reduction in the forming load.
- 22 April 2022
- Published by Springer Nature
- p. 1362-1371
Real-Time Demand Response Interactive Behavior Model of Electric Vehicle Cluster
- 22 April 2022
- Published by Springer Nature
- p. 1362-1371
Real-Time Demand Response Interactive Behavior Model of Electric Vehicle Cluster
- 1 December 2020
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 117, 111347
Modeling osteoinduction in titanium bone scaffold with a representative channel structure
- 1 December 2020
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 117, 111347
Modeling osteoinduction in titanium bone scaffold with a representative channel structure
- 1 August 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 158-163
Improved Algebraic Algorithm on Point projection for B´eziercurves
This paper presents an improved algebraic pruning method for point projection for Bezier curves. It first turns the point projection into a root finding problem, and provides a simple but easily overlooked method to avoid finding invalid roots which is obviously irrelative to the closest point. The continued fraction method and its expansion are utilized to strengthen its robustness. Since NURBS curves can be easily turned into Bezier form, the new method also works with NURBS curves. Examples are presented to illustrate the efficiency and robustness of the new method.
- 1 August 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 158-163
Improved Algebraic Algorithm on Point projection for B´eziercurves
This paper presents an improved algebraic pruning method for point projection for Bezier curves. It first turns the point projection into a root finding problem, and provides a simple but easily overlooked method to avoid finding invalid roots which is obviously irrelative to the closest point. The continued fraction method and its expansion are utilized to strengthen its robustness. Since NURBS curves can be easily turned into Bezier form, the new method also works with NURBS curves. Examples are presented to illustrate the efficiency and robustness of the new method.