Polina Poletaeva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Polina Poletaeva has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Aleksandr Agarkov
All-Russian Dairy Research Institute (VNIMI), 115093 Moscow, Russia
2 shared publications - O. B. Fedotova
All-Russian Dairy Research Institute (VNIMI), 115093 Moscow, Russia
2 shared publications - Sergey Sirotin
All-Russian Dairy Research Institute (VNIMI), 115093 Moscow, Russia
2 shared publications - Dmitriy Mikhailovich Myalenko
All-Russian Dairy Research Institute
1 shared publication - Dmitry Myalenko
All-Russian Dairy Research Institute (VNIMI), Russia
1 shared publication
Latest Publications
- Open Access
Tensile and Structural Properties of Antioxidant- and CaCO3-Modified Polyethylene Films
The demand for modified packaging materials increases annually. At the same time, there is growing interest in the development of functional packaging. The incorporation of modifiers, stabilizers, and fillers into polymer matrices can enhance the functionality of the material but may also negatively affect its safety. Polymers are susceptible to degradation, which negatively affects their strength and tensile properties under external factors (physical, chemical or environmental). Packaging containing antimicrobial and antioxidant agents is among the most promising, as it contributes to the product quality during storage. Films based on calcium carbonate (CaCO3) and dihydroquercetin (DHQ) remain insufficiently studied, despite their potential. Such materials are especially relevant for fatty products with a large contact surface area, including butter, cheese, and other solid high-fat foods. This study aimed to comprehensively investigate the structural and tensile properties of polyethylene films modified with varying contents of CaCO3 and DHQ. The films were produced via blown film extrusion using a laboratory extruder (SJ-28). Surface analysis was performed using scanning electron microscopy (SEM) and atomic force microscopy (AFM). Fourier-transform infrared (FTIR) spectroscopy was used to examine the film’s composition. The results showed that the introduction of more than 40.0 wt.% of CaCO3 into the polymer base affected the strength properties. The conducted studies of the physical and mechanical properties of LDPE film samples filled with CaCO3 showed significant changes in the samples containing more than 50.0 wt.% of the filler, with an increase in strength of more than 40.0%. The relative elongation at break after 50.0 wt.% decreased by more than 75.0%. These results indicate that to achieve the best strength properties for packaging materials, it is recommended to fill them to a maximum of 40.0 wt.%. The introduction of the antioxidant DHQ had almost no effect on the strength of the modified films. SEM analysis of films with high CaCO3 content and DHQ revealed visible antioxidant particles on the film surface, suggesting enhanced antioxidant potential at the interface between the film and dairy products. AFM analysis confirmed that a CaCO3 40.0 wt.% content altered the surface roughness and heterogeneity of the films. FTIR spectroscopy revealed that the incorporation of CaCO3 influenced the overall spectral profile of polyethylene, resulting in decreased peak intensities depending on the concentration of the filler. Based on these results, the modified polyethylene-based film with CaCO3 and DHQ shows potential for use as food packaging with antioxidant properties.
Open AccessTensile and Structural Properties of Antioxidant- and CaCO3-Modified Polyethylene Films
The demand for modified packaging materials increases annually. At the same time, there is growing interest in the development of functional packaging. The incorporation of modifiers, stabilizers, and fillers into polymer matrices can enhance the functionality of the material but may also negatively affect its safety. Polymers are susceptible to degradation, which negatively affects their strength and tensile properties under external factors (physical, chemical or environmental). Packaging containing antimicrobial and antioxidant agents is among the most promising, as it contributes to the product quality during storage. Films based on calcium carbonate (CaCO3) and dihydroquercetin (DHQ) remain insufficiently studied, despite their potential. Such materials are especially relevant for fatty products with a large contact surface area, including butter, cheese, and other solid high-fat foods. This study aimed to comprehensively investigate the structural and tensile properties of polyethylene films modified with varying contents of CaCO3 and DHQ. The films were produced via blown film extrusion using a laboratory extruder (SJ-28). Surface analysis was performed using scanning electron microscopy (SEM) and atomic force microscopy (AFM). Fourier-transform infrared (FTIR) spectroscopy was used to examine the film’s composition. The results showed that the introduction of more than 40.0 wt.% of CaCO3 into the polymer base affected the strength properties. The conducted studies of the physical and mechanical properties of LDPE film samples filled with CaCO3 showed significant changes in the samples containing more than 50.0 wt.% of the filler, with an increase in strength of more than 40.0%. The relative elongation at break after 50.0 wt.% decreased by more than 75.0%. These results indicate that to achieve the best strength properties for packaging materials, it is recommended to fill them to a maximum of 40.0 wt.%. The introduction of the antioxidant DHQ had almost no effect on the strength of the modified films. SEM analysis of films with high CaCO3 content and DHQ revealed visible antioxidant particles on the film surface, suggesting enhanced antioxidant potential at the interface between the film and dairy products. AFM analysis confirmed that a CaCO3 40.0 wt.% content altered the surface roughness and heterogeneity of the films. FTIR spectroscopy revealed that the incorporation of CaCO3 influenced the overall spectral profile of polyethylene, resulting in decreased peak intensities depending on the concentration of the filler. Based on these results, the modified polyethylene-based film with CaCO3 and DHQ shows potential for use as food packaging with antioxidant properties.
- Open Access
- 1 July 2025
- Published by MDPI AG in Preprints.org
Study of the Tensile and Structural Properties of Antioxidant CaCO3-Modified Polyethylene Films
The demand for modified packaging materials increases annually. At the same time, there is growing interest in the development of functional packaging. The incorporation of modifiers, stabilizers, and fillers into polymer matrices can enhance the functionality of the material but may also negatively affect its safety. Polymers are susceptible to degrada-tion, which negatively affects their strength and tensile properties under external factors (physical, chemical or environmental). Packaging containing antimicrobial and antioxi-dant agents is among the most promising, as it contributes to the product quality during storage. Films based on calcium carbonate (CaCO₃) and dihydroquercetin (DHQ) remain insufficiently studied, despite their potential. Such materials are especially relevant for fatty products with a large contact surface area, including butter, cheese, and other solid high-fat foods. Butter is often packaged under conditions that allow oxygen exposure, which initiates oxidative degradation on the surface. Antimicrobial and antioxidant agents in packaging can prevent oxidation. This study aimed to comprehensively inves-tigate the structural and tensile properties of polyethylene films modified with varying contents of CaCO₃ and DHQ. The films were produced via blown film extrusion using a laboratory extruder (SJ-28). Surface analysis was performed using scanning electron mi-croscopy (SEM) and atomic force microscopy (AFM). Fourier-transform infrared (FTIR) spectroscopy was used to examine the film's composition. Based on the results, the modi-fied polyethylene-based film with CaCO₃ and DHQ shows potential for use as food pack-aging with antioxidant properties. The obtained film demonstrated stability of tensile properties, which supports its suitability for reducing the risk of micro- and nanoplastic migration into food during storage.
- 1 July 2025
- Published by MDPI AG in Preprints.org
Open AccessStudy of the Tensile and Structural Properties of Antioxidant CaCO3-Modified Polyethylene Films
The demand for modified packaging materials increases annually. At the same time, there is growing interest in the development of functional packaging. The incorporation of modifiers, stabilizers, and fillers into polymer matrices can enhance the functionality of the material but may also negatively affect its safety. Polymers are susceptible to degrada-tion, which negatively affects their strength and tensile properties under external factors (physical, chemical or environmental). Packaging containing antimicrobial and antioxi-dant agents is among the most promising, as it contributes to the product quality during storage. Films based on calcium carbonate (CaCO₃) and dihydroquercetin (DHQ) remain insufficiently studied, despite their potential. Such materials are especially relevant for fatty products with a large contact surface area, including butter, cheese, and other solid high-fat foods. Butter is often packaged under conditions that allow oxygen exposure, which initiates oxidative degradation on the surface. Antimicrobial and antioxidant agents in packaging can prevent oxidation. This study aimed to comprehensively inves-tigate the structural and tensile properties of polyethylene films modified with varying contents of CaCO₃ and DHQ. The films were produced via blown film extrusion using a laboratory extruder (SJ-28). Surface analysis was performed using scanning electron mi-croscopy (SEM) and atomic force microscopy (AFM). Fourier-transform infrared (FTIR) spectroscopy was used to examine the film's composition. Based on the results, the modi-fied polyethylene-based film with CaCO₃ and DHQ shows potential for use as food pack-aging with antioxidant properties. The obtained film demonstrated stability of tensile properties, which supports its suitability for reducing the risk of micro- and nanoplastic migration into food during storage.