Jiaming An
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jiaming An has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Ali Emadi
Department of Electrical and Computer Engineering and McMaster Automotive Resource Centre (MARC), McMaster University, Hamilton, ON L8S 4L8, Canada
5 shared publications - Linke Zhou
McMaster Automotive Resource Centre (MARC), McMaster University, Hamilton, ON, Canada
5 shared publications - Yulei Wang
State Key Laboratory of Power Transmission Equipment Technology, School of Electrical Engineering, Chongqing University, Chongqing, China
5 shared publications - Di Wang
McMaster Automotive Resource Centre (MARC), McMaster University, Hamilton, ON, Canada
4 shared publications Piranavan Suntharalingam
4 shared publications- Giorgio Pietrini
McMaster Automotive Resource Centre (MARC), McMaster University, Hamilton, ON, Canada
3 shared publications
Latest Publications
- 4 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. PP, 1
DC EMI Filter With Characteristic Matching to Enhance Insertion Loss and Mitigate Mid-Frequency Degradation for High-Power Motor Drive Systems
EMI filters are a primary solution for mitigating conducted EMI emissions in high-power variable-speed motor drive (VSD) systems. However, significant mid-frequency (MF) degradation has been observed when a DC EMI filter is integrated into a VSD system. This paper investigates and identifies the mechanism behind this degradation, revealing that cross-coupling between the non-ideal characteristics of the filter output and the inverter input initiates the issue, with a pronounced mismatch in their MF characteristics accelerating the degradation process, eventually resulting in near-complete filter failure. To address this challenge, a two-stage y-cap design with characteristic matching is proposed. Through matching with the inverter input, the first stage achieves effective decoupling and mitigates MF degradation, while the second stage, in combination with a common-mode (CM) inductor, provides sufficient attenuation. Extensive experiments validate the effectiveness of the proposed characteristic-matching DC EMI filter, demonstrating an additional improvement of over 20 dB in CM insertion loss and 30 dB in DM insertion loss within the MF degradation region. This improvement ensures that the conducted EMI emissions of the high-power VSD system comply with the DO-160G standard limits.
- 4 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. PP, 1
DC EMI Filter With Characteristic Matching to Enhance Insertion Loss and Mitigate Mid-Frequency Degradation for High-Power Motor Drive Systems
EMI filters are a primary solution for mitigating conducted EMI emissions in high-power variable-speed motor drive (VSD) systems. However, significant mid-frequency (MF) degradation has been observed when a DC EMI filter is integrated into a VSD system. This paper investigates and identifies the mechanism behind this degradation, revealing that cross-coupling between the non-ideal characteristics of the filter output and the inverter input initiates the issue, with a pronounced mismatch in their MF characteristics accelerating the degradation process, eventually resulting in near-complete filter failure. To address this challenge, a two-stage y-cap design with characteristic matching is proposed. Through matching with the inverter input, the first stage achieves effective decoupling and mitigates MF degradation, while the second stage, in combination with a common-mode (CM) inductor, provides sufficient attenuation. Extensive experiments validate the effectiveness of the proposed characteristic-matching DC EMI filter, demonstrating an additional improvement of over 20 dB in CM insertion loss and 30 dB in DM insertion loss within the MF degradation region. This improvement ensures that the conducted EMI emissions of the high-power VSD system comply with the DO-160G standard limits.
- 23 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (2) , 3753-3766
Design of a High-Power-Density 1-MVA Three-Level Inverter for Electric Aircraft Propulsion
The development of megavolt-ampere (MVA)-class three-level inverters has become the focus in advancing electric aircraft propulsion (EAP) systems. In this article, a highly power-dense three-level inverter design is demonstrated, targeting 1-MVA output power at a 1.5-kV dc bus voltage. The design focuses on optimizing the inverter’s power density at both the system and component levels, including topology and component selection, power stage layout, lightweight bus bar design, as well as cooling system and electromagnetic interference (EMI) filter designs. Through comprehensive optimization, the designed inverter achieves a total weight of only 22.57 kg and a gravimetric power density of over 44.3 kVA/kg, setting a new benchmark for MVA-class EAP. A prototype has been fabricated and tested under laboratory conditions, with experimental results validating both the electrical and thermal performance of the proposed inverter, confirming its capability for high-efficiency operation in demanding aerospace environments.
- 23 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (2) , 3753-3766
Design of a High-Power-Density 1-MVA Three-Level Inverter for Electric Aircraft Propulsion
The development of megavolt-ampere (MVA)-class three-level inverters has become the focus in advancing electric aircraft propulsion (EAP) systems. In this article, a highly power-dense three-level inverter design is demonstrated, targeting 1-MVA output power at a 1.5-kV dc bus voltage. The design focuses on optimizing the inverter’s power density at both the system and component levels, including topology and component selection, power stage layout, lightweight bus bar design, as well as cooling system and electromagnetic interference (EMI) filter designs. Through comprehensive optimization, the designed inverter achieves a total weight of only 22.57 kg and a gravimetric power density of over 44.3 kVA/kg, setting a new benchmark for MVA-class EAP. A prototype has been fabricated and tested under laboratory conditions, with experimental results validating both the electrical and thermal performance of the proposed inverter, confirming its capability for high-efficiency operation in demanding aerospace environments.
- 10 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (5) , 7321-7334
Near-Magnetic Interference in Rogowski Coil for Power Electronic Applications: Mechanism and Mitigation
Rogowski coil (RC), valued for its high bandwidth, galvanic isolation, and ease of integration, is widely employed in high-speed integrated power electronics. However, near-magnetic interference (NMI) arising from inductive coupling with adjacent current sources is often underestimated, which undermines the RC’s robustness in crucial applications such as characterization, protection, and control. This article first reveals the inevitability of NMI in RCs. Building upon this, the mutual inductance equation between the RC and external interference sources is derived in detail, establishing a solid theoretical foundation for efficient and quantitative interference evaluation. The derivation methodology is further generalized to arbitrary points in space, allowing for the quantitative analysis of the effect when the circuit under test (CUT) is offset from the RC’s center. Theoretical analysis highlights the number of turns as a key factor, demonstrating that appropriately increasing it can effectively mitigate the influence of both external NMI and internal CUT eccentricity. The inherent design tradeoff between measurement bandwidth and interference immunity is further analyzed. Design guidelines for establishing the upper and lower limits of the number of turns are derived, and the differential mode rejection ratio is introduced as an intuitive metric to quantify the interference suppression capability. The accuracy of the proposed NMI model and the effectiveness of mitigation strategies are corroborated by Ansys Q3D simulations and extensive frequency- and time-domain experiments.
- 10 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (5) , 7321-7334
Near-Magnetic Interference in Rogowski Coil for Power Electronic Applications: Mechanism and Mitigation
Rogowski coil (RC), valued for its high bandwidth, galvanic isolation, and ease of integration, is widely employed in high-speed integrated power electronics. However, near-magnetic interference (NMI) arising from inductive coupling with adjacent current sources is often underestimated, which undermines the RC’s robustness in crucial applications such as characterization, protection, and control. This article first reveals the inevitability of NMI in RCs. Building upon this, the mutual inductance equation between the RC and external interference sources is derived in detail, establishing a solid theoretical foundation for efficient and quantitative interference evaluation. The derivation methodology is further generalized to arbitrary points in space, allowing for the quantitative analysis of the effect when the circuit under test (CUT) is offset from the RC’s center. Theoretical analysis highlights the number of turns as a key factor, demonstrating that appropriately increasing it can effectively mitigate the influence of both external NMI and internal CUT eccentricity. The inherent design tradeoff between measurement bandwidth and interference immunity is further analyzed. Design guidelines for establishing the upper and lower limits of the number of turns are derived, and the differential mode rejection ratio is introduced as an intuitive metric to quantify the interference suppression capability. The accuracy of the proposed NMI model and the effectiveness of mitigation strategies are corroborated by Ansys Q3D simulations and extensive frequency- and time-domain experiments.
- 30 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (4) , 4643-4658
Practical Thermal Solution for 1-MVA Three-Level ANPC Inverter in Aerospace Applications
In aerospace applications, high-performance cooling systems are essential to ensure the reliability of power inverters under extreme operating conditions. This paper presents the design and analysis of a practical pin-fin liquid cooling system for a 1 MVA silicon carbide (SiC)-based three-level active neutral point clamped (ANPC) inverter. The thermal and hydraulic performance was evaluated through finite element analysis (FEA) models of SiC power modules and computational fluid dynamics (CFD) simulations, confirming the heat transfer efficiency required for aerospace environments at 70°C coolant temperature. The cooling solution leverages a staggered pin-fin arrangement to improve heat transfer efficiency while maintaining manufacturability and cost-effectiveness. Two different cold plate configurations—series and parallel—were compared for uniform fluid distribution and cost-effectiveness. Special attention was also given to sealing design, ensuring reliability in preventing coolant leakage. The system effectively manages over 7.2 kW power loss, maintaining junction temperature Tj safely below the 150°C limit. Experimental tests validated the cooling system’s hydraulic and thermal performance, demonstrating its ability to handle high power losses with low pressure drop, making it a robust and cost-effective solution for high-power aerospace inverters.
- 30 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (4) , 4643-4658
Practical Thermal Solution for 1-MVA Three-Level ANPC Inverter in Aerospace Applications
In aerospace applications, high-performance cooling systems are essential to ensure the reliability of power inverters under extreme operating conditions. This paper presents the design and analysis of a practical pin-fin liquid cooling system for a 1 MVA silicon carbide (SiC)-based three-level active neutral point clamped (ANPC) inverter. The thermal and hydraulic performance was evaluated through finite element analysis (FEA) models of SiC power modules and computational fluid dynamics (CFD) simulations, confirming the heat transfer efficiency required for aerospace environments at 70°C coolant temperature. The cooling solution leverages a staggered pin-fin arrangement to improve heat transfer efficiency while maintaining manufacturability and cost-effectiveness. Two different cold plate configurations—series and parallel—were compared for uniform fluid distribution and cost-effectiveness. Special attention was also given to sealing design, ensuring reliability in preventing coolant leakage. The system effectively manages over 7.2 kW power loss, maintaining junction temperature Tj safely below the 150°C limit. Experimental tests validated the cooling system’s hydraulic and thermal performance, demonstrating its ability to handle high power losses with low pressure drop, making it a robust and cost-effective solution for high-power aerospace inverters.