Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ru Guo has a total of 19 co-authors. Here are the top co-authors by number of shared publications:

  • Hang Luo

    State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083, China

    3 shared publications
  • Xuefan Zhou

    Powder Metallurgy Research Institute, State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, China

    2 shared publications
  • Dou Zhang

    State Key Laboratory of Powder Metallurgy, Central South University Changsha 410083 Hunan Province China

    1 shared publication
  • Dou Zhang

    Powder Metallurgy Research Institute, State Key Laboratory of Powder Metallurgy Central South University Changsha Hunan China

    1 shared publication
  • Dou Zhang

    Powder Metallurgy Research Institute, State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, China

    1 shared publication
  • Fan Wang

    State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, China

    1 shared publication

Latest Publications

  • Open Access

    Spring-Induced Mechanical Strategy for High-Output, Flexible PAN-Based Piezoelectric Harvester

    by Quan Hu, Yueyue Yu, Ru Guo, Hang Luo

    The growing demand for wearable electronics and the Internet of Things (IoT) calls for flexible piezoelectric energy harvesters with substantially improved power output. Polyacrylonitrile (PAN) polymers, with their high polarization and excellent thermal stability, are among the most promising candidates for efficient flexible piezoelectric materials. However, the performance of existing PAN-based harvesters remains limited, and strategies for further enhancing their output are still insufficiently explored. Herein, this study aims to overcome the output bottleneck of PAN-based PENGs by implementing a novel mechanical excitation strategy. Using electrospun flexible PAN-BaTiO3 nanocomposite films, we systematically compared the electromechanical responses under conventional compression and impact modes. Real-time synchronized force–current measurements in compression mode revealed that the output current increases progressively with drive frequency (2–10 Hz). Specifically, the PENG with PAN-20 wt.% BaTiO3 achieved a peak current of 0.33 mA at 10 Hz, showing an approximately 7.9-fold enhancement over its pure PAN counterpart. More importantly, under 6 Hz impact excitation, the device exhibited a remarkable output current density of 1.0 mA cm−2 and a peak power density of 256.5 µW cm−2. This current density is 95 times higher than that in compression mode at a comparable frequency and surpasses the performance of most recently reported piezoelectric and triboelectric nanogenerators. With an effective area of 16 cm2, the PENG could simultaneously illuminate up to 275 commercial LEDs or 100 individual bulbs and maintained stable operation over 63,530 cycles. This work overcomes the output bottleneck in low-frequency energy harvesting and provides an effective pathway toward practical energy-harvesting applications.

  • Open Access

    All-Organic Quantum Dots-Boosted Energy Storage Density in PVDF-Based Nanocomposites via Dielectric Enhancement and Loss Reduction

    by Ru Guo, Xi Yuan, Xuefan Zhou, Haiyan Chen, Haoran Xie, Quan Hu, Hang Luo, Dou Zhang

    Dielectric capacitors offer immense application potential in advanced electrical and electronic systems with their unique ultrahigh power density. Polymer-based dielectric composites with high energy density are urgently needed to meet the ever-growing demand for the integration and miniaturization of electronic devices. However, the universal contradictory relationship between permittivity and breakdown strength in traditional ceramic/polymer nanocomposite still poses a huge challenge for a breakthrough in energy density. In this work, all-organic carbon quantum dot CDs were synthesized and introduced into a poly(vinylidene fluoride) PVDF polymer matrix to achieve significantly boosted energy storage performance. The ultrasmall and surface functionalized CDs facilitate the polar β-phase transition and crystallinity of PVDF polymer and modulate the energy level and traps of the nanocomposite. Surprisingly, a synergistic dielectric enhancement and loss reduction were achieved in CD/PVDF nanocomposite. For one thing, the improvement in εr and high-field Dm originates from the CD-induced polar transition and interface polarization. For another thing, the suppressed dielectric loss and high-field Dr are attributed to the conductive loss depression via the introduction of deep trap levels to capture charges. More importantly, Eb was largely strengthened from 521.9 kV mm−1 to 627.2 kV mm−1 by utilizing the coulomb-blockade effect of CDs to construct energy barriers and impede carrier migration. As a result, compared to the 9.9 J cm−3 for pristine PVDF, the highest discharge energy density of 18.3 J cm−3 was obtained in a 0.5 wt% CD/PVDF nanocomposite, which is competitive with most analogous PVDF-based nanocomposites. This study demonstrates a new paradigm of organic quantum dot-enhanced ferroelectric polymer-based dielectric energy storage performance and will promote its application for electrostatic film capacitors.


  • Open Access

    Electrospinning Synthesis of Na0.5Bi0.5TiO3 Nanofibers for Dielectric Capacitors in Energy Storage Application

    by Yuan Liu, Hang Luo, Zhe Gao, Haoran Xie, Ru Guo, Fan Wang, Xuefan Zhou, Jun Cao, Dou Zhang

    Dielectric composites based on ferroelectric ceramics nanofibers are attracting increasing attention in capacitor application. In this work, the sol–gel method and electrospinning technology are utilized to prepare one-dimensional Na0.5Bi0.5TiO3 (NBT) nanofibers, and the influence of electrospinning process parameters such as spinning voltage, liquid supply rate, and collector speed on the morphology and structure of nanofibers are systematically explored. The final optimized parameters include the applied voltage of 20 kV, the solution flow rate of 1 mL/h, and the collector’s rotation speed of 1500 rpm. The optimized NBT nanofibers are introduced into the PVDF polymer matrix for energy storage application. Owing to the enhanced interfacial polarization between PVDF matrix and NBT nanofibers with a high aspect ratio, the NBT–PVDF nanocomposites achieve a high discharge energy density of 14.59 J cm−3 and an energy efficiency of 53.69% at 490 kV mm−1, which are higher than those of pure PVDF, i.e., 10.26 J cm−3 and 48.17% at 420 kV mm−1, respectively. The results demonstrate that the strategy of synthesizing NBT nanofibers using the electrospinning method is of great potential for high-performance dielectric capacitor application.


  • 2D High-κ Dielectric Ceramic Nanoplatelets for Polymer Nanocomposite Capacitors

    by Hang Luo, Sheng Chen, Ru Guo, Xuefan Zhou, Dou Zhang

    Polymer-based capacitors have found a wide range of applications, including pulse power weapons, power transmission, transformation engineering, and 5G communication due to their high power density, fast charge and discharge speed, and long cycle life. Polymer-based composites with two-dimensional (2D) fillers often exhibit high breakdown strength, low dielectric loss, and high energy density. This chapter provides an overview of the latest developments with regard to the synthesis method of 2D nanoplatelets, the classification of polymer/2D nanoplatelet composites, and the role of the intrinsic properties of anisotropic nanoplatelets for composite design. The design strategies of 2D nanocomposites for dielectric and high energy storage properties are discussed in detail. Finite element simulation and phase-field simulation are used to determine the polarisation and electric filed distribution in the composites, and provide guidance for material design. The incorporation of 2D nanoplatelets into polymers is demonstrated as an effective route to achieve high energy density capacitors. Finally, the outlook and future perspectives for high-κ ceramic/polymer composites are presented.