Li-Chun Liao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Li-Chun Liao has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Gwo-Liang Liao
Department of Information Science and Management Systems, National Taitung University, 369, Section 2 University Road., Taitung, Taiwan, R.O.C.
3 shared publications - Bin-Chyi Tseng
ASUSTek Computer Inc., Taipei, Taiwan
1 shared publication - Chen-Yu Huang
Medical Physics Department, Hong Kong Sanatorium and Hospital, Hong Kong, China
1 shared publication Hsiang-Ying Chen
Chaoyang University of Technology
1 shared publication- Junrong Luo
Jiangxi Provincial Key Laboratory for Animal Health, Institute of Animal Population Health, College of Animal Science and Technology, Jiangxi Agricultural University, Nanchang, Jiangxi, China
1 shared publication Kun-Chang Chien
Chaoyang University of Technology
1 shared publication
Latest Publications
- 13 October 2025
- Published by World Scientific Pub Co Pte Ltd in International Journal of Software Engineering and Knowledge Engineering
- Vol. 35 (12) , 1811-1832
Imperfect Debugging Software Reliability Model with Exponential and Linear Characteristics
This study aims to develop two generalized software reliability growth models (SRGMs) based on the non-homogeneous Poisson process (NHPP), considering the potential for imperfect debugging. The proposed models integrate both exponential and linear characteristics into the fault content function while accounting for varying fault detection rates. Additionally, numerical examples are provided to validate the effectiveness of the proposed models and compare their performance with existing ones. The results indicate that the proposed models offer more accurate prediction capabilities.
- 13 October 2025
- Published by World Scientific Pub Co Pte Ltd in International Journal of Software Engineering and Knowledge Engineering
- Vol. 35 (12) , 1811-1832
Imperfect Debugging Software Reliability Model with Exponential and Linear Characteristics
This study aims to develop two generalized software reliability growth models (SRGMs) based on the non-homogeneous Poisson process (NHPP), considering the potential for imperfect debugging. The proposed models integrate both exponential and linear characteristics into the fault content function while accounting for varying fault detection rates. Additionally, numerical examples are provided to validate the effectiveness of the proposed models and compare their performance with existing ones. The results indicate that the proposed models offer more accurate prediction capabilities.
- 23 September 2025
- Published by Taylor & Francis in Journal of the Chinese Institute of Engineers
- Vol. 49 (4) , 1107-1117
Design and implementation of a self-righting single-legged robot
- 23 September 2025
- Published by Taylor & Francis in Journal of the Chinese Institute of Engineers
- Vol. 49 (4) , 1107-1117
Design and implementation of a self-righting single-legged robot
- 3 July 2025
- Published by World Scientific Pub Co Pte Ltd in Journal of Advanced Manufacturing Systems
- Vol. 25 (04) , 645-664
Optimal Production Policies for Imperfect Processes with Repair, Rework, Outsourcing and Preventive Maintenance
This study integrates maintenance and production programs into the economic production quantity (EPQ) model for an imperfect process characterized by a deteriorating production system with an increasing hazard rate. Perfect repair and rework procedures are implemented following a production run failure. In such an imperfect process, defective items are produced and reworked and some are rejected after rework. The study evaluates the conditions of an EPQ model involving outsourcing to compensate for production shortfalls caused by waste products during reworking. Preventive maintenance (PM) is conducted after the “controlled” production phase and is categorized into renewal and regular PM. The probability of renewal PM is influenced by the number of regular PMs performed since the last system update cycle. The EPQ model is thus developed to determine the optimal production run time by minimizing total costs. Various cases are explored. A numerical example and sensitivity analysis will be presented to illustrate the model’s effectiveness. The findings indicate that enhancing maintenance capabilities can significantly lower production costs. Implementing a PM program contributes to a more efficient production system operation.
- 3 July 2025
- Published by World Scientific Pub Co Pte Ltd in Journal of Advanced Manufacturing Systems
- Vol. 25 (04) , 645-664
Optimal Production Policies for Imperfect Processes with Repair, Rework, Outsourcing and Preventive Maintenance
This study integrates maintenance and production programs into the economic production quantity (EPQ) model for an imperfect process characterized by a deteriorating production system with an increasing hazard rate. Perfect repair and rework procedures are implemented following a production run failure. In such an imperfect process, defective items are produced and reworked and some are rejected after rework. The study evaluates the conditions of an EPQ model involving outsourcing to compensate for production shortfalls caused by waste products during reworking. Preventive maintenance (PM) is conducted after the “controlled” production phase and is categorized into renewal and regular PM. The probability of renewal PM is influenced by the number of regular PMs performed since the last system update cycle. The EPQ model is thus developed to determine the optimal production run time by minimizing total costs. Various cases are explored. A numerical example and sensitivity analysis will be presented to illustrate the model’s effectiveness. The findings indicate that enhancing maintenance capabilities can significantly lower production costs. Implementing a PM program contributes to a more efficient production system operation.
- Open Access
- 1 January 2021
- Published by Chaoyang University of Technology (IJASE) in International Journal of Applied Science and Engineering
- Vol. 18 (5) , 1-8
Design and implementation of a snake-like robot with biomimetic 2-D gaits
For the purposes of field explorations and rescues, this research designed and implemented a simple snake-like robot that can move in narrow space and various terrains. The frame of the robot was constructed by modular segments. Each segment consisted interlocked rings, connecting rods and servo-motors that enabled the robot to bend and oscillate the body and imitate the 2-D gaits of snakes. We used Motoduino module, Bluetooth, servo-motors and wireless micro-camera to activate the robot. In order to cut down the cost, the robot’s skeleton and mechanical components were designed by 3-D printing using PLA material. The weight of the robot is about 960g and the size is 79cm×14cm×9cm. The maximum speed and the radius of gyration are about 16cm/sec and 21cm, respectively.
- 1 January 2021
- Published by Chaoyang University of Technology (IJASE) in International Journal of Applied Science and Engineering
- Vol. 18 (5) , 1-8
Open AccessDesign and implementation of a snake-like robot with biomimetic 2-D gaits
For the purposes of field explorations and rescues, this research designed and implemented a simple snake-like robot that can move in narrow space and various terrains. The frame of the robot was constructed by modular segments. Each segment consisted interlocked rings, connecting rods and servo-motors that enabled the robot to bend and oscillate the body and imitate the 2-D gaits of snakes. We used Motoduino module, Bluetooth, servo-motors and wireless micro-camera to activate the robot. In order to cut down the cost, the robot’s skeleton and mechanical components were designed by 3-D printing using PLA material. The weight of the robot is about 960g and the size is 79cm×14cm×9cm. The maximum speed and the radius of gyration are about 16cm/sec and 21cm, respectively.
- 1 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Design and Implementation of a Caterpillar Robot
This paper proposed a low cost worm-shape robot that can mimic the locomotion of a caterpillar to crawl by arching and stretching its body. Based on the process of implementing the caterpillar robot, the participated students can built up their interdisciplinary skills. Students have to integrate the technologies of micro-controllers, sensors, materials and mechanisms. We used a Motoduino U1 module to drive 4 servomotors and Bluetooth module to communicate between robot and users. In order to imitate gaits of caterpillars, the body of the robot was made by using discrete PVC rings to flexibly arch. The robot also can be remotely controlled to crawl forward/back or right/left, and change its height of arched back. The weight and total length of the robot were bout 470g and 65cm, respectively. The experiment shows that when the caterpillar robot moves in line, the averaged speed of robot can be 25m/hr. The maximum rotating angle is 30° and the minimum rotating diameter is 120cm.
- 1 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Design and Implementation of a Caterpillar Robot
This paper proposed a low cost worm-shape robot that can mimic the locomotion of a caterpillar to crawl by arching and stretching its body. Based on the process of implementing the caterpillar robot, the participated students can built up their interdisciplinary skills. Students have to integrate the technologies of micro-controllers, sensors, materials and mechanisms. We used a Motoduino U1 module to drive 4 servomotors and Bluetooth module to communicate between robot and users. In order to imitate gaits of caterpillars, the body of the robot was made by using discrete PVC rings to flexibly arch. The robot also can be remotely controlled to crawl forward/back or right/left, and change its height of arched back. The weight and total length of the robot were bout 470g and 65cm, respectively. The experiment shows that when the caterpillar robot moves in line, the averaged speed of robot can be 25m/hr. The maximum rotating angle is 30° and the minimum rotating diameter is 120cm.
- 1 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 1-10
Switching flow-graph modeling technique for DC-DC Ćuk converters
In this paper, the switching flow-graph models are developed to study the nonlinear behavior of DC-DC switching converters. Based on the concept of virtual switches and virtual switching functions, switching flow-graph (SFG) model are created easily without complex mathematics. The SFG modeling technique is helpful for undergraduate students or beginners to understand how the switching converters operate on different switching states. The students can also learn how to develop a model to observe the cause-effect relationship between the converter's variables. In this research, the basic Ćuk converter is used as an example to reveal the dynamic behavior of the DC-DC switching converters operated in DCM or CCM. The students can further enhance their concept of circuit design by developing the SFG model in software to simulate various conditions.
- 1 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 1-10
Switching flow-graph modeling technique for DC-DC Ćuk converters
In this paper, the switching flow-graph models are developed to study the nonlinear behavior of DC-DC switching converters. Based on the concept of virtual switches and virtual switching functions, switching flow-graph (SFG) model are created easily without complex mathematics. The SFG modeling technique is helpful for undergraduate students or beginners to understand how the switching converters operate on different switching states. The students can also learn how to develop a model to observe the cause-effect relationship between the converter's variables. In this research, the basic Ćuk converter is used as an example to reveal the dynamic behavior of the DC-DC switching converters operated in DCM or CCM. The students can further enhance their concept of circuit design by developing the SFG model in software to simulate various conditions.