Raphael Felca Glória
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Raphael Felca Glória has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Maisa Tonon Bitti Perazzini
3 shared publications- Hugo Perazzini
Institute of Natural Resources, Federal University of Itajubá, Itajubá, Brazil
2 shared publications Aline Tathyana Alves Felca
1 shared publication- Aline Tathyana Alves Felca1 shared publication
- Anderson Weslei da Cruz
Instituto Federal do Sudeste de Minas Gerais, Brasil; Universidade Federal de Itajubá, Brasil
1 shared publication - Flavio Bentes Freire
Civil Construction Academic Department, The Federal University of Technology – Paraná (UTFPR), Curitiba, Brazil
1 shared publication
Latest Publications
- Open Access
- 22 September 2026
- Published by Elsevier in Thermal Science and Engineering Progress
- Vol. 79
Efficiency analysis and evaluation 4E of a hybrid solar photovoltaic-electric dryer for Brewer’s Spent Grain drying
- 22 September 2026
- Published by Elsevier in Thermal Science and Engineering Progress
- Vol. 79
Open AccessEfficiency analysis and evaluation 4E of a hybrid solar photovoltaic-electric dryer for Brewer’s Spent Grain drying
- Open Access
- 20 February 2026
- Published by Elsevier in SSRN Electronic Journal
EFFICIENCY ANALYSIS AND EVALUATION 4E OF A HYBRID SOLAR PHOTOVOLTAIC-ELECTRIC DRYER FOR BREWER'S SPENT GRAIN DRYING
Brewer's Spent Grain (BSG) has high initial moisture it represents a significant environmental liability, but when properly dried, it BSG constitutes a biomass with a high heating value that can be used as an energy source. Since drying is one of the most energy-intensive stages in the agro-industrial chain, this work analyzed a hybrid solar dryer that incorporates solar thermal energy and a photovoltaic (PV) system with battery storage, supplying forced convection and auxiliary electric heating. The system’s performance was evaluated using four key indicators – energy, exergy, economic, and environmental (4E) analyses. Results showed that the overall drying efficiency ranged from 9.51 to 13.16%. The process, which involved operating the electric resistance heater at two power levels and during the night period, resulted in the highest specific energy consumption (7.01 kWh kg-1) and the lowest exergy performance (1.0%). In contrast, continuous electric heating increased the outlet exergy (3.08%) and reduced the specific energy consumption (6.61 kWh kg-1). The economic analysis indicated a payback period of approximately 3.72 years, along with a mitigation of up to 2.0 tons of CO2 emissions over a 10-year lifetime. The environmental return was estimated at 6.35 years. The dried BSG from continuous electrical heating processes showed an energy potential exceeding 15.0 MJ kg-1, demonstrating that the use of the hybrid solar PV-electric dryer can generate biomass with high energy content and support a more sustainable economy.
- 20 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEFFICIENCY ANALYSIS AND EVALUATION 4E OF A HYBRID SOLAR PHOTOVOLTAIC-ELECTRIC DRYER FOR BREWER'S SPENT GRAIN DRYING
Brewer's Spent Grain (BSG) has high initial moisture it represents a significant environmental liability, but when properly dried, it BSG constitutes a biomass with a high heating value that can be used as an energy source. Since drying is one of the most energy-intensive stages in the agro-industrial chain, this work analyzed a hybrid solar dryer that incorporates solar thermal energy and a photovoltaic (PV) system with battery storage, supplying forced convection and auxiliary electric heating. The system’s performance was evaluated using four key indicators – energy, exergy, economic, and environmental (4E) analyses. Results showed that the overall drying efficiency ranged from 9.51 to 13.16%. The process, which involved operating the electric resistance heater at two power levels and during the night period, resulted in the highest specific energy consumption (7.01 kWh kg-1) and the lowest exergy performance (1.0%). In contrast, continuous electric heating increased the outlet exergy (3.08%) and reduced the specific energy consumption (6.61 kWh kg-1). The economic analysis indicated a payback period of approximately 3.72 years, along with a mitigation of up to 2.0 tons of CO2 emissions over a 10-year lifetime. The environmental return was estimated at 6.35 years. The dried BSG from continuous electrical heating processes showed an energy potential exceeding 15.0 MJ kg-1, demonstrating that the use of the hybrid solar PV-electric dryer can generate biomass with high energy content and support a more sustainable economy.
- 16 July 2025
- Published by Elsevier in Thermal Science and Engineering Progress
- Vol. 65
Experimental and modeling study on solar drying of agroindustrial solid wastes
- 16 July 2025
- Published by Elsevier in Thermal Science and Engineering Progress
- Vol. 65
Experimental and modeling study on solar drying of agroindustrial solid wastes
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in REM - International Engineering Journal
- Vol. 78 (4)
Formation and performance of aluminized coatings on X22 steel by HAPC
X22 martensitic steel is widely used for its mechanical properties, but its high-temperature oxidation resistance is limited. This work investigates Halide Activated Pack Cementation (HAPC) as a surface treatment to improve this property. The process was performed using pure aluminum as the masteralloy, activated by NH4Cl, NaCl and KCl, with treatments at 650 °C and 800 °C for 16 h. Thermodynamic simulations supported the evaluation of aluminum deposition. At 650 °C, the salts failed to form suitable coatings. At 800 °C, aluminized layers of 75 µm (KCl) and 80 µm (NaCl) were obtained, with Fe-Al compositional gradients. Oxidation tests showed a significant improvement: mass gain was reduced from 13.55 mg/cm2 (uncoated) to 0.88 mg/cm2 for the KCl-activated coating and 0.90 mg/cm2 for the NaCl-activated coating. These results confirm the effectiveness of HAPC in enhancing oxidation resistance and extending the applicability of X22 steel in high-temperature environments.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in REM - International Engineering Journal
- Vol. 78 (4)
Open AccessFormation and performance of aluminized coatings on X22 steel by HAPC
X22 martensitic steel is widely used for its mechanical properties, but its high-temperature oxidation resistance is limited. This work investigates Halide Activated Pack Cementation (HAPC) as a surface treatment to improve this property. The process was performed using pure aluminum as the masteralloy, activated by NH4Cl, NaCl and KCl, with treatments at 650 °C and 800 °C for 16 h. Thermodynamic simulations supported the evaluation of aluminum deposition. At 650 °C, the salts failed to form suitable coatings. At 800 °C, aluminized layers of 75 µm (KCl) and 80 µm (NaCl) were obtained, with Fe-Al compositional gradients. Oxidation tests showed a significant improvement: mass gain was reduced from 13.55 mg/cm2 (uncoated) to 0.88 mg/cm2 for the KCl-activated coating and 0.90 mg/cm2 for the NaCl-activated coating. These results confirm the effectiveness of HAPC in enhancing oxidation resistance and extending the applicability of X22 steel in high-temperature environments.