Stijn Peter Kobussen
Research Subjects
Research Interests
Stijn Peter Kobussen has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Gijs Lukas Derks
DIFFER—Dutch Institute for Fundamental Energy Research, De Zaale 20, 5612 AJ Eindhoven, The Netherlands
5 shared publications - Kevin Verhaegh
Eindhoven University of Technology
4 shared publications - Sven Wiesen
DIFFER—Dutch Institute for Fundamental Energy Research, Eindhoven, The Netherlands
4 shared publications - Bob Kool
DIFFER—Dutch Institute for Fundamental Energy Research
3 shared publications - David Moulton
United Kingdom Atomic Energy Authority, Culham Centre for Fusion Energy, Culham Science Centre
3 shared publications - Egbert Westerhof
DIFFER—Dutch Institute for Fundamental Energy Research, De Zaale 20, 5612 AJ Eindhoven, Netherlands
3 shared publications
Latest Publications
- Open Access
- 4 November 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 67 (1) , 016027
System identification simulations using the advanced fluid neutral model and wide grid formalism in SOLPS-ITER
This work presents a first step towards using the SOLPS-ITER code package (Wiesen 2015 J. Nucl. Mater. 463 480–4) for synthetic system identification (SysID) using multisine perturbations. Numerical modelling is used to replicate SysID experiments performed to establish exhaust control done on MAST-U (Kool 2025 Nat. Energy 10 1116–31), (Van Berkel 2025 DPP 2025 (APS)). These experiments involve perturbing the gas injection rate and observing the Scrape-Off-Layer (SOL) response in the frequency domain. The model used is the Advanced Fluid Neutral (AFN) model of SOLPS-ITER (Horsten 2022 Nucl. Mater. Energy 33 101247), implemented in the Wide Grids version of the code (Dekeyser 2021 Nucl. Mater. Energy 27 100999). The grid was generated with the Grid Optimization and Adaptation Toolbox (Van den kerkhof 2024 Contrib. Plasma Phys. 64 e202300134) and extends to the vessel wall, to enable calculating fluid neutral parameters across the entire domain. New boundary condition types were implemented in the code to allow for multisine gas injection perturbations, as well as reservoir models for remote vessel regions without plasma. In steady state, it is possible to simulate plasmas ranging from attached to deeply detached using different gas injection rates. This allows for comparison between simulation and experimental results at similar levels of detachment. Comparison between simulation and experimental data in the frequency domain shows that the AFN SOLPS-ITER simulations predict faster response times to divertor fuelling perturbations than the experiments, likely in part due to the fluid approximation used for the neutrals. When including the reservoir models for remote vessel regions the phase shifts increase, but are still too low compared to experiments.
- 4 November 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 67 (1) , 016027
Open AccessSystem identification simulations using the advanced fluid neutral model and wide grid formalism in SOLPS-ITER
This work presents a first step towards using the SOLPS-ITER code package (Wiesen 2015 J. Nucl. Mater. 463 480–4) for synthetic system identification (SysID) using multisine perturbations. Numerical modelling is used to replicate SysID experiments performed to establish exhaust control done on MAST-U (Kool 2025 Nat. Energy 10 1116–31), (Van Berkel 2025 DPP 2025 (APS)). These experiments involve perturbing the gas injection rate and observing the Scrape-Off-Layer (SOL) response in the frequency domain. The model used is the Advanced Fluid Neutral (AFN) model of SOLPS-ITER (Horsten 2022 Nucl. Mater. Energy 33 101247), implemented in the Wide Grids version of the code (Dekeyser 2021 Nucl. Mater. Energy 27 100999). The grid was generated with the Grid Optimization and Adaptation Toolbox (Van den kerkhof 2024 Contrib. Plasma Phys. 64 e202300134) and extends to the vessel wall, to enable calculating fluid neutral parameters across the entire domain. New boundary condition types were implemented in the code to allow for multisine gas injection perturbations, as well as reservoir models for remote vessel regions without plasma. In steady state, it is possible to simulate plasmas ranging from attached to deeply detached using different gas injection rates. This allows for comparison between simulation and experimental results at similar levels of detachment. Comparison between simulation and experimental data in the frequency domain shows that the AFN SOLPS-ITER simulations predict faster response times to divertor fuelling perturbations than the experiments, likely in part due to the fluid approximation used for the neutrals. When including the reservoir models for remote vessel regions the phase shifts increase, but are still too low compared to experiments.
- 1 October 2026
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 68 (10) , 105010
Steady-state and dynamic validation of DIV1D with SOLPS-ITER and MAST-U experiments
Future fusion reactors will require real-time detachment control to maintain divertor heat and particle fluxes within material limits. Here, we assess the time-dependent 1D scrape-off-layer model DIV1D as a reduced-order plant model for detachment controller design by benchmarking its steady-state predictions and control-relevant dynamics for a MAST-U H-mode scenario, respectively, against SOLPS-ITER simulations and experimental data. After tuning a small set of free parameters, DIV1D reproduces the main quantities from 1D mapped SOLPS profiles. Density-ramp and molecular-puffing scans show that DIV1D captures the trends in key target quantities. Multi-sine system-identification simulations show that baseline DIV1D responds faster than MAST-U system-identification experiments (Kool et al 2025 Nat. Energy 10 1116–31). The agreement improves substantially when the total particle throughput is reduced to experimentally representative levels. This result demonstrates that the total particle throughput in the global particle balance is a key determinant of the modeled control-relevant dynamics and must be represented accurately for reliable plant-model behavior. These findings establish DIV1D as a useful tool for model-based detachment controller design on MAST-U, with direct relevance to next-step devices, where experimental system-identification opportunities will be limited and reduced-order models will be essential for pre-operational controller development.
- 1 October 2026
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 68 (10) , 105010
Steady-state and dynamic validation of DIV1D with SOLPS-ITER and MAST-U experiments
Future fusion reactors will require real-time detachment control to maintain divertor heat and particle fluxes within material limits. Here, we assess the time-dependent 1D scrape-off-layer model DIV1D as a reduced-order plant model for detachment controller design by benchmarking its steady-state predictions and control-relevant dynamics for a MAST-U H-mode scenario, respectively, against SOLPS-ITER simulations and experimental data. After tuning a small set of free parameters, DIV1D reproduces the main quantities from 1D mapped SOLPS profiles. Density-ramp and molecular-puffing scans show that DIV1D captures the trends in key target quantities. Multi-sine system-identification simulations show that baseline DIV1D responds faster than MAST-U system-identification experiments (Kool et al 2025 Nat. Energy 10 1116–31). The agreement improves substantially when the total particle throughput is reduced to experimentally representative levels. This result demonstrates that the total particle throughput in the global particle balance is a key determinant of the modeled control-relevant dynamics and must be represented accurately for reliable plant-model behavior. These findings establish DIV1D as a useful tool for model-based detachment controller design on MAST-U, with direct relevance to next-step devices, where experimental system-identification opportunities will be limited and reduced-order models will be essential for pre-operational controller development.
- Open Access
- 12 May 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (6) , 066010
A multi-model system-identification comparison with the global particle dynamics in TCV
In this work, we compare physics-based dynamic exhaust models with frequency response measurements (FRMs) of the global particle dynamics in the Tokamak à Configuration Variable (TCV). The aim is to understand and model the experimental in-vessel dynamic response of plasma and neutrals to deuterium gas puff modulations with three models of varying fidelity: a 0D three chamber model (TCM); DIV1D, which models the edge plasma in 1D, and SOLEDGE3X for 2D-axisymmetric modeling. We find that the dynamic behavior of the global particle balance as observed in TCV can be reproduced by SOLEDGE3X and with specific parameter settings also by TCM and DIV1D, for FRMs between 3 and 40 Hz. For TCM and DIV1D, the coupling to a core reservoir and a realistic time for neutrals to ionize are found important to align with measurements. We argue from this comparison that for dynamics driven by particle kinetics, it is almost impossible to investigate one domain irrespective of others and that one should formally consider the coupled nature of the particle dynamics over domains. In TCV, this means that one cannot ignore that over 60% of the neutral ionization takes place inside the core confined region, for the scenarios considered in this study. The presented dynamic model validation should be detailed much further and extended to other devices to better understand exhaust dynamics, providing the essential building blocks required to design exhaust control systems in future fusion reactors.
- 12 May 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (6) , 066010
Open AccessA multi-model system-identification comparison with the global particle dynamics in TCV
In this work, we compare physics-based dynamic exhaust models with frequency response measurements (FRMs) of the global particle dynamics in the Tokamak à Configuration Variable (TCV). The aim is to understand and model the experimental in-vessel dynamic response of plasma and neutrals to deuterium gas puff modulations with three models of varying fidelity: a 0D three chamber model (TCM); DIV1D, which models the edge plasma in 1D, and SOLEDGE3X for 2D-axisymmetric modeling. We find that the dynamic behavior of the global particle balance as observed in TCV can be reproduced by SOLEDGE3X and with specific parameter settings also by TCM and DIV1D, for FRMs between 3 and 40 Hz. For TCM and DIV1D, the coupling to a core reservoir and a realistic time for neutrals to ionize are found important to align with measurements. We argue from this comparison that for dynamics driven by particle kinetics, it is almost impossible to investigate one domain irrespective of others and that one should formally consider the coupled nature of the particle dynamics over domains. In TCV, this means that one cannot ignore that over 60% of the neutral ionization takes place inside the core confined region, for the scenarios considered in this study. The presented dynamic model validation should be detailed much further and extended to other devices to better understand exhaust dynamics, providing the essential building blocks required to design exhaust control systems in future fusion reactors.
- Open Access
- 6 January 2026
- Published by Elsevier in Fusion Engineering and Design
- Vol. 224
From MAST-U to STEP: Power exhaust control challenges and opportunities
- 6 January 2026
- Published by Elsevier in Fusion Engineering and Design
- Vol. 224
Open AccessFrom MAST-U to STEP: Power exhaust control challenges and opportunities
- Open Access
- 6 October 2025
- Published by IOP Publishing in Nuclear Fusion
- Vol. 65 (11) , 116010
A novel understanding of the role of plasma-molecular kinetics on divertor power exhaust
During detachment, a buffer of neutral atoms and molecules builds up between the target and the ionising plasma. Collisions between the plasma and the molecules play an important role in the detachment process. Studies of plasma-molecular kinetics indicate that the gas temperature increases during deepening detachment for a wide range of conditions on the MAST-U and TCV tokamaks. This is related to an increased D 2 lifetime during detachment, leading to more plasma-molecule collisions that raise the molecular temperature. Such collisions subsequently result in power and momentum losses from the divertor plasma during detachment. Using a simplified inference, these losses are estimated using the rotational temperature, neutral pressure and ionisation front position. Significant power losses (about 10% of P SOL ) and dominant momentum losses (majority of the upstream pressure) from plasma-molecule collisions are inferred experimentally in long-legged, strongly baffled, detached divertors (MAST-U Super-X divertor). These findings are consistent with SOLPS-ITER simulations (about 15% of P SOL , and 65% of upstream pressure). Simulations also suggest that 40%–50% of the power crossing the ionisation front is lost downstream. The vibrational distribution obtained is compared with a collisional-radiative model setup using the same rate data as SOLPS-ITER, indicating some qualitative agreements and disagreements, potentially highlighting model gaps with regard to the default rates used. These interpretations highlight the importance of plasma-molecular collisions, leading to power and momentum losses during detachment.
- 6 October 2025
- Published by IOP Publishing in Nuclear Fusion
- Vol. 65 (11) , 116010
Open AccessA novel understanding of the role of plasma-molecular kinetics on divertor power exhaust
During detachment, a buffer of neutral atoms and molecules builds up between the target and the ionising plasma. Collisions between the plasma and the molecules play an important role in the detachment process. Studies of plasma-molecular kinetics indicate that the gas temperature increases during deepening detachment for a wide range of conditions on the MAST-U and TCV tokamaks. This is related to an increased D 2 lifetime during detachment, leading to more plasma-molecule collisions that raise the molecular temperature. Such collisions subsequently result in power and momentum losses from the divertor plasma during detachment. Using a simplified inference, these losses are estimated using the rotational temperature, neutral pressure and ionisation front position. Significant power losses (about 10% of P SOL ) and dominant momentum losses (majority of the upstream pressure) from plasma-molecule collisions are inferred experimentally in long-legged, strongly baffled, detached divertors (MAST-U Super-X divertor). These findings are consistent with SOLPS-ITER simulations (about 15% of P SOL , and 65% of upstream pressure). Simulations also suggest that 40%–50% of the power crossing the ionisation front is lost downstream. The vibrational distribution obtained is compared with a collisional-radiative model setup using the same rate data as SOLPS-ITER, indicating some qualitative agreements and disagreements, potentially highlighting model gaps with regard to the default rates used. These interpretations highlight the importance of plasma-molecular collisions, leading to power and momentum losses during detachment.
- Open Access
- 30 September 2025
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 67 (10) , 105003
Benchmarking the global particle balance of DIV1D with SOLPS-ITER simulations on the tokamak à configuration variable
This paper investigates the global particle balance of DIV1D, a 1D scrape-off layer (SOL) model extended with reservoirs for neutrals outside the plasma and for the core particle content. The aim of DIV1D is to capture the global particle balance and SOL solutions as a function of gas puffing. To this end, DIV1D is calibrated on solutions of 1D mapped SOLPS-ITER simulations for a density ramp on the tokamak à configuration variable. In this density ramp (as a function of core ion fluxes and reservoir densities) DIV1D predictions for upstream plasma density, upstream electron temperature, target ion flux and target heat flux align mostly within confidence intervals of mapped 1D SOLPS-ITER solutions. For low upstream densities, the target temperature is overestimated by 2 to 4 eV. Simulating the global particle balance as a function of molecular puffing, DIV1D recovers upstream plasma densities and reservoir atomic densities while the core density sensitivity is overestimated by a factor six, whereas sensitivities of divertor reservoir molecular densities are underestimated by a factor three. Special attention is given to wall association effects outside the plasma and SOL opacity in achieving imperfect but acceptable agreement with mapped SOLPS-ITER solutions.
- 30 September 2025
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 67 (10) , 105003
Open AccessBenchmarking the global particle balance of DIV1D with SOLPS-ITER simulations on the tokamak à configuration variable
This paper investigates the global particle balance of DIV1D, a 1D scrape-off layer (SOL) model extended with reservoirs for neutrals outside the plasma and for the core particle content. The aim of DIV1D is to capture the global particle balance and SOL solutions as a function of gas puffing. To this end, DIV1D is calibrated on solutions of 1D mapped SOLPS-ITER simulations for a density ramp on the tokamak à configuration variable. In this density ramp (as a function of core ion fluxes and reservoir densities) DIV1D predictions for upstream plasma density, upstream electron temperature, target ion flux and target heat flux align mostly within confidence intervals of mapped 1D SOLPS-ITER solutions. For low upstream densities, the target temperature is overestimated by 2 to 4 eV. Simulating the global particle balance as a function of molecular puffing, DIV1D recovers upstream plasma densities and reservoir atomic densities while the core density sensitivity is overestimated by a factor six, whereas sensitivities of divertor reservoir molecular densities are underestimated by a factor three. Special attention is given to wall association effects outside the plasma and SOL opacity in achieving imperfect but acceptable agreement with mapped SOLPS-ITER solutions.
- Open Access
- 22 July 2025
- Published by IOP Publishing in Nuclear Fusion
- Vol. 65 (8) , 086027
On the role of atomic momentum and molecules in self-consistent 1D scrape-off layer simulation of MAST-U, using DIV1D
In this paper, the 1D physics-based dynamic scrape-off-layer (SOL) model DIV1D is extended to include molecular interactions and the effects of finite atomic flow velocity parallel to the magnetic field lines. The addition of molecular interactions, atomic flow, and geometric settings in DIV1D leads to qualitative agreement with stationary 1D profiles obtained by mapping 2D SOLPS-ITER simulations for the parallel heat flux, electron temperature, electron density, plasma flow velocity, atomic density, atomic flow velocity and molecular density. Steady-state simulations of DIV1D show higher levels of particle, momentum and heat losses through collisional-radiative interactions between ions and molecules, compared to ions and atoms, in the divertor. Density ramp simulations show that DIV1D is now capable of dynamically transitioning between different SOLPS-ITER equilibria for MAST-U, capturing behaviour throughout the target particle flux rollover into deeply detached regimes.
- 22 July 2025
- Published by IOP Publishing in Nuclear Fusion
- Vol. 65 (8) , 086027
Open AccessOn the role of atomic momentum and molecules in self-consistent 1D scrape-off layer simulation of MAST-U, using DIV1D
In this paper, the 1D physics-based dynamic scrape-off-layer (SOL) model DIV1D is extended to include molecular interactions and the effects of finite atomic flow velocity parallel to the magnetic field lines. The addition of molecular interactions, atomic flow, and geometric settings in DIV1D leads to qualitative agreement with stationary 1D profiles obtained by mapping 2D SOLPS-ITER simulations for the parallel heat flux, electron temperature, electron density, plasma flow velocity, atomic density, atomic flow velocity and molecular density. Steady-state simulations of DIV1D show higher levels of particle, momentum and heat losses through collisional-radiative interactions between ions and molecules, compared to ions and atoms, in the divertor. Density ramp simulations show that DIV1D is now capable of dynamically transitioning between different SOLPS-ITER equilibria for MAST-U, capturing behaviour throughout the target particle flux rollover into deeply detached regimes.