CCChih-Tsung Chang

Chih-Tsung Chang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Chih-Tsung Chang has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Analysis of Transition Mode Operation and Characteristic Curves in a Buck–Boost Converter for Unmanned Guided Vehicles

    by Kai-Jun Pai, Chih-Tsung Chang, Tzu-Chi Li

    This study presents the development of a buck–boost converter for application in unmanned guided vehicles (UGVs). The converter was designed with its input connected to a lithium iron phosphate battery pack and its output connected to an inverter. This configuration enabled the inverter, which powered the drive motor, to receive a stable DC voltage, thereby mitigating the effects of battery voltage fluctuations and enhancing the overall system stability. A pulse-width modulation (PWM) controller was employed to regulate the developed buck–boost converter. During the transition from buck mode to buck–boost mode, both power MOSFETs were simultaneously turned on; however, the datasheet of the PWM controller did not provide operational details or characteristic curve analysis for this mode. Therefore, this study derived the relationship between voltage gain and duty cycle ratio for the transition mode. To analyze the input voltage versus duty cycle characteristics, the linear equation was employed. This analytical model was adjusted to meet different converter specifications developed for experimental validation. Furthermore, the external-connect test capacitor method was used to extract the equivalent parasitic inductance and capacitance present in the practical circuit of the buck–boost converter. Based on these parameters, a snubber circuit was designed and connected across the drain–source terminals of the power MOSFETs to suppress voltage spikes occurring at the junctions. Finally, the developed buck–boost converter prototype was installed on an unmanned guided vehicle to convert the power from the lithium battery pack into the input power required by two inverters. A computer host was used to control the motor speed. By measuring the output voltage and current of the buck–boost converter, its electrical functionality and performance specifications were verified. The dimensions of the developed UGV chassis prototype were 40 cm in length, 45 cm in width, and 18.3 cm in height.

  • Open Access

    A Feasibility Study on Enhanced Mobility and Comfort: Wheelchairs Empowered by SSVEP BCI for Instant Noise Cancellation and Signal Processing in Assistive Technology

    by Chih-Tsung Chang, Kai-Jun Pai, Ming-An Chung, Chia-Wei Lin

    Steady-state visual evoked potential (SSVEP)-based brain–computer interface (BCI) technology offers a promising solution for wheelchair control by translating neural signals into navigation commands. A major challenge—signal noise caused by eye blinks—is addressed in this feasibility study through real-time blink detection and correction. The proposed design utilizes sensors to capture both SSVEP and blink signals, enabling the isolation and compensation of interference, which improves control accuracy by 14.68%. Real-time correction during blinks significantly enhances system reliability and responsiveness. Furthermore, user data and global positioning system (GPS) trajectories are uploaded to the cloud via Wi-Fi 6E for continuous safety monitoring. This approach not only restores mobility for users with physical disabilities but also promotes independence and spatial autonomy.


  • Open Access

    A Myoelectric Signal-Driven Intelligent Wheelchair System Incorporating Occlusal Control for Assistive Mobility

    by Chih-Tsung Chang, Yi-Chieh Hsu, Kai-Jun Pai, Chia-Yi Chou, Fu-Hua Xu

    This paper proposes a novel electric wheelchair that uses the surface electromyographic signal (sEMG) signals generated by the occlusal muscles to control the wheelchair during occlusion, instead of the traditional electric wheelchair that requires users to use their hands or feet for control. In this work, the myoelectric signal controls the electric wheelchair so that users with limited mobility and paraplegia can operate the electric wheelchair using the myoelectric signal generated during clenching. This is achieved through the seamless transmission of user data and GPS paths to the cloud and is facilitated by the state-of-the-art Wi-Fi 6E communication technology. By leveraging cloud connectivity, the system can instantly relay critical information, such as the user’s location and movement patterns, ensuring a prompt emergency response. Furthermore, several standard methods exist to set up the myoelectric signal electrodes and analyze the signals. This novel electric wheelchair can change the daily activities of many users who have difficulty walking. This work is presented as a proof-of-concept feasibility study rather than a comprehensive clinical validation.

  • Open Access

    Fuzzy-Aided P–PI Control for Start-Up Current Overshoot Mitigation in Solid-State Lithium Battery Chargers

    by Chih-Tsung Chang, Kai-Jun Pai

    A battery charger for solid-state lithium battery packs was developed and implemented. The power stage used a phase-shifted full-bridge converter integrated with a current-doubler rectifier and synchronous rectification. Dual voltage and current control loops were employed to enable constant-voltage and constant-current charging modes. To improve the lifespan of the output filter capacitor, the current-doubler rectifier was adopted to effectively reduce output current ripple. During the initial start-up phase, as the charger transitions from constant-voltage to constant-current output mode, the use of proportional–integral control in the voltage and current loop error amplifiers may cause current overshoot during the step-rising phase, primarily due to the integral action. Therefore, this study incorporated fuzzy control, proportional control, and proportional–integral control strategies into the current-loop error amplifier. This approach effectively reduced the current overshoot during the step-rising phase, preventing the charger from mistakenly triggering the overcurrent protection mode. The analysis and design considerations of the proposed circuit topology and control loop are presented. Experimental results agree with theoretical predictions, thereby confirming the validity of the proposed approach.