Mikkel Metzsch Juel
Mikkel Metzsch Juel has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Chenfanfu Jiang
University of California Los Angeles
2 shared publications - Hervé Vicari
WSL Institute for Snow and Avalanche Research SLF, Davos Dorf, Switzerland
2 shared publications - Johan Gaume
WSL Institute for Snow and Avalanche Research SLF, Davos Dorf, 7260, Switzerland
2 shared publications - Lars Blatny
Institute for Geotechnical Engineering, ETH Zurich, CH-8093 Zurich, Switzerland
2 shared publications - Yidong Zhao
Department of Civil and Environmental Engineering KAIST Daejeon South Korea
2 shared publications - Anders Malthe-Sørenssen
University of Oslo
1 shared publication
Latest Publications
- Open Access
- 25 June 2026
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 461
A stabilized fractional-step MPM with pressure gradient projection for coupled hydromechanical extreme deformations
- 25 June 2026
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 461
Open AccessA stabilized fractional-step MPM with pressure gradient projection for coupled hydromechanical extreme deformations
- Open Access
- 12 March 2026
- Published by Elsevier in SSRN Electronic Journal
A Stabilized Fractional-Step MPM with Pressure-Gradient Projection for Coupled Hydromechanical Extreme Deformations
We present a novel stabilized fractional-step two-phase double-point Material Point Method (MPM) for robust and computationally efficient simulations of extreme-deformation hydromechanical problems. Existing fractional-step models employ either a non-incremental pressure discretization, which is suitable for large deformations but inaccurate under low permeability conditions, or an incremental formulation that improves accuracy yet relies on stabilization methods that are currently inadequate for large deformations. To overcome these limitations, we present the first adaptation of the Stabilized Pressure by Gradient Projection (SPGP) method to the MPM framework and propose a Taylor Particle-in-Cell (TPIC) pressure mapping for improved free-surface treatment. A generalized temporal discretization for pressure and drag is developed, providing new insights into the numerical behavior of non-incremental and incremental fractional-step schemes. In particular, we demonstrate that the non‑incremental formulation remains inherently sensitive to permeability, whereas the incremental formulation achieves superior accuracy with permeability‑independent timesteps, eliminating the need for complex drag discretizations. The proposed method is implemented in the high-performance Taichi programming language, leveraging GPU acceleration and sparse grid capabilities, combined with a matrix-free conjugate gradient algorithm to efficiently solve the pressure–Poisson system. Our model is validated against a series of benchmark problems covering large deformations and phase separation phenomena, demonstrating high accuracy and robustness without case‑specific tuning of stabilization parameters. This advancement establishes a unified and robust foundation for simulating coupled hydromechanical processes, such as water-rich geophysical mass flows.
- 12 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA Stabilized Fractional-Step MPM with Pressure-Gradient Projection for Coupled Hydromechanical Extreme Deformations
We present a novel stabilized fractional-step two-phase double-point Material Point Method (MPM) for robust and computationally efficient simulations of extreme-deformation hydromechanical problems. Existing fractional-step models employ either a non-incremental pressure discretization, which is suitable for large deformations but inaccurate under low permeability conditions, or an incremental formulation that improves accuracy yet relies on stabilization methods that are currently inadequate for large deformations. To overcome these limitations, we present the first adaptation of the Stabilized Pressure by Gradient Projection (SPGP) method to the MPM framework and propose a Taylor Particle-in-Cell (TPIC) pressure mapping for improved free-surface treatment. A generalized temporal discretization for pressure and drag is developed, providing new insights into the numerical behavior of non-incremental and incremental fractional-step schemes. In particular, we demonstrate that the non‑incremental formulation remains inherently sensitive to permeability, whereas the incremental formulation achieves superior accuracy with permeability‑independent timesteps, eliminating the need for complex drag discretizations. The proposed method is implemented in the high-performance Taichi programming language, leveraging GPU acceleration and sparse grid capabilities, combined with a matrix-free conjugate gradient algorithm to efficiently solve the pressure–Poisson system. Our model is validated against a series of benchmark problems covering large deformations and phase separation phenomena, demonstrating high accuracy and robustness without case‑specific tuning of stabilization parameters. This advancement establishes a unified and robust foundation for simulating coupled hydromechanical processes, such as water-rich geophysical mass flows.
- Open Access
- 11 July 2025
- Published by National Academy of Sciences in Proceedings of the National Academy of Sciences
- Vol. 122 (28)
Strong strain dependence of friction in graphene kirigami allows engineering a negative coefficient of friction
The friction force typically increases linearly with normal load with a constant of proportionality called the coefficient of friction. Most materials exhibit a positive friction coefficient, so that an increase in the normal load leads to an increase in the friction force. Recently, materials with negative friction coefficients have been observed at meticulously constructed interfaces due to an interplay between superstructures at heterojunctions, out-of-plane buckling, or the ordering of thin water films. However, the magnitude of the negative friction coefficient is typically much less than 10 − 2 , the geometries are highly restrictive, and the mechanisms are difficult to scale to larger systems. Here, we show that a friction coefficient of − 0.08 can be obtained for a graphene sheet modified with kirigami-inspired cuts when inducing sheet tension through a normal load coupling. We use molecular dynamics simulations to show that the frictional behavior of kirigami cut sheets exhibits a strong nonmonotonic dependence on in-plane strain, while only weakly influenced by normal loading. We argue that the strong influence of strain arises from changes in commensurability between the graphene sheet and the substrate when the sheet deforms and buckles out of plane. We propose a simple nanomachine design that couples normal loading and sheet tension which enables the realization of different frictional laws, including a negative coefficient of friction. This represents a unique approach to creating tunable frictional surfaces and opens up applications in sheet-like systems across scales.
- 11 July 2025
- Published by National Academy of Sciences in Proceedings of the National Academy of Sciences
- Vol. 122 (28)
Open AccessStrong strain dependence of friction in graphene kirigami allows engineering a negative coefficient of friction
The friction force typically increases linearly with normal load with a constant of proportionality called the coefficient of friction. Most materials exhibit a positive friction coefficient, so that an increase in the normal load leads to an increase in the friction force. Recently, materials with negative friction coefficients have been observed at meticulously constructed interfaces due to an interplay between superstructures at heterojunctions, out-of-plane buckling, or the ordering of thin water films. However, the magnitude of the negative friction coefficient is typically much less than 10 − 2 , the geometries are highly restrictive, and the mechanisms are difficult to scale to larger systems. Here, we show that a friction coefficient of − 0.08 can be obtained for a graphene sheet modified with kirigami-inspired cuts when inducing sheet tension through a normal load coupling. We use molecular dynamics simulations to show that the frictional behavior of kirigami cut sheets exhibits a strong nonmonotonic dependence on in-plane strain, while only weakly influenced by normal loading. We argue that the strong influence of strain arises from changes in commensurability between the graphene sheet and the substrate when the sheet deforms and buckles out of plane. We propose a simple nanomachine design that couples normal loading and sheet tension which enables the realization of different frictional laws, including a negative coefficient of friction. This represents a unique approach to creating tunable frictional surfaces and opens up applications in sheet-like systems across scales.