Ao-Wei Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ao-Wei Liu has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Hai-Xing Wang
School of Astronautics, Beihang University, Beijing 100191, People’s Republic of China
4 shared publications Su-Rong Sun
School of Astronautics, Beihang University, Beijing 100191, People’s Republic of China
4 shared publications- Heji Huang
State Key Laboratory of High Temperature Gas Dynamics, Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, China
3 shared publications Jin-Yue Geng
Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, People’s Republic of China
2 shared publications- Qianhong Zhou
Institute of Applied Physics and Computational Mathematics
2 shared publications Shao-Xia Jia
Institute of Microelectronics, Chinese Academy of Science, Beijing 100029, People’s Republic of China
2 shared publications
Latest Publications
- 23 April 2026
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 35 (5)
Analysis of electron power absorption and loss mechanisms in the discharge chamber of air-breathing radio-frequency ion thruster
In recent years, very low Earth orbit (VLEO) has attracted growing interest for enabling higher-resolution Earth observation, shorter communication delays, and reduced launch costs. Air-breathing electric propulsion (ABEP), which employs upper atmospheric gas as propellant, has become a research hotspot. To investigate electron power absorption and loss mechanisms in an air-breathing radio-frequency (RF) ion thruster and improve ionization efficiency, a two-dimensional axisymmetric PIC-MCC simulation of the RIT-10 thruster was performed. Results show that increasing RF power enhances electron energy absorption and average energy. At low pressures, however, the reduced electron–neutral collision frequency relative to the coil frequency induces a large phase difference between the inductive field and electron current, leading to negative power absorption. Power loss analysis indicates that higher RF power increases losses through high-level excitation, ionization, and dissociation, while reducing low-level excitation. Comparisons between oxygen and nitrogen systems reveal that oxygen achieves superior ionization efficiency, with energy mainly lost via dissociation and ionization, whereas nitrogen predominantly loses energy through excitation. The ion beam consists mainly of N₂⁺ and O⁺. With increasing RF power, N₂⁺ production strengthens, raising its fraction from 32.82% to 37.25% while reducing O⁺ from 42.48% to 32.11%. Consequently, mass utilization and thrust efficiencies improve markedly, from 8.83% and 6.35% to 28.93% and 22.27%. These findings clarify key operational mechanisms of VLEO ABEP thrusters.
- 23 April 2026
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 35 (5)
Analysis of electron power absorption and loss mechanisms in the discharge chamber of air-breathing radio-frequency ion thruster
In recent years, very low Earth orbit (VLEO) has attracted growing interest for enabling higher-resolution Earth observation, shorter communication delays, and reduced launch costs. Air-breathing electric propulsion (ABEP), which employs upper atmospheric gas as propellant, has become a research hotspot. To investigate electron power absorption and loss mechanisms in an air-breathing radio-frequency (RF) ion thruster and improve ionization efficiency, a two-dimensional axisymmetric PIC-MCC simulation of the RIT-10 thruster was performed. Results show that increasing RF power enhances electron energy absorption and average energy. At low pressures, however, the reduced electron–neutral collision frequency relative to the coil frequency induces a large phase difference between the inductive field and electron current, leading to negative power absorption. Power loss analysis indicates that higher RF power increases losses through high-level excitation, ionization, and dissociation, while reducing low-level excitation. Comparisons between oxygen and nitrogen systems reveal that oxygen achieves superior ionization efficiency, with energy mainly lost via dissociation and ionization, whereas nitrogen predominantly loses energy through excitation. The ion beam consists mainly of N₂⁺ and O⁺. With increasing RF power, N₂⁺ production strengthens, raising its fraction from 32.82% to 37.25% while reducing O⁺ from 42.48% to 32.11%. Consequently, mass utilization and thrust efficiencies improve markedly, from 8.83% and 6.35% to 28.93% and 22.27%. These findings clarify key operational mechanisms of VLEO ABEP thrusters.
- 20 April 2026
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 35 (5)
Numerical simulation study on ionization and acceleration characteristics of low power iodine radio-frequency ion thruster
Iodine has a high atomic mass, low ionization threshold, abundant reserves, and low cost, making it a promising propellant for RF ion thrusters with significant development potential and application prospects. Two-dimensional axisymmetric PIC-MCC numerical simulation results for a low-power iodine RF ion thruster indicate that I + ions dominate the discharge with a large radial gradient, whereas I 2 + ions exhibit a lower but radially uniform concentration. Comparative analysis at RF power 35 W demonstrates that iodine achieves higher plasma density and beam current than xenon, which is attributed to the higher electron-neutral collision frequency of iodine, which mitigates electron inertia effects and weakens negative power absorption. Studies on the iodine thruster at different RF powers (screen grid voltage 1800 V) indicate that as power increases from 28 W to 47.5 W, the mass utilization efficiency and thrust efficiency improve from 36.13% and 24% to 58.49% and 29.6%, respectively, while power efficiency decreases slightly. Changing the grid voltage affects the state of the grid sheath layer. As the grid voltage increases from 1000 V to 1800 V (RF power 41.5 W), the sheath transitions from under-focused to over-focused, and the efficiencies of the thruster exhibit a linear increase trend.
- 20 April 2026
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 35 (5)
Numerical simulation study on ionization and acceleration characteristics of low power iodine radio-frequency ion thruster
Iodine has a high atomic mass, low ionization threshold, abundant reserves, and low cost, making it a promising propellant for RF ion thrusters with significant development potential and application prospects. Two-dimensional axisymmetric PIC-MCC numerical simulation results for a low-power iodine RF ion thruster indicate that I + ions dominate the discharge with a large radial gradient, whereas I 2 + ions exhibit a lower but radially uniform concentration. Comparative analysis at RF power 35 W demonstrates that iodine achieves higher plasma density and beam current than xenon, which is attributed to the higher electron-neutral collision frequency of iodine, which mitigates electron inertia effects and weakens negative power absorption. Studies on the iodine thruster at different RF powers (screen grid voltage 1800 V) indicate that as power increases from 28 W to 47.5 W, the mass utilization efficiency and thrust efficiency improve from 36.13% and 24% to 58.49% and 29.6%, respectively, while power efficiency decreases slightly. Changing the grid voltage affects the state of the grid sheath layer. As the grid voltage increases from 1000 V to 1800 V (RF power 41.5 W), the sheath transitions from under-focused to over-focused, and the efficiencies of the thruster exhibit a linear increase trend.
- 13 January 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (2) , 025217
Experimental study on the formation of triggered vacuum discharge anodic arc
The anodic arc of vacuum discharge can generate ion beams with relatively high density, which exhibits unique advantages and broad application prospects in the field of material processing. However, the generation of traditional anodic arcs is often constrained by conditions such as kA-level high current, sub-millimeter short gap, sub-millimeter anode size, and low-melting-point materials like aluminum. This study proposes an effective formation method for vacuum anodic arcs: by combining the pre-ionization effect of triggering with the discharge of the main circuit, an anodic arc for high-melting-point metals like titanium is realized. The results indicate that with triggering-induced pre-ionization, a reasonable combination of titanium anode parameters—including a main circuit breakdown voltage of 8–15 kV, an electrode gap of 4–10 mm, and an anode size of 1–3 mm—achieves a microsecond-level ( μ s) pulsed anodic arc. Under the same trigger current and anode size, the anodic arc intensity increases significantly with the increase in electrode gap; with the same electrode gap and anode size, it increases significantly as the trigger current decreases; and when the trigger current and electrode gap remain unchanged, it weakens rapidly with the increase in anode size. Studies on the influence of discharge and structural parameters on the anodic arc indicate that the power density deposited on the anode during the high-voltage discharge stage is the key parameter determining arc generation. Based on the experimental results, the order of magnitude of the power density required is estimated to be 10 10 W m −2 . This study can provide a reference for the design of vacuum anodic arcs devices.
- 13 January 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (2) , 025217
Experimental study on the formation of triggered vacuum discharge anodic arc
The anodic arc of vacuum discharge can generate ion beams with relatively high density, which exhibits unique advantages and broad application prospects in the field of material processing. However, the generation of traditional anodic arcs is often constrained by conditions such as kA-level high current, sub-millimeter short gap, sub-millimeter anode size, and low-melting-point materials like aluminum. This study proposes an effective formation method for vacuum anodic arcs: by combining the pre-ionization effect of triggering with the discharge of the main circuit, an anodic arc for high-melting-point metals like titanium is realized. The results indicate that with triggering-induced pre-ionization, a reasonable combination of titanium anode parameters—including a main circuit breakdown voltage of 8–15 kV, an electrode gap of 4–10 mm, and an anode size of 1–3 mm—achieves a microsecond-level ( μ s) pulsed anodic arc. Under the same trigger current and anode size, the anodic arc intensity increases significantly with the increase in electrode gap; with the same electrode gap and anode size, it increases significantly as the trigger current decreases; and when the trigger current and electrode gap remain unchanged, it weakens rapidly with the increase in anode size. Studies on the influence of discharge and structural parameters on the anodic arc indicate that the power density deposited on the anode during the high-voltage discharge stage is the key parameter determining arc generation. Based on the experimental results, the order of magnitude of the power density required is estimated to be 10 10 W m −2 . This study can provide a reference for the design of vacuum anodic arcs devices.
- 1 July 2025
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 34 (7) , 075007
Numerical simulation study on low-power xenon radio-frequency ion thruster
The optimization design and accurate performance prediction of a radio frequency ion thruster require coupled analysis of the discharge chamber and grided acceleration. In this numerical simulation study, the three-dimensional grid structure is reduced to an axisymmetric model through the equivalent transmittance method, enabling self-consistent simulation of the overall structure of the thruster. A particle-in-cell Monte Carlo collisions (PIC-MCC) method is implemented to investigate a 45 W xenon RF ion thruster operation, and obtain the spatial distributions of the magnetic field, the electric field, the potential, and the plasma parameters in the discharge chamber and the plume region. This approach conveniently correlates the upstream plasma generation process and downstream beam acceleration. Through combined theoretical analysis and numerical simulation, the electron energy absorption mechanism is elucidated, i.e. the RF coil generates the axial magnetic field through the current of a certain frequency, and further induces the azimuthal electric field, which causes the absorbed power to oscillate at a two-fold frequency due to the phase difference between the induced electric field and the current. The change of the absorbed energy of the electrons from the time-varying electromagnetic field causes the periodic change of the ionization rate and potential. Comparative analysis of the ion velocity and ion energy flux distribution before the screen grid and after the acceleration grid reveals that increasing RF power from 18 W to 45 W enhances discharge chamber plasma density while the degree of ionization at the grid exit rises from 15.37% to 32.83%. Concurrently, the grid sheath potential increases, improving the extracted ion beam occupancy ratio and focusing effect and ultimately enhances the thrust and specific impulse. The mass utilization and thrust efficiency of the thruster increase linearly with RF power.
- 1 July 2025
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 34 (7) , 075007
Numerical simulation study on low-power xenon radio-frequency ion thruster
The optimization design and accurate performance prediction of a radio frequency ion thruster require coupled analysis of the discharge chamber and grided acceleration. In this numerical simulation study, the three-dimensional grid structure is reduced to an axisymmetric model through the equivalent transmittance method, enabling self-consistent simulation of the overall structure of the thruster. A particle-in-cell Monte Carlo collisions (PIC-MCC) method is implemented to investigate a 45 W xenon RF ion thruster operation, and obtain the spatial distributions of the magnetic field, the electric field, the potential, and the plasma parameters in the discharge chamber and the plume region. This approach conveniently correlates the upstream plasma generation process and downstream beam acceleration. Through combined theoretical analysis and numerical simulation, the electron energy absorption mechanism is elucidated, i.e. the RF coil generates the axial magnetic field through the current of a certain frequency, and further induces the azimuthal electric field, which causes the absorbed power to oscillate at a two-fold frequency due to the phase difference between the induced electric field and the current. The change of the absorbed energy of the electrons from the time-varying electromagnetic field causes the periodic change of the ionization rate and potential. Comparative analysis of the ion velocity and ion energy flux distribution before the screen grid and after the acceleration grid reveals that increasing RF power from 18 W to 45 W enhances discharge chamber plasma density while the degree of ionization at the grid exit rises from 15.37% to 32.83%. Concurrently, the grid sheath potential increases, improving the extracted ion beam occupancy ratio and focusing effect and ultimately enhances the thrust and specific impulse. The mass utilization and thrust efficiency of the thruster increase linearly with RF power.