Avadhut Jadhav
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Avadhut Jadhav has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Gajendra Pol
Bharati Vidyapeeths College of Engineering
1 shared publication Pramod V Londhe
Department of Mechanical Engineering, Bharati Vidyapeeth (Deemed to be University) College of Engineering, Pune, MS, 411043, India
1 shared publication- Sujit Kumbhar
Department of Technology, Shivaji University, Kolhapur, India
1 shared publication - Udaysinh Bhapkar
Department of Mechanical Engineering, Kolhapur Institute of Technology’s College of Engineering (Empowered Autonomous), Kolhapur, India
1 shared publication
Latest Publications
- 1 May 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (10) , 105505
Performance and emission analysis of spark ignition engine powered by premium gasoline-ethanol blends with partial addition of amyl alcohol, iso-butanol and hydrogen
The depletion of fossil fuels is one of the major challenges in front of all countries. Many countries already blended ethanol up to 20% in gasoline. In the current experimental investigations, the performance and emission characteristics of spark ignition engine is analyzed fueled with partial addition amyl alcohol, isobutanol and hydrogen enrichment as compared to premium gasoline (PG). The PG-ethanol blends were prepared with partial addition of amyl alcohol, isobutanol (10% by vol.). The engine testing was carried out at constant engine speed (2500 rpm) and hydrogen enrichment. It was observed that there was improvement in BTE by 2.7% and 1.7% with partial addition of isobutonol and amyl alcohol respectively as compared to PG. The BTE of PG10H 2 (33.4%) were found to maximum among all tested fuel blends and was 3.6% greater than PG. When compared to PG, the inclusion of E and AA raises peak cylinder pressure and slightly advances the pressure rise, indicating enhanced combustion intensity and faster heat release. It was observed that PG emits the most CO at about 3.3 g kWh −1 , but blending with ethanol gradually reduces CO to around 3.2 g kWh −1 , 2.85 g kWh −1 , and 2.65 g/. There was reduction in CO emission by 3%, 13.6% and 19.6% with addition 20%, 40% and 60% of ethanol content as compared to PG. HC reduces to around 0.088 g kWh −1 (12% reduction) for PG20E, 0.075 g kWh −1 (25% reduction) for PG40E, and 0.060 g kWh −1 (40% reduction) for PG60E when ethanol is added. Blending with ethanol reduces NO x levels to around 8.6 g kWh −1 (≈3.4% reduction) for PG20E, 8.4 g kWh −1 (≈5.6%) for PG40E, and 8.2 g kWh −1 (≈7.9%) for PG60E. Amyl alcohol blends result in a significant drop, with PG10AA showing around 6.4 g kWh −1 (≈28% reduction), followed by 6.1 g kWh −1 (≈31% reduction), 5.9 g kWh −1 (≈34%), and 5.7 g kWh −1 (≈36%) for PG20E10AA, PG40E10AA, and PG60E10AA, respectively. Based on current investigations, PG20E blends showed comparative results to PG.
- 1 May 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (10) , 105505
Performance and emission analysis of spark ignition engine powered by premium gasoline-ethanol blends with partial addition of amyl alcohol, iso-butanol and hydrogen
The depletion of fossil fuels is one of the major challenges in front of all countries. Many countries already blended ethanol up to 20% in gasoline. In the current experimental investigations, the performance and emission characteristics of spark ignition engine is analyzed fueled with partial addition amyl alcohol, isobutanol and hydrogen enrichment as compared to premium gasoline (PG). The PG-ethanol blends were prepared with partial addition of amyl alcohol, isobutanol (10% by vol.). The engine testing was carried out at constant engine speed (2500 rpm) and hydrogen enrichment. It was observed that there was improvement in BTE by 2.7% and 1.7% with partial addition of isobutonol and amyl alcohol respectively as compared to PG. The BTE of PG10H 2 (33.4%) were found to maximum among all tested fuel blends and was 3.6% greater than PG. When compared to PG, the inclusion of E and AA raises peak cylinder pressure and slightly advances the pressure rise, indicating enhanced combustion intensity and faster heat release. It was observed that PG emits the most CO at about 3.3 g kWh −1 , but blending with ethanol gradually reduces CO to around 3.2 g kWh −1 , 2.85 g kWh −1 , and 2.65 g/. There was reduction in CO emission by 3%, 13.6% and 19.6% with addition 20%, 40% and 60% of ethanol content as compared to PG. HC reduces to around 0.088 g kWh −1 (12% reduction) for PG20E, 0.075 g kWh −1 (25% reduction) for PG40E, and 0.060 g kWh −1 (40% reduction) for PG60E when ethanol is added. Blending with ethanol reduces NO x levels to around 8.6 g kWh −1 (≈3.4% reduction) for PG20E, 8.4 g kWh −1 (≈5.6%) for PG40E, and 8.2 g kWh −1 (≈7.9%) for PG60E. Amyl alcohol blends result in a significant drop, with PG10AA showing around 6.4 g kWh −1 (≈28% reduction), followed by 6.1 g kWh −1 (≈31% reduction), 5.9 g kWh −1 (≈34%), and 5.7 g kWh −1 (≈36%) for PG20E10AA, PG40E10AA, and PG60E10AA, respectively. Based on current investigations, PG20E blends showed comparative results to PG.
- 23 July 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (3) , 032501
Optimizing heat sink efficiency: the role of coatings in modern thermal management systems
Efficient heat dissipation remains a core challenge in advanced cooling systems used in electronics, automotive, and industrial platforms. Heat sinks are widely employed to regulate temperatures; however, their efficiency is often hindered by material limitations, low thermal emissivity, surface degradation, and fouling effects. To address these challenges, various heat dissipation enhancement techniques have been explored, including geometric modifications, hybrid cooling methods, advanced materials, and surface treatments. Among these, heat sink coatings have emerged as a promising solution due to their ability to enhance emissivity, improve corrosion resistance, and maintain long-term thermal performance. This paper presents a detailed review of heat sink coatings, focusing on the properties, advantages, and limitations of different coating materials such as metallic, ceramic, polymeric, and nanostructured coatings. The study further investigates various deposition techniques, including electroplating, thermal spraying, chemical vapor deposition, physical vapor deposition, anodizing, and emerging nanocoating technologies, assessing their impact on coating thickness, thermal conductivity, adhesion strength, durability, and cost-effectiveness. Additionally, the review highlights recent advancements in nanostructured coatings, multifunctional surface treatments, and hybrid material coatings, which significantly improve thermal efficiency and operational stability. Despite notable progress, challenges such as cost constraints, process scalability, and long-term thermal stability persist, necessitating further research into low-cost, high-performance, and sustainable coating solutions. Future innovations integrating adaptive materials, AI-driven thermal optimization, and hybrid cooling techniques hold the potential to revolutionize next-generation heat sink technologies.
- 23 July 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (3) , 032501
Optimizing heat sink efficiency: the role of coatings in modern thermal management systems
Efficient heat dissipation remains a core challenge in advanced cooling systems used in electronics, automotive, and industrial platforms. Heat sinks are widely employed to regulate temperatures; however, their efficiency is often hindered by material limitations, low thermal emissivity, surface degradation, and fouling effects. To address these challenges, various heat dissipation enhancement techniques have been explored, including geometric modifications, hybrid cooling methods, advanced materials, and surface treatments. Among these, heat sink coatings have emerged as a promising solution due to their ability to enhance emissivity, improve corrosion resistance, and maintain long-term thermal performance. This paper presents a detailed review of heat sink coatings, focusing on the properties, advantages, and limitations of different coating materials such as metallic, ceramic, polymeric, and nanostructured coatings. The study further investigates various deposition techniques, including electroplating, thermal spraying, chemical vapor deposition, physical vapor deposition, anodizing, and emerging nanocoating technologies, assessing their impact on coating thickness, thermal conductivity, adhesion strength, durability, and cost-effectiveness. Additionally, the review highlights recent advancements in nanostructured coatings, multifunctional surface treatments, and hybrid material coatings, which significantly improve thermal efficiency and operational stability. Despite notable progress, challenges such as cost constraints, process scalability, and long-term thermal stability persist, necessitating further research into low-cost, high-performance, and sustainable coating solutions. Future innovations integrating adaptive materials, AI-driven thermal optimization, and hybrid cooling techniques hold the potential to revolutionize next-generation heat sink technologies.