GMGaurav Kumar Mishra

Gaurav Kumar Mishra

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Gaurav Kumar Mishra has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • RSM-Based Optimization and Validation of Maximum Power and Conversion Efficiency

    by Gaurav Kumar Mishra, Ashok Kumar Pandey, Om Hari Gupta

    1. The growing global demand for energy, together with the urgency to lower greenhouse gas emissions, has increased the adoption of renewable sources, particularly solar photovoltaic (PV) systems. ...

  • Efficient PWM-based motor control for educational robotic arm prototypes

    by Gaurav Kumar Mishra, Ashok Kumar Pandey, Om Hari Gupta

    Electrical motor control plays a vital role in robotics and automation, yet its hardware implementation often remain costly and challenging for students and researchers. Commercially available real-time simulators such as OPAL-RT or FPGA-based platforms are powerful but not affordable for common educational purposes. This paper proposes a low-cost and efficient hardware solution for motor control in a lightweight robotic arm prototype, using the Arduino Mega 2560 microcontroller as the central controller. This paper employs pulse-width modulation (PWM) through the Arduino IDE analogWrite() function to achieve precise speed, position, and direction control of multiple motors. The prototype integrates five motors on a single Arduino board: two 188 RPM DC encoder motors at the base and elbow joints, a 50 RPM precision DC motor, an SG90 servo motor, and a 28BYJ stepper motor. This paper proposes different low-cost driver circuits and sensors enable flexible control, including the L293D driver with a 4 × 4 keypad for DC motor actuation, the HC-SR04 ultrasonic sensor for servo positioning, and the ULN2003A driver with IR remote and rotary encoder for the stepper motor. A mathematical analysis of robotic arm kinematics is presented in this paper, which supports the placement of motors at appropriate joints for efficient operation. Experimental validation demonstrates that the proposed setup effectively controls motor speed, position, and direction in real time, providing an efficient and accessible alternative to costly simulators. This paper highlights the potential of low-cost microcontroller-based platforms as practical educational tools for visualizing and implementing motor control in robotic systems.


  • RSM-based experimental optimization and characterization of PV-battery systems

    by Gaurav Kumar Mishra, Ashok Kumar Pandey, Om Hari Gupta

    This paper presents an experimental and statistical study of a solar photovoltaic system integrated with a battery storage unit and direct current loads. A 45 W solar panel and a 12 V, 7.2 Ah lithium-ion battery were used for laboratory testing. Instead of an expensive pyranometer, solar irradiance was estimated using simple current measurements from a multimeter, offering a low-cost alternative validated through experiments with two different photovoltaic panels. This paper focuses on various parameters of measuring solar photovoltaic battery charging systems using minimal resources that can be easily affordable for micro-level solar photovoltaic users and researchers. Response surface methodology was employed using Design-Expert software to analyze the influence of irradiance, temperature, and load current on multiple responses: panel power, load power, system efficiency, maximum power, and power losses in the system. This paper also discusses the influence of short-circuit current and ambient temperature on solar irradiance in the main and check panels for comparative purposes. The model exhibited good agreement between experimental and predicted results (R2 = 0.982). Response surface plots revealed that irradiance and temperature were the most critical factors, while load current had a strong influence on system efficiency and power. This research demonstrates that combining experimental photovoltaic-battery testing with response surface methodology based optimization provides a practical pathway for improving system design and operation under real-world conditions.


  • Review of solar PV based transformerless multi-output hybrid converter

    by Gaurav Kumar Mishra, A K Pandey, O H Gupta

    There is an increase in interest in renewable sources of energy (RSE) due to their environment-friendly and never-ending approach to sources like solar energy, wind energy, etc. However, solar photovoltaic (PV) panels are more popular due to the widespread availability of solar energy worldwide. Hence, there is interest in the multiple-output hybrid converter, which will gain attention due to its ability to provide all available outputs from a single converter, known as a multi-output hybrid converter. This research paper proposes a literature review of direct current (DC) to direct current (DC) boost converters, direct current (DC) to alternating current (AC) inverters, and finally, multi-output hybrid converter (MOHC) topologies, which will offer boost direct current (DC) output, buck direct current output, 3-phase alternating current (AC) output, and 1-phase alternating current (AC) output from the solar-powered single direct current (DC) input, which is taken from solar photovoltaic panels and is referred a single-input multi-output (SIMO) converter. This paper focuses on various hybrid and multi-output converters, ultimately integrating all the ideas to achieve a multi-output hybrid converter. Multiple-output hybrid converters are gaining popularity in fields that require various DC and AC output voltages and loads. The different output voltages are found in various power electronics converters (PEC), such as buck converters, boost converters, 1-phase voltage source inverters (VSI), and 3-phase voltage source inverters (VSI), using direct current as input. However, the present scenario in the development of multiple output hybrid converters (MOHC) follows various aspects like reduced losses, increased power density, increased efficiency, reduced number of power electronics switches, reduced number of passive components, etc, which will be the current trends, especially to minimize the size and weight of the converter. This paper presents a detailed review of various topics related to multi-output and hybrid converters. In this paper, the focus is on transformerless converters because the transformer increases the weight and size of the converter. This paper serves as a basic reference for the multi-output hybrid converter (MOHC).