Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Shouqian Sheng has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental Study of Gas Thermodynamic Responses and Sealing Plug Deterioration Characteristics in Compressed Air Energy Storage Caverns

    by Yingsong Yang, Xiao Qu, Dawei Yin, Aibo Kou, Shouqian Sheng, Hongfa Ma

    During the frequent charging, discharging, and storage processes of underground compressed air energy storage systems, the damage and degradation of sealing plugs directly affect the long-term stability of gas storage caverns. Using a self-developed cyclic charging–storage–discharging–restorage gas disturbance rock testing system, this study conducted cyclic gas disturbance tests on sealing plug specimens at different storage pressures, followed by post-disturbance uniaxial compression tests, to investigate the thermodynamic response during cyclic disturbances and elucidate the mechanical property degradation mechanism of sealing plug specimens after cyclic disturbances. The results show that, during a single cycle, the gas temperature exhibits staged responses characterized by compression heating, cooling during high-pressure storage, decompression cooling, and temperature recovery during low-pressure storage. As the storage pressure increases, the heating rate increases from 0.005 to 0.016 °C/s, while the cooling rate increases from 0.023 to 0.055 °C/s. During cyclic charging–storage–discharging–restorage processes, the gas temperature exhibits an overall logarithmic growth trend comprising three stages, namely a rapid increase, a slow increase, and stabilization, with the degree of heat accumulation increasing progressively with storage pressure. Cyclic alternating loading by high-pressure gas aggravates internal specimen damage. With increasing storage pressure, the peak strength of the specimens after cyclic disturbances decreases by 8.14%, 8.99%, 11.58%, and 15.05%, respectively, while the elastic modulus decreases by 2.12%, 6.45%, 8.88%, and 13.49%, respectively. Acoustic emission activity during failure becomes more pronounced, and deformation localization intensifies. With increasing storage pressure, the macroscopic failure mode gradually changes from localized cracking to multiple-crack coalescence and block fragmentation, while the increase in average fracture-surface porosity rises from 7.29% to 37.89%. These results are important for assessing the stability of sealing plugs in underground CAES caverns.

  • Open Access

    Safety of Bed-Separation Grouting Filling Mining Under a Gas Station and Its Application

    by Tao Han, Shouqian Sheng, Dawei Yin, Faxin Li, Xiao Qu, Hongfa Ma, Ningqiang Zhu

    Bed-separation grouting filling mining is a damage-mitigation mining technology characterized by non-interfering mining and filling operations, low cost, and high efficiency. To recover coal resources from the 3801 working face located beneath a surface gas station in a Shanxi coal mine, this study first analyzed the maximum allowable deformation values for the gas station’s canopy, business hall, and oil storage tanks. Second, the feasibility and safety of bed-separation grouting filling mining at the 3801 working face were investigated using physical similarity modeling and the probability integral method. Finally, a field application of this technology was carried out at the 3801 working face. The results show that: (1) After the successive mining of the 3802, 3803 and 3801 working faces, the No. 17 bed separation was finally preserved above the 3801 working face. It is located in the upper part of the water-conducting fracture zone and has a thick impermeable isolation layer. (2) Physical similarity simulation and numerical simulation (3UDEC) of bed-separation grouting filling mining at the 3801 working face indicate that the underlying strata are effectively compacted after mining, and both overlying strata movement and surface subsidence above the grouting zone are significantly reduced. (3) The probability integral method was adopted to predict surface movement and deformation induced by mining at the 3801 working face (bed-separation grouting filling mining), the 3802 working face (fully mechanized top-coal caving mining) and the 3803 working face (full-seam mining in a single lift). All surface movement and deformation indices satisfy the surface deformation control requirements for the gas station. (4) After completion of the overburden bed-separation grouting filling project at the 3801 working face, the measured surface movement and deformation values during and after mining are all below the allowable deformation limits. No large deformations or cracks occurred in gas station structures including the canopy, business hall and oil tank farm. The protection effect is satisfactory, and the gas station has maintained normal operation throughout the mining period.

  • Open Access

    Experimental Study on Dynamic Mechanical Properties and Failure Characteristics of Dry and Saturated Granite Under Different Strain Rates

    by Yingsong Yang, Xiao Qu, Dawei Yin, Aibo Kou, Hongfa Ma, Shouqian Sheng, Faxin Li

    The stability of deep water-saturated rock masses under dynamic disturbance is crucial for the efficient development of deep geothermal resources. This study focuses on granite as the research object, using the Split Hopkinson Pressure Bar (SHPB) system to investigate the dynamic mechanical properties, energy dissipation, and failure characteristics of dry and saturated granite under impact loading, and to analyze the influence of water on the dynamic mechanical properties of granite. The results show that granite exhibits a Type II stress–strain curve (rebound phenomenon) at low strain rates, while at high strain rates, it exhibits a Type I stress–strain curve. The dynamic mechanical parameters of granite exhibit significant strain rate dependence, with water-saturated granite showing a stronger strain rate sensitivity. The dissipated energy and dissipation coefficient of the granite samples increase linearly and logarithmically, respectively, with the increase in incident energy. The dissipated energy of water-saturated granite is higher than that of dry granite. As the strain rate increases, the failure mode of the granite specimens transitions from splitting to fragmentation, with a more pronounced ductile fracture mode. The degree of fragmentation of water-saturated specimens is greater than that of dry specimens. As the strain rate increases, the difference in fractal dimensions between dry and water-saturated specimens decreases. At high strain rates, the free water within the rock generates inertial effects, meniscus effects, and viscous effects. When the strain rate reaches 124.22 s−1, the strength of the water-saturated specimen matches that of the dry specimen. The research findings provide theoretical support for the safe and efficient development of deep geothermal resources.


  • Open Access

    Study on the Synergistic Bearing Capacity Characteristics and Deformation and Damage Laws of Rock–Coal Combinations with Different Lithologies

    by Lei Han, Shouqian Sheng, Dawei Yin, Faxin Li, Fan Feng, Xiao Qu

    Ensuring the stability of underground structure engineering in deep coal mines is the key to the successful exploitation of deep geothermal resources in coal mines. Therefore, this paper carried out mechanical tests on rock–coal combinations under different rock properties and studied their stress–strain laws, energy and acoustic emission evolution laws, as well as deformation and failure laws. The main conclusions are as follows: (1) The strength of rock–coal assemblages mainly depends on the strength of coal samples far from the interface, and coal samples are the main bearing bodies in the process of uniaxial compression. (2) Because oil shale has a relatively low strength and large deformations, the rock property of relatively large deformations can improve the ability of the combinations to convert external energy into elastic energy. (3) The acoustic emission energy rate signals of rock–coal combinations can be divided into three stages: quiet, active, and sudden increase. The acoustic emission energy rate signals of limestone–coal and sandstone–coal assemblages are of the “lone-shock” type, while the acoustic emission energy rate signals of oil shale coal assemblages are of the “Multi-peak” type. (4) When oil shale with a relatively low strength and large deformations occurs, both the rock sample and coal sample of the combination appear to have deformation localization zones, and the deformation localization zones in the rock sample and coal sample run through the rock–coal interface, which eventually leads to the failure of both the rock sample and coal sample of the combination. These relevant research results help ensure the safe utilization of geothermal resources in deep coal mines and promote the global energy structure in accelerating the transformation to low-carbon and clean energy.


  • Open Access

    Properties of the self-expanding cement-based grouting material and its application

    by Shouqian Sheng, Dawei Yin, Xiao Qu, Hongfa Ma, Faxin Li, Xiushan Li


  • Open Access

    Experimental Research on the Performance of All-Solid-Waste Cementitious Grouting Filling Materials

    by Ningqiang Zhu, Dawei Yin, Xuelong Li, Shouqian Sheng

    Overburden bed separation grouting is a green mining method to control surface subsidence and protect surface buildings (structures). The performance of cementitious grouting material is the key factor affecting grouting filling. Although offering good fluidity and low cost, the fly ash (FA) slurry demands a significant water supply, undergoes high dehydration rates, and lacks cementing property. These factors result in low grouting efficiency and negatively impact the safety of operations in complex-structure areas. This work developed a CBF + D series all-solid-waste cementitious grouting filling material with blast furnace slag (BFS), FA, carbide slag (CS), desulfurization gypsum (DG), and calcium chloride (CaCl2) as components. Based on the orthogonal test, the basic performance test of the grouting material was carried out using macroscopic and microscopic test methods. The influences of the water–cement ratio, the mass ratio of BFS to FA, the proportion of CS, and the proportion of DG on the slurry density, fluidity, water extraction rate, and uniaxial compressive strength (UCS) of the stone body were assessed. The material’s hydration mechanism was analyzed by combining X-ray diffraction (XRD) and scanning electron microscopy (SEM) microscopic experiments. The optimal parameters for this test were as follows: a water–cement ratio of 0.7, a mass ratio of BFS to FA of 3:1, a proportion of CS of 40%, and a proportion of DG of 4%. Under the optimal conditions, the density of the slurry was 1.41 g·cm−3, with a fluidity of 15.7 cm, a water extraction rate of 0.107, and a UCS of the stone body of 6.25 MPa. The water extraction rate of the slurry is 67% lower than that of the FA slurry and the slurry has good cementation performance, while still maintaining its fluidity. This significantly enhanced the safety and applicability of the grouting filling process. In addition, CBF + D series all-solid-waste cementitious materials have solved the large accumulation of industrial wastes such as FA, BFS, and CS, which maximized the resource utilization rate of these wastes and brought significant economic benefits.