Pedro Seiti Endo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Pedro Seiti Endo has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Cleverson Bringhenti
Aeronautics Institute of Technology—ITA, São José dos Campos 12228-900, SP, Brazil
3 shared publications - Jesuino Takachi Tomita
Aeronautics Institute of Technology, São José dos Campos 12228-900, Brazil
3 shared publications - Franco Jefferds dos Santos Silva
Aeronautics Institute of Technology, São José dos Campos 12228-900, Brazil
2 shared publications - Ruben Bruno Diaz
Aeronautics Institute of Technology, São José dos Campos 12228-900, Brazil
2 shared publications
Latest Publications
- Open Access
- 24 June 2026
- Published by MDPI AG in Preprints.org
The Effects of Axial Slots with Radial Skew Angles on the Performance and Stall Margins in a Transonic Multi-Stage Axial Compressor
In the present study, three-dimensional steady-state Reynolds-Averaged Navier–Stokes (RANS) simulations were performed to investigate the influence of radial skew angle in axial slot casing treatments (CTs) applied to the first rotor of a transonic three-and-a-half-stage axial compressor. The investigation focuses on three skewed slot configurations with radial skew angles of 35°, 45°, and 60°, while the axially aligned slot configuration (0° skew angle), previously reported and validated, is adopted solely as a reference baseline. All configurations share identical geometric proportions, enabling the isolated assessment of skew-angle effects on compressor aerodynamic behavior. The results demonstrate that the radial skew angle significantly influences the balance between stall margin improvement and efficiency variation, with the magnitude of these effects strongly dependent on operating speed. Under off-design operating conditions, skewed axial slots provide substantial stall margin enhancement relative to the smooth casing configuration, with larger skew angles generally yielding greater improvements in compressor stability. Conversely, at the design speed, increasing skew angle is associated with a progressive efficiency penalty, highlighting the trade-off between aerodynamic stability enhancement and additional aerodynamic losses. Among the skewed configurations investigated, the 45° radial skew angle provides the most favorable compromise, delivering consistent stall margin improvement across the examined operating range while preserving compressor efficiency under nominal operating conditions. Overall, the present study demonstrates that radial skew angle constitutes a critical design parameter for axial slot casing treatments in multistage compressors and should therefore be carefully tailored to the intended operating regime. The findings extend the current understanding of axial-slot flow-control mechanisms and provide practical guidance for the aerodynamic design of casing treatments in transonic axial compressors.
- 24 June 2026
- Published by MDPI AG in Preprints.org
Open AccessThe Effects of Axial Slots with Radial Skew Angles on the Performance and Stall Margins in a Transonic Multi-Stage Axial Compressor
In the present study, three-dimensional steady-state Reynolds-Averaged Navier–Stokes (RANS) simulations were performed to investigate the influence of radial skew angle in axial slot casing treatments (CTs) applied to the first rotor of a transonic three-and-a-half-stage axial compressor. The investigation focuses on three skewed slot configurations with radial skew angles of 35°, 45°, and 60°, while the axially aligned slot configuration (0° skew angle), previously reported and validated, is adopted solely as a reference baseline. All configurations share identical geometric proportions, enabling the isolated assessment of skew-angle effects on compressor aerodynamic behavior. The results demonstrate that the radial skew angle significantly influences the balance between stall margin improvement and efficiency variation, with the magnitude of these effects strongly dependent on operating speed. Under off-design operating conditions, skewed axial slots provide substantial stall margin enhancement relative to the smooth casing configuration, with larger skew angles generally yielding greater improvements in compressor stability. Conversely, at the design speed, increasing skew angle is associated with a progressive efficiency penalty, highlighting the trade-off between aerodynamic stability enhancement and additional aerodynamic losses. Among the skewed configurations investigated, the 45° radial skew angle provides the most favorable compromise, delivering consistent stall margin improvement across the examined operating range while preserving compressor efficiency under nominal operating conditions. Overall, the present study demonstrates that radial skew angle constitutes a critical design parameter for axial slot casing treatments in multistage compressors and should therefore be carefully tailored to the intended operating regime. The findings extend the current understanding of axial-slot flow-control mechanisms and provide practical guidance for the aerodynamic design of casing treatments in transonic axial compressors.
- Open Access
Performance and Stall Margin Evaluation of Axial Slot Casing Treatment in a Transonic Multistage Compressor
Adverse pressure gradients are intrinsic to compressor flow behavior and are further intensified by secondary effects associated with rotor tip clearance flow interactions. Tip clearance generates leakage flow, which leads to the formation of tip leakage vortices, a major contributor to aerodynamic losses in axial compressors. These vortices significantly influence both compressor performance and operational stability. Extensive prior research has demonstrated that passive casing treatments, particularly axial slots, can substantially improve the stall margin in axial compressors. In this work, the performance of a new casing treatment geometry is investigated using the concept of recirculating flow within semi-circular axial slots. The proposed casing treatment geometry builds upon recent experimental findings involving single-rotor configurations. It was applied to the first rotor row of a three-and-a-half-stage (3.5-stage) axial compressor comprising an inlet guide vane followed by three rotor–stator stages. The numerical model incorporates axial slots with a novel periodic interface approach implemented in a multistage compressor simulation. Three-dimensional steady-state RANS (Reynolds Average Navier-Stokes) simulations were performed to investigate the aerodynamic effects of the casing treatment across various rotational speeds. The results for the casing treatment configuration were compared with those of a baseline smooth casing. The introduction of the new casing treatment produced noticeable modifications to the internal flow structure, particularly in the tip region, resulting in improved overall compressor stability within the operating range of 85 to 100% of design speed.
Open AccessPerformance and Stall Margin Evaluation of Axial Slot Casing Treatment in a Transonic Multistage Compressor
Adverse pressure gradients are intrinsic to compressor flow behavior and are further intensified by secondary effects associated with rotor tip clearance flow interactions. Tip clearance generates leakage flow, which leads to the formation of tip leakage vortices, a major contributor to aerodynamic losses in axial compressors. These vortices significantly influence both compressor performance and operational stability. Extensive prior research has demonstrated that passive casing treatments, particularly axial slots, can substantially improve the stall margin in axial compressors. In this work, the performance of a new casing treatment geometry is investigated using the concept of recirculating flow within semi-circular axial slots. The proposed casing treatment geometry builds upon recent experimental findings involving single-rotor configurations. It was applied to the first rotor row of a three-and-a-half-stage (3.5-stage) axial compressor comprising an inlet guide vane followed by three rotor–stator stages. The numerical model incorporates axial slots with a novel periodic interface approach implemented in a multistage compressor simulation. Three-dimensional steady-state RANS (Reynolds Average Navier-Stokes) simulations were performed to investigate the aerodynamic effects of the casing treatment across various rotational speeds. The results for the casing treatment configuration were compared with those of a baseline smooth casing. The introduction of the new casing treatment produced noticeable modifications to the internal flow structure, particularly in the tip region, resulting in improved overall compressor stability within the operating range of 85 to 100% of design speed.
- Open Access
- 4 August 2025
- Published by MDPI AG in Preprints.org
Performance and Stall Margin Evaluation of Axial Slot Casing Treatment in a Transonic Multistage Compressor
Adverse pressure gradients are intrinsic to the flow behavior in compressors and are further ex-acerbated by secondary effects arising from rotor tip clearance flow interactions, a phenomenon common across various turbomachinery configurations, axial and radial. Tip clearance induces leakage flow, which leads to the formation of tip leakage vortices—a principal contributor to aerodynamic losses in axial compressors. These vortices exert a significant impact on both com-pressor performance and the operational stability range. Extensive prior research has demon-strated that passive casing treatments, particularly the implementation of axial slots, can sub-stantially enhance stall margin in axial compressors. The recirculating flow established within semi-circular axial slots acts to mitigate the strength of the tip leakage vortex by redirecting low-momentum leakage flow upstream of the rotor leading edge, thereby introducing a resistance mechanism that suppresses flow leakage through the clearance gap. Many existing studies on axial slot implementation focus predominantly on high-performance single-stage axial compressors. Consequently, there remains a gap in the literature regarding the application and performance implications of such treatments in multi-stage compressor systems. In the present study, a passive casing treatment employing axial slots was integrated into a multi-stage axial compressor. The slot geometry was selected based on recent experimental findings involving single-rotor configura-tions. The casing treatment was applied over the first rotor row in a three-and-a-half-stage (3.5-stage) axial compressor configuration, comprising an inlet guide vane (IGV) followed by three rotor-stator stages. Three-dimensional steady-state numerical simulations were conducted to investigate the aerodynamic effects of the axial slot treatment across various rotational speeds. The results obtained for the slotted configuration were compared against a baseline case featuring a smooth casing. The introduction of axial slots induced noticeable modifications to the internal flow structure, particularly in the tip region, leading to an improvement in overall compressor stability within the operating range between 85% to 100% of design speed. Stall margins improved 3.55% at design speed. Significant stall margin improvement occurred at 95% design speed with ΔSM of 11.24%. At 85% design speed, the efficiency starts to deteriorate and axial slots did not improve the stall margins with ΔSM of -1.03 %.
- 4 August 2025
- Published by MDPI AG in Preprints.org
Open AccessPerformance and Stall Margin Evaluation of Axial Slot Casing Treatment in a Transonic Multistage Compressor
Adverse pressure gradients are intrinsic to the flow behavior in compressors and are further ex-acerbated by secondary effects arising from rotor tip clearance flow interactions, a phenomenon common across various turbomachinery configurations, axial and radial. Tip clearance induces leakage flow, which leads to the formation of tip leakage vortices—a principal contributor to aerodynamic losses in axial compressors. These vortices exert a significant impact on both com-pressor performance and the operational stability range. Extensive prior research has demon-strated that passive casing treatments, particularly the implementation of axial slots, can sub-stantially enhance stall margin in axial compressors. The recirculating flow established within semi-circular axial slots acts to mitigate the strength of the tip leakage vortex by redirecting low-momentum leakage flow upstream of the rotor leading edge, thereby introducing a resistance mechanism that suppresses flow leakage through the clearance gap. Many existing studies on axial slot implementation focus predominantly on high-performance single-stage axial compressors. Consequently, there remains a gap in the literature regarding the application and performance implications of such treatments in multi-stage compressor systems. In the present study, a passive casing treatment employing axial slots was integrated into a multi-stage axial compressor. The slot geometry was selected based on recent experimental findings involving single-rotor configura-tions. The casing treatment was applied over the first rotor row in a three-and-a-half-stage (3.5-stage) axial compressor configuration, comprising an inlet guide vane (IGV) followed by three rotor-stator stages. Three-dimensional steady-state numerical simulations were conducted to investigate the aerodynamic effects of the axial slot treatment across various rotational speeds. The results obtained for the slotted configuration were compared against a baseline case featuring a smooth casing. The introduction of axial slots induced noticeable modifications to the internal flow structure, particularly in the tip region, leading to an improvement in overall compressor stability within the operating range between 85% to 100% of design speed. Stall margins improved 3.55% at design speed. Significant stall margin improvement occurred at 95% design speed with ΔSM of 11.24%. At 85% design speed, the efficiency starts to deteriorate and axial slots did not improve the stall margins with ΔSM of -1.03 %.