Aristotel Issagulov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aristotel Issagulov has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Saule Sagintayeva
Department of Metallurgy and New Materials, Abylkas Saginov Karaganda Technical University, Karaganda 100000, Kazakhstan
4 shared publications - Yerbolat Makhambetov
Chemical-Metallurgical Institute Named After Zh. Abishev, Karaganda 100030, Kazakhstan
4 shared publications - Aibar Myrzagaliyev
Department of Metallurgy and New Materials, Abylkas Saginov Karaganda Technical University, Karaganda 100000, Kazakhstan
3 shared publications - Vitaliy Kulikov
Abylkas Saginov Karaganda Technical University
3 shared publications - D. A. Issagulova
Department of Metallurgy and New Materials, Abylkas Saginov Karaganda Technical University, Karaganda 100000, Kazakhstan
2 shared publications - Olga Zharkevich
Abylkas Saginov Karaganda Technical University
2 shared publications
Latest Publications
- Open Access
Influence of Process Parameters on Chromium Metallization During Chromite Pellet Pre-Reduction
The present study compares the effects of temperature, holding time, and nominal carbon excess on the pre-reduction of Donskoy chromite pellets with semi-coke. FactSage equilibrium calculations were interpreted alongside three laboratory series with different baselines. At 180 min with activated bentonite and 25% carbon excess, chromium metallization increased from 58.5% at 1350 °C to 87.0% at 1500 °C. At 1400 °C with attapulgite and 10% excess, extending holding time from 195 to 210 min increased chromium metallization from 70.6% to 82.8%, while residual carbon decreased from 4.96 to 4.00 wt.%. At 1500 °C and 180 min with activated bentonite, increasing excess from 15% to 25% increased chromium metallization from 68.9% to 87.0% and residual carbon from 2.30 to 4.74 wt.%. These condition-specific endpoints do not establish factor interactions, an optimum regime, or a kinetic mechanism. Unavailable uncertainty estimates limit quantitative interpretation. Equilibrium predictions and elemental maps do not independently verify the experimental phase sequence. Any industrial benefits, including chromium recovery, energy consumption, and continuous-process performance, require further validation.
Open AccessInfluence of Process Parameters on Chromium Metallization During Chromite Pellet Pre-Reduction
The present study compares the effects of temperature, holding time, and nominal carbon excess on the pre-reduction of Donskoy chromite pellets with semi-coke. FactSage equilibrium calculations were interpreted alongside three laboratory series with different baselines. At 180 min with activated bentonite and 25% carbon excess, chromium metallization increased from 58.5% at 1350 °C to 87.0% at 1500 °C. At 1400 °C with attapulgite and 10% excess, extending holding time from 195 to 210 min increased chromium metallization from 70.6% to 82.8%, while residual carbon decreased from 4.96 to 4.00 wt.%. At 1500 °C and 180 min with activated bentonite, increasing excess from 15% to 25% increased chromium metallization from 68.9% to 87.0% and residual carbon from 2.30 to 4.74 wt.%. These condition-specific endpoints do not establish factor interactions, an optimum regime, or a kinetic mechanism. Unavailable uncertainty estimates limit quantitative interpretation. Equilibrium predictions and elemental maps do not independently verify the experimental phase sequence. Any industrial benefits, including chromium recovery, energy consumption, and continuous-process performance, require further validation.
- Open Access
Aluminosilicochrome Produced from Technogenic Wastes as an Alternative to Conventional Ferrosilicochrome in Refined Ferrochrome Smelting
This study investigates the possibility of using aluminosilicochrome (ASC) produced from technogenic raw materials as a potential alternative to FSC-48 ferrosilicochrome in refined ferrochrome smelting. Laboratory smelting tests were carried out in an induction furnace using alumina crucibles with a charge mass of 50 g. The two variants were compared based on the material balance, SEM-EDS analysis of the metallic and slag phases, a conditional estimate of chromium transfer to the metal, and the results of thermodynamic modeling in FactSage 8.4. It was established that a Cr–Fe metallic phase is formed when both FSC-48 and ASC are used. The average metal mass was 13.8 g for FSC-48 and 13.3 g for ASC. According to SEM-EDS data, the Cr content in the metallic phase was 70.53 and 68.64 wt. %, respectively. Aluminum introduced with ASC predominantly transfers into the slag, increasing its Al content to 20.81 wt. %. The conditional estimate of total chromium transfer from the charge to the metallic phase was 91.9% for FSC-48 and 91.6% for ASC. FactSage modeling showed higher calculated ore-derived Cr recovery for ASC under equilibrium conditions; however, excessive ASC addition increased the Si content in the metal. The obtained results confirm the fundamental possibility of using ASC as a complex reductant in refined ferrochrome smelting.
Open AccessAluminosilicochrome Produced from Technogenic Wastes as an Alternative to Conventional Ferrosilicochrome in Refined Ferrochrome Smelting
This study investigates the possibility of using aluminosilicochrome (ASC) produced from technogenic raw materials as a potential alternative to FSC-48 ferrosilicochrome in refined ferrochrome smelting. Laboratory smelting tests were carried out in an induction furnace using alumina crucibles with a charge mass of 50 g. The two variants were compared based on the material balance, SEM-EDS analysis of the metallic and slag phases, a conditional estimate of chromium transfer to the metal, and the results of thermodynamic modeling in FactSage 8.4. It was established that a Cr–Fe metallic phase is formed when both FSC-48 and ASC are used. The average metal mass was 13.8 g for FSC-48 and 13.3 g for ASC. According to SEM-EDS data, the Cr content in the metallic phase was 70.53 and 68.64 wt. %, respectively. Aluminum introduced with ASC predominantly transfers into the slag, increasing its Al content to 20.81 wt. %. The conditional estimate of total chromium transfer from the charge to the metallic phase was 91.9% for FSC-48 and 91.6% for ASC. FactSage modeling showed higher calculated ore-derived Cr recovery for ASC under equilibrium conditions; however, excessive ASC addition increased the Si content in the metal. The obtained results confirm the fundamental possibility of using ASC as a complex reductant in refined ferrochrome smelting.
- Open Access
- 30 June 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (7) , 344
Study of the Structure and Properties of a Titanium Carbide-Based Composite Coating
The paper investigates the structure and properties of titanium carbide-based composite coatings produced by flame spraying. The relevance of the study is associated with the need to improve the wear resistance and mechanical properties of components operating under abrasive and impact loading conditions in the metallurgical and machine-building industries. A composite powder mixture consisting of titanium carbide, copper, and aluminum was used as the coating material. Titanium carbide acted as a strengthening phase, while copper and aluminum served as damping and binding components. The coating was deposited onto a 30KhGS steel substrate using a 6 PM-II Powder Flame Spray System. Sedimentation analysis, scanning electron microscopy, energy-dispersive analysis, microhardness measurements, and wear resistance tests were carried out. The results demonstrated that the powder mixture has a predominantly fine-dispersed structure favorable for coating formation. The obtained coating exhibited a heterogeneous composite structure with uniformly distributed titanium carbide particles within the metallic matrix. The microhardness of the coating reached HV 770. Wear resistance tests showed insignificant weight loss after 10,000–30,000 abrasion cycles, indicating high wear resistance of the developed coating. It was established that the proposed composite composition contributes to the improvement of the strength characteristics, microhardness, and tribological properties of the surface layer.
- 30 June 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (7) , 344
Open AccessStudy of the Structure and Properties of a Titanium Carbide-Based Composite Coating
The paper investigates the structure and properties of titanium carbide-based composite coatings produced by flame spraying. The relevance of the study is associated with the need to improve the wear resistance and mechanical properties of components operating under abrasive and impact loading conditions in the metallurgical and machine-building industries. A composite powder mixture consisting of titanium carbide, copper, and aluminum was used as the coating material. Titanium carbide acted as a strengthening phase, while copper and aluminum served as damping and binding components. The coating was deposited onto a 30KhGS steel substrate using a 6 PM-II Powder Flame Spray System. Sedimentation analysis, scanning electron microscopy, energy-dispersive analysis, microhardness measurements, and wear resistance tests were carried out. The results demonstrated that the powder mixture has a predominantly fine-dispersed structure favorable for coating formation. The obtained coating exhibited a heterogeneous composite structure with uniformly distributed titanium carbide particles within the metallic matrix. The microhardness of the coating reached HV 770. Wear resistance tests showed insignificant weight loss after 10,000–30,000 abrasion cycles, indicating high wear resistance of the developed coating. It was established that the proposed composite composition contributes to the improvement of the strength characteristics, microhardness, and tribological properties of the surface layer.
- Open Access
Thermodynamic Assessment and Process Development for Smelting Aluminosilicochrome from Technogenic Wastes of Ferroalloy and Coal Production
This study evaluated the production of aluminosilicochrome alloy (ASC) from technogenic wastes generated by ferroalloy and coal production. Chromite spinel dust from high-carbon ferrochrome gas cleaning, microsilica from ferrosilicon gas cleaning, and coal sludge as a reductant were used as raw materials. Thermodynamic modeling of the Fe–Cr–Si–Al–C–O system in HSC Chemistry 10 predicted that ASC formation is most favorable at 2000–2200 °C, where the metallic phase should contain (wt. %) 28.27–29.46 Cr, 35.21–36.06 Si, 10.14–11.89 Al, and 10.21–10.45 Fe. These predictions were tested by smelting a pre-agglomerated monocharge in a 100 kVA single-electrode electric arc furnace. The resulting alloy contained (wt. %) 24.23 Fe, 32.03 Si, 22.32 Cr, 18.70 Al, 0.36 C, 0.028 P, and 0.015 S. The experiments confirmed the formation of Si-, Cr-, and Al-rich ASC and demonstrated the feasibility of carbothermic production from these wastes. SEM-EDS revealed a multicomponent metallic matrix with pronounced microstructural heterogeneity and local redistribution of Fe, Si, Cr, and Al. Overall, the results support the use of fine technogenic wastes for producing a complex Fe–Cr–Si–Al alloy.
Open AccessThermodynamic Assessment and Process Development for Smelting Aluminosilicochrome from Technogenic Wastes of Ferroalloy and Coal Production
This study evaluated the production of aluminosilicochrome alloy (ASC) from technogenic wastes generated by ferroalloy and coal production. Chromite spinel dust from high-carbon ferrochrome gas cleaning, microsilica from ferrosilicon gas cleaning, and coal sludge as a reductant were used as raw materials. Thermodynamic modeling of the Fe–Cr–Si–Al–C–O system in HSC Chemistry 10 predicted that ASC formation is most favorable at 2000–2200 °C, where the metallic phase should contain (wt. %) 28.27–29.46 Cr, 35.21–36.06 Si, 10.14–11.89 Al, and 10.21–10.45 Fe. These predictions were tested by smelting a pre-agglomerated monocharge in a 100 kVA single-electrode electric arc furnace. The resulting alloy contained (wt. %) 24.23 Fe, 32.03 Si, 22.32 Cr, 18.70 Al, 0.36 C, 0.028 P, and 0.015 S. The experiments confirmed the formation of Si-, Cr-, and Al-rich ASC and demonstrated the feasibility of carbothermic production from these wastes. SEM-EDS revealed a multicomponent metallic matrix with pronounced microstructural heterogeneity and local redistribution of Fe, Si, Cr, and Al. Overall, the results support the use of fine technogenic wastes for producing a complex Fe–Cr–Si–Al alloy.
- Open Access
Ferrochrome Smelting Using Chrome Raw Materials Pre-Reduced with Various Reducing Agents
This study quantitatively evaluates the effect of solid-phase pre-reduction of chromite concentrate on the energy efficiency and techno-economic performance of high-carbon ferrochrome (HC FeCr) smelting. Laboratory pre-reduction experiments were conducted at 1200–1400 °C using Shubarkol coal, metallurgical coke, and special coke as carbonaceous reducing agents. Structural and phase transformations were characterized by X-ray diffraction (XRD) and scanning electron microscopy with energy-dispersive spectroscopy (SEM-EDS). At 1200 °C, the degree of metallization remained low (<5%), whereas at 1400 °C it increased to 41.3% under laboratory conditions and up to 65% in pilot-scale tests due to the decomposition of the spinel matrix and the formation of metallic and carbide phases. The application of pre-reduced feedstock in a submerged arc furnace reduced specific electricity consumption by up to 33.5% compared with conventional smelting and increased chromium recovery to 89.71%. Industrial-scale extrapolation indicates the potential to decrease power consumption to approximately 3190 kWh/t of alloy. Techno-economic analysis demonstrates that the use of pre-reduced feedstock reduces the production cost by approximately 10–23%, depending on the type of carbonaceous reducing agent (Shubarkol coal, metallurgical coke, or special coke). Special coke provided the highest energy efficiency, whereas Shubarkol coal ensured the greatest direct economic benefit. The integrated microstructural, energetic, and economic assessment confirms the industrial applicability of the proposed pre-reduction approach.
Open AccessFerrochrome Smelting Using Chrome Raw Materials Pre-Reduced with Various Reducing Agents
This study quantitatively evaluates the effect of solid-phase pre-reduction of chromite concentrate on the energy efficiency and techno-economic performance of high-carbon ferrochrome (HC FeCr) smelting. Laboratory pre-reduction experiments were conducted at 1200–1400 °C using Shubarkol coal, metallurgical coke, and special coke as carbonaceous reducing agents. Structural and phase transformations were characterized by X-ray diffraction (XRD) and scanning electron microscopy with energy-dispersive spectroscopy (SEM-EDS). At 1200 °C, the degree of metallization remained low (<5%), whereas at 1400 °C it increased to 41.3% under laboratory conditions and up to 65% in pilot-scale tests due to the decomposition of the spinel matrix and the formation of metallic and carbide phases. The application of pre-reduced feedstock in a submerged arc furnace reduced specific electricity consumption by up to 33.5% compared with conventional smelting and increased chromium recovery to 89.71%. Industrial-scale extrapolation indicates the potential to decrease power consumption to approximately 3190 kWh/t of alloy. Techno-economic analysis demonstrates that the use of pre-reduced feedstock reduces the production cost by approximately 10–23%, depending on the type of carbonaceous reducing agent (Shubarkol coal, metallurgical coke, or special coke). Special coke provided the highest energy efficiency, whereas Shubarkol coal ensured the greatest direct economic benefit. The integrated microstructural, energetic, and economic assessment confirms the industrial applicability of the proposed pre-reduction approach.
- Open Access
Modeling Wear of KNA-82 Coatings with 0.5% Yttrium for Radial Seals of Gas Turbine Engines
The paper presents the results of a study of linear wear of gas-flame and ion-plasma coatings of KNA-82 seals with an yttrium content of 0.5%, used in gas turbine engine assemblies, during physical modeling of their thermomechanical loading on small-sized samples. Tribotechnical tests were carried out in four stages, simulating the operating conditions of real gas turbine engines—from the first start-up with running-in of the coating cut-in areas to reaching a steady state with their service properties formed. The surface of the coatings was in contact with the ridges of triangular-shaped plates without heating (20 °C), at average heating (350–470 °C), after holding the samples at 1100 °C and average heating of 410–460 °C, and after grinding off the worn layer that had worn out after holding the samples at 1100 °C at average heating of 320–440 °C. Trends in the change in the linear ear of coatings and the formation of friction tracks caused by the uneven manifestation of the physical and mechanical properties of coatings, which are unevenly distributed throughout their body, were determined. It was found that both coatings tend to stabilize the wear process at certain mechanical pressures in the friction contact zone and only in the temperature range from 20 °C to 400 °C. These pressures range from 4 MPa to 6.7 MPa for gas-flame coatings and from 3 MPa to 4.2 MPa for ion-plasma coatings. It has been determined that within the depth range of 30–100 μm, the wear resistance (as assessed by linear wear) of ion-plasma coatings is higher than that of gas-flame coatings. This predetermines the fact that in the event of a catastrophic collision between the coatings and a blade, the geometry of the damage to the surface of the gas-flame coating will be greater than that of the ion-plasma coating. In the event of damage exceeding 75–100 μm in depth, both coatings become inoperable, since their wear characteristics are no longer maintained. This is indicated by a rapid decrease in their wear resistance under step loading. Moreover, the gas-flame coating is more prone to catastrophic failure than the ion-plasma coating.
Open AccessModeling Wear of KNA-82 Coatings with 0.5% Yttrium for Radial Seals of Gas Turbine Engines
The paper presents the results of a study of linear wear of gas-flame and ion-plasma coatings of KNA-82 seals with an yttrium content of 0.5%, used in gas turbine engine assemblies, during physical modeling of their thermomechanical loading on small-sized samples. Tribotechnical tests were carried out in four stages, simulating the operating conditions of real gas turbine engines—from the first start-up with running-in of the coating cut-in areas to reaching a steady state with their service properties formed. The surface of the coatings was in contact with the ridges of triangular-shaped plates without heating (20 °C), at average heating (350–470 °C), after holding the samples at 1100 °C and average heating of 410–460 °C, and after grinding off the worn layer that had worn out after holding the samples at 1100 °C at average heating of 320–440 °C. Trends in the change in the linear ear of coatings and the formation of friction tracks caused by the uneven manifestation of the physical and mechanical properties of coatings, which are unevenly distributed throughout their body, were determined. It was found that both coatings tend to stabilize the wear process at certain mechanical pressures in the friction contact zone and only in the temperature range from 20 °C to 400 °C. These pressures range from 4 MPa to 6.7 MPa for gas-flame coatings and from 3 MPa to 4.2 MPa for ion-plasma coatings. It has been determined that within the depth range of 30–100 μm, the wear resistance (as assessed by linear wear) of ion-plasma coatings is higher than that of gas-flame coatings. This predetermines the fact that in the event of a catastrophic collision between the coatings and a blade, the geometry of the damage to the surface of the gas-flame coating will be greater than that of the ion-plasma coating. In the event of damage exceeding 75–100 μm in depth, both coatings become inoperable, since their wear characteristics are no longer maintained. This is indicated by a rapid decrease in their wear resistance under step loading. Moreover, the gas-flame coating is more prone to catastrophic failure than the ion-plasma coating.
- Open Access
- 13 August 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (8) , 436
Development of a Molding Mixture for the Production of Large-Sized Casting Molds
This study presents the results of research on the use of Portland cement as a binder for producing semi-permanent molds intended for large-scale castings made from complex alloyed steels. Based on the conducted experiments, the optimal composition of a molding mixture based on Portland cement was determined to manufacture large molds with high operational performance. The technological properties of the mixtures were investigated, focusing on the flowability, sedimentation stability, and strength after curing. The recommended mixture composition is as follows: Portland cement—18.75%; sand—56.5%; quartz powder—25%; water—25%. To accelerate the hardening process, the use of curing accelerators is advised. The most effective additives are a 9% aluminum nitrate solution at 0.6–1.5% by weight or sodium aluminate at 3–4%. This composition ensures the required strength within a short curing time. A specific thermal treatment regime is also recommended to further stabilize the mold structure: heating to 450 °C at a rate of 75 °C per hour, holding for 2 h, followed by controlled cooling together with the furnace.
- 13 August 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (8) , 436
Open AccessDevelopment of a Molding Mixture for the Production of Large-Sized Casting Molds
This study presents the results of research on the use of Portland cement as a binder for producing semi-permanent molds intended for large-scale castings made from complex alloyed steels. Based on the conducted experiments, the optimal composition of a molding mixture based on Portland cement was determined to manufacture large molds with high operational performance. The technological properties of the mixtures were investigated, focusing on the flowability, sedimentation stability, and strength after curing. The recommended mixture composition is as follows: Portland cement—18.75%; sand—56.5%; quartz powder—25%; water—25%. To accelerate the hardening process, the use of curing accelerators is advised. The most effective additives are a 9% aluminum nitrate solution at 0.6–1.5% by weight or sodium aluminate at 3–4%. This composition ensures the required strength within a short curing time. A specific thermal treatment regime is also recommended to further stabilize the mold structure: heating to 450 °C at a rate of 75 °C per hour, holding for 2 h, followed by controlled cooling together with the furnace.