Showmik Ahsan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Showmik Ahsan has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Daniel Young
Department of Mechanical and Materials Engineering, Wright State University, Dayton, OH 45435, USA
5 shared publications - Sambhaji Kusekar
Department of Mechanical Engineering, Cleveland State University, Cleveland, OH 44115, USA
4 shared publications - Tushar Borkar
Department of Mechanical Engineering, Cleveland State University, Cleveland, OH 44115, USA
3 shared publications - Tushar Borkar
Department of Mechanical Engineering
3 shared publications - Aaron Adams
Department of Engineering Technology, Kennesaw State University, Marietta, GA 30060, USA
2 shared publications Bharat Gwalani
2 shared publications
Latest Publications
- Open Access
- 2 November 2026
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 18 (11)
Build orientation- and strain rate-dependent compressive response of SLS-printed glass-filled polyamide
Selective laser sintering (SLS) produces functional polymer components with complex geometries, yet the compressive behavior of printed parts across build orientations and strain rates remains sparsely documented. This study examines how build orientation and strain rate affect the compression response of glass bead-filled polyamide 12 (PA12-GF) printed on a Formlabs Fuse 1 using a fixed unidirectional scan strategy. Cylindrical specimens conforming to ASTM D695 (12.7 mm diameter, 25.4 mm length) were compressed to 50% engineering strain in seven build orientations ( X , Y , Z , D xy , D xz , D yz , D xyz ) at four strain rates (0.01, 1, 3, and 5 s −1 ). Compressive modulus and 0.2% offset yield stress were obtained from the stress-strain curves using adaptive toe compensation followed by ordinary least-squares regression. Microstructure was characterized by X-ray diffraction (XRD) for the crystalline phase, scanning electron microscopy (SEM) for bead morphology and interfacial bonding, density measurements using Archimedes and geometric methods. X-ray computed tomography (XRCT) was used to estimate the volumetric glass fraction. PA12-GF shows a clear stiffness-strength trade-off under compression, with the compressive modulus reaching 1.51 to 2.18 GPa while the yield stress remains within 41.0 to 61.7 MPa across all orientations and strain rates. SEM observations suggest that early yielding is associated with stress concentrations at the bead–matrix interface, as evidenced by debonding gaps and bead pullout craters on the fracture surface. The presence of glass beads alters the orientation response by providing additional load-transfer pathways across hatch boundaries, while interlayer interfaces remain the weaker load path in the build direction. Over the tested range, the modulus of elasticity increases with strain rate in all orientations, whereas the yield stress peaks near 3 s −1 before declining at 5 s −1 in most orientations. This behavior is consistent with local thermal softening from plastic-work heating, although other rate-dependent mechanisms may also contribute to the observed softening, including bead-matrix debonding. These results provide an orientation- and strain-rate-dependent compressive dataset and a microstructure-based framework for understanding the mechanical response of SLS-printed PA12-GF components.
- 2 November 2026
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 18 (11)
Open AccessBuild orientation- and strain rate-dependent compressive response of SLS-printed glass-filled polyamide
Selective laser sintering (SLS) produces functional polymer components with complex geometries, yet the compressive behavior of printed parts across build orientations and strain rates remains sparsely documented. This study examines how build orientation and strain rate affect the compression response of glass bead-filled polyamide 12 (PA12-GF) printed on a Formlabs Fuse 1 using a fixed unidirectional scan strategy. Cylindrical specimens conforming to ASTM D695 (12.7 mm diameter, 25.4 mm length) were compressed to 50% engineering strain in seven build orientations ( X , Y , Z , D xy , D xz , D yz , D xyz ) at four strain rates (0.01, 1, 3, and 5 s −1 ). Compressive modulus and 0.2% offset yield stress were obtained from the stress-strain curves using adaptive toe compensation followed by ordinary least-squares regression. Microstructure was characterized by X-ray diffraction (XRD) for the crystalline phase, scanning electron microscopy (SEM) for bead morphology and interfacial bonding, density measurements using Archimedes and geometric methods. X-ray computed tomography (XRCT) was used to estimate the volumetric glass fraction. PA12-GF shows a clear stiffness-strength trade-off under compression, with the compressive modulus reaching 1.51 to 2.18 GPa while the yield stress remains within 41.0 to 61.7 MPa across all orientations and strain rates. SEM observations suggest that early yielding is associated with stress concentrations at the bead–matrix interface, as evidenced by debonding gaps and bead pullout craters on the fracture surface. The presence of glass beads alters the orientation response by providing additional load-transfer pathways across hatch boundaries, while interlayer interfaces remain the weaker load path in the build direction. Over the tested range, the modulus of elasticity increases with strain rate in all orientations, whereas the yield stress peaks near 3 s −1 before declining at 5 s −1 in most orientations. This behavior is consistent with local thermal softening from plastic-work heating, although other rate-dependent mechanisms may also contribute to the observed softening, including bead-matrix debonding. These results provide an orientation- and strain-rate-dependent compressive dataset and a microstructure-based framework for understanding the mechanical response of SLS-printed PA12-GF components.
- Open Access
Microstructural, Mechanical and Corrosion Performance of NbZr1-Ti64 Multi-Material Structure Fabricated via Wire Arc Directed Deposition
This study investigates the fabricability, microstructures, and mechanical and corrosion behavior of a multi-material structure (MMS) composed of niobium alloy (NbZr1) and titanium alloy (Ti64) using a wire arc directed energy deposition process. The microstructure of NbZr1 alloy primarily consisted of equiaxed grains oriented in the rolling direction, while the deposited Ti64 microstructure exhibited ‘banding’ morphology and a basket-weave structure composed of α phase lamellae in a β matrix. The MMS interface revealed good metallurgical bonding and was free from defects such as cracks, pores and intermetallic phases. Niobium diffusion from NbZr1 into the Ti64 alloy resulted in the formation (β-Ti + Nb) of a solid solution which imparted strength to the MMS. Hardness testing showed that microhardness values follow the following trend: NbZr1 substrate > MMS interface > Ti64 deposit. The NbZr1–Ti64 multi-material structure developed in this study exhibited a balanced combination of ductility (22.73% elongation) and moderate tensile strength (254.18 MPa), outperforming most reported NbZr1-Ti64 MMS studies. All tensile specimens failed in a ductile manner on the NbZr1 side. The MMS demonstrated superior corrosion resistance, exhibiting the lowest corrosion current density and corrosion rate compared to its individual counterparts.
Open AccessMicrostructural, Mechanical and Corrosion Performance of NbZr1-Ti64 Multi-Material Structure Fabricated via Wire Arc Directed Deposition
This study investigates the fabricability, microstructures, and mechanical and corrosion behavior of a multi-material structure (MMS) composed of niobium alloy (NbZr1) and titanium alloy (Ti64) using a wire arc directed energy deposition process. The microstructure of NbZr1 alloy primarily consisted of equiaxed grains oriented in the rolling direction, while the deposited Ti64 microstructure exhibited ‘banding’ morphology and a basket-weave structure composed of α phase lamellae in a β matrix. The MMS interface revealed good metallurgical bonding and was free from defects such as cracks, pores and intermetallic phases. Niobium diffusion from NbZr1 into the Ti64 alloy resulted in the formation (β-Ti + Nb) of a solid solution which imparted strength to the MMS. Hardness testing showed that microhardness values follow the following trend: NbZr1 substrate > MMS interface > Ti64 deposit. The NbZr1–Ti64 multi-material structure developed in this study exhibited a balanced combination of ductility (22.73% elongation) and moderate tensile strength (254.18 MPa), outperforming most reported NbZr1-Ti64 MMS studies. All tensile specimens failed in a ductile manner on the NbZr1 side. The MMS demonstrated superior corrosion resistance, exhibiting the lowest corrosion current density and corrosion rate compared to its individual counterparts.
- Open Access
- 14 August 2026
- Published by MDPI AG in Preprints.org
Microstructural, Mechanical and Corrosion Performance of NbZr1-Ti64 Multi-Material Structure Fabricated via Wire Arc Directed Deposition
This study investigates the fabricability, microstructures, mechanical and corrosion behavior of multi-material structure (MMS) composed of niobium alloy (NbZr1) and titanium alloy (Ti64) using a wire-arc directed energy deposition process. The microstructure of NbZr1 alloy primarily consisted of equiaxed grains oriented in the rolling direction, while the deposited Ti64 microstructure exhibited ‘banding’ morphology and a basket weave structure composed of α phase lamellae in a β matrix. The MMS interface revealed good metallurgical bonding and was free from defects such as cracks, pores and intermetallic phases. Niobium diffusion from the NbZr1 into the Ti64 alloy resulted in formation (β-Ti + Nb) solid solution which imparted strength to the MMS. The hardness testing showed that microhardness values follow the trend: NbZr1 substrate > MMS interface > Ti64 deposit. The NbZr1–Ti64 multi-material structure developed in this study exhibited a balanced combination of ductility (22.73% elongation) and moderate tensile strength (254.18 MPa), outperforming most reported NbZr1-Ti64 MMS studies. All tensile specimens failed in ductile manner on NbZr1 side. The MMS demonstrated superior corrosion resistance, exhibiting the lowest corrosion current density and corrosion rate compared to its individual counterparts.
- 14 August 2026
- Published by MDPI AG in Preprints.org
Open AccessMicrostructural, Mechanical and Corrosion Performance of NbZr1-Ti64 Multi-Material Structure Fabricated via Wire Arc Directed Deposition
This study investigates the fabricability, microstructures, mechanical and corrosion behavior of multi-material structure (MMS) composed of niobium alloy (NbZr1) and titanium alloy (Ti64) using a wire-arc directed energy deposition process. The microstructure of NbZr1 alloy primarily consisted of equiaxed grains oriented in the rolling direction, while the deposited Ti64 microstructure exhibited ‘banding’ morphology and a basket weave structure composed of α phase lamellae in a β matrix. The MMS interface revealed good metallurgical bonding and was free from defects such as cracks, pores and intermetallic phases. Niobium diffusion from the NbZr1 into the Ti64 alloy resulted in formation (β-Ti + Nb) solid solution which imparted strength to the MMS. The hardness testing showed that microhardness values follow the trend: NbZr1 substrate > MMS interface > Ti64 deposit. The NbZr1–Ti64 multi-material structure developed in this study exhibited a balanced combination of ductility (22.73% elongation) and moderate tensile strength (254.18 MPa), outperforming most reported NbZr1-Ti64 MMS studies. All tensile specimens failed in ductile manner on NbZr1 side. The MMS demonstrated superior corrosion resistance, exhibiting the lowest corrosion current density and corrosion rate compared to its individual counterparts.
- Open Access
- 16 May 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 968
Investigating microstructural and mechanical property uniformity in 316L stainless steel alloys processed via laser powder bed fusion process
- 16 May 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 968
Open AccessInvestigating microstructural and mechanical property uniformity in 316L stainless steel alloys processed via laser powder bed fusion process
- Open Access
- 23 December 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 40, 1364-1380
Microstructural evolution and high-temperature deformation behavior of wire arc additively manufactured Inconel 718 forging Preforms: Toward a hybrid Additive–Forging Process
- 23 December 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 40, 1364-1380
Open AccessMicrostructural evolution and high-temperature deformation behavior of wire arc additively manufactured Inconel 718 forging Preforms: Toward a hybrid Additive–Forging Process
- Open Access
- 8 November 2025
- Published by Elsevier in Materials & Design
- Vol. 260
Microstructure Evolution, mechanical Properties, and biological Response of Ti-Nb-Zr-Ta (TNZT)/hBN metal matrix composites processed via spark plasma sintering (SPS)
- 8 November 2025
- Published by Elsevier in Materials & Design
- Vol. 260
Open AccessMicrostructure Evolution, mechanical Properties, and biological Response of Ti-Nb-Zr-Ta (TNZT)/hBN metal matrix composites processed via spark plasma sintering (SPS)
- Open Access
Laser Powder Bed Fusion and Hot Forging of 316L Stainless Steel: A Hybrid Additive Manufacturing Approach for Enhanced Performance
Forging plays a crucial role in various industries, including aerospace, automotive, oil and gas, and defense. We investigated the effect of post-processing forging on microstructural and mechanical properties of 316L stainless steel forging preforms fabricated by laser powder bed fusion. The as-built samples were subjected to hot forging in order to refine the microstructure and enhance mechanical performance. Detailed characterization was performed using Electron Backscatter Diffraction, Scanning Electron Microscopy, Energy Dispersive Spectroscopy, Tensile testing, and Hardness Testing. Substantial grain refinement (up to 97%) was observed, in addition to a reduction in porosity. The forging process effectively transformed the columnar grain morphology into equiaxed grains, increased yield and ultimate tensile strengths of 560 MPa and 740 MPa, representing 27% and 32% improvements, respectively, with a corresponding decrease in elongation to 32% from 47%. The horizontally built samples achieved the highest yield strength of 605 MPa but slightly lower UTS 710 MPa, representing 32% and 5% increment and decrease in ductility to 28% from 37.5%. These trends reflect the combined effects of work hardening and grain refinement, which enhance strength at the expense of ductility.
Open AccessLaser Powder Bed Fusion and Hot Forging of 316L Stainless Steel: A Hybrid Additive Manufacturing Approach for Enhanced Performance
Forging plays a crucial role in various industries, including aerospace, automotive, oil and gas, and defense. We investigated the effect of post-processing forging on microstructural and mechanical properties of 316L stainless steel forging preforms fabricated by laser powder bed fusion. The as-built samples were subjected to hot forging in order to refine the microstructure and enhance mechanical performance. Detailed characterization was performed using Electron Backscatter Diffraction, Scanning Electron Microscopy, Energy Dispersive Spectroscopy, Tensile testing, and Hardness Testing. Substantial grain refinement (up to 97%) was observed, in addition to a reduction in porosity. The forging process effectively transformed the columnar grain morphology into equiaxed grains, increased yield and ultimate tensile strengths of 560 MPa and 740 MPa, representing 27% and 32% improvements, respectively, with a corresponding decrease in elongation to 32% from 47%. The horizontally built samples achieved the highest yield strength of 605 MPa but slightly lower UTS 710 MPa, representing 32% and 5% increment and decrease in ductility to 28% from 37.5%. These trends reflect the combined effects of work hardening and grain refinement, which enhance strength at the expense of ductility.
- Open Access
- 27 August 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 38, 4939-4952
Microstructure and mechanical properties of Inconel-GNP reinforced composites: A parametric study on ball milling and spark plasma sintering
- 27 August 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 38, 4939-4952
Open AccessMicrostructure and mechanical properties of Inconel-GNP reinforced composites: A parametric study on ball milling and spark plasma sintering