Huidong Qu
Research Subjects
Huidong Qu has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Liping He
CCCC Fourth Harbor Engineering Co., Ltd., No. 368 Lijiao Road, Haizhu District, Guangzhou 510290, China
2 shared publications - Zhenghong Tian
Hohai University
2 shared publications - Changyue Luo
College of Water Conservancy and Hydropower Engineering, Hohai University, Nanjing 210098, China
1 shared publication - Fazhang Li
CCCC Fourth Harbor Engineering Co., Ltd., No. 368 Lijiao Road, Haizhu District, Guangzhou 510290, China
1 shared publication - Linjiang Yu
CCCC Fourth Harbor Engineering Co., Ltd., No. 368 Lijiao Road, Haizhu District, Guangzhou 510290, China
1 shared publication - Weihao Shen
College of Water Conservancy and Hydropower Engineering, Hohai University, Nanjing 210098, China
1 shared publication
Latest Publications
- Open Access
Study on Vibration Compaction Behavior of Fresh Concrete Mixture with Ternary Aggregate Grading
The vibration compaction behavior of fully graded fresh concrete differs fundamentally from that of conventional two-graded concrete. Based on measured vibration responses of an internal vibrator and sinking-ball tests, an energy transfer model for fully graded concrete was established by incorporating the effects of aggregate-specific surface area, paste–aggregate ratio, dynamic damping, and natural frequency, and the spatiotemporal attenuation of vibration energy in fresh concrete was systematically analyzed. Experimental results indicate that fully graded concrete exhibits a higher energy absorption capacity during the early stage of vibration, with a maximum energy absorption rate of 423 W and a peak energy transfer efficiency of 76.3%, both of which are significantly higher than those of two-graded concrete at the same slump. However, as a dense aggregate skeleton rapidly forms, the energy absorption efficiency of fully graded concrete decreases more rapidly during the middle and later stages of vibration, showing a characteristic pattern of “high initial absorption followed by rapid attenuation.” Through segregation assessment and porosity analysis, a safe vibration energy range for fully graded concrete was quantitatively determined, with lower and upper energy thresholds of 159.7 J·kg−1 and 538.5 J·kg−1, respectively. In addition, the experiments identified recommended vibration durations of 30–65 s and effective vibration influence radii of 22–85 mm for fully graded concrete under different slump conditions. These findings provide a quantitative basis for the control of vibration parameters and energy-oriented construction of fully graded concrete.
Open AccessStudy on Vibration Compaction Behavior of Fresh Concrete Mixture with Ternary Aggregate Grading
The vibration compaction behavior of fully graded fresh concrete differs fundamentally from that of conventional two-graded concrete. Based on measured vibration responses of an internal vibrator and sinking-ball tests, an energy transfer model for fully graded concrete was established by incorporating the effects of aggregate-specific surface area, paste–aggregate ratio, dynamic damping, and natural frequency, and the spatiotemporal attenuation of vibration energy in fresh concrete was systematically analyzed. Experimental results indicate that fully graded concrete exhibits a higher energy absorption capacity during the early stage of vibration, with a maximum energy absorption rate of 423 W and a peak energy transfer efficiency of 76.3%, both of which are significantly higher than those of two-graded concrete at the same slump. However, as a dense aggregate skeleton rapidly forms, the energy absorption efficiency of fully graded concrete decreases more rapidly during the middle and later stages of vibration, showing a characteristic pattern of “high initial absorption followed by rapid attenuation.” Through segregation assessment and porosity analysis, a safe vibration energy range for fully graded concrete was quantitatively determined, with lower and upper energy thresholds of 159.7 J·kg−1 and 538.5 J·kg−1, respectively. In addition, the experiments identified recommended vibration durations of 30–65 s and effective vibration influence radii of 22–85 mm for fully graded concrete under different slump conditions. These findings provide a quantitative basis for the control of vibration parameters and energy-oriented construction of fully graded concrete.
- Open Access
Concrete Mixture Cold Joint Prevention and Control System
To resolve the issue of cold joints forming in concrete during the construction process, this study has developed a control system with visual prevention capabilities. By utilizing the improved YOLO11-LP license plate recognition system, we record license plate information and calculate the supply time of the mixture. Based on the structural characteristics of the belt conveyor, laser ranging technology, and GNSS-RTK positioning technology, an algorithm is proposed to determine the operating status of the belt conveyor, calculate the position and area of the mixed material, and record the pouring and compaction time. This algorithm is suitable for parameter acquisition equipment throughout the entire process of mixture pouring. The developed software system is based on the parameters calculated by the pouring process time calculation model, combined with the cold joint prevention and control threshold of the mixture, and feeds back the construction warning information to the site through a visual model. The application proves that the developed preventive control system helps to avoid the formation of cold joints in the mixture.
Open AccessConcrete Mixture Cold Joint Prevention and Control System
To resolve the issue of cold joints forming in concrete during the construction process, this study has developed a control system with visual prevention capabilities. By utilizing the improved YOLO11-LP license plate recognition system, we record license plate information and calculate the supply time of the mixture. Based on the structural characteristics of the belt conveyor, laser ranging technology, and GNSS-RTK positioning technology, an algorithm is proposed to determine the operating status of the belt conveyor, calculate the position and area of the mixed material, and record the pouring and compaction time. This algorithm is suitable for parameter acquisition equipment throughout the entire process of mixture pouring. The developed software system is based on the parameters calculated by the pouring process time calculation model, combined with the cold joint prevention and control threshold of the mixture, and feeds back the construction warning information to the site through a visual model. The application proves that the developed preventive control system helps to avoid the formation of cold joints in the mixture.