Keun-Young Yook
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Keun-Young Yook has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Jungmok Seo
School of Electrical and Electronic Engineering Yonsei University Seoul Republic of Korea
2 shared publications - Tae Young Kim
School of Electrical and Electronic Engineering Yonsei University Seoul Republic of Korea
2 shared publications Yurim Lee
School of Electrical and Electronic Engineering Yonsei University Seoul Republic of Korea
2 shared publicationsChansoo Kim
School of Electrical and Electronic Engineering Yonsei University Seoul Republic of Korea
1 shared publicationCongqi Yang
Medical Research Center, Seoul National University, Seoul 03080, Republic of Korea
1 shared publication- Dong Gyu Lee
Department of Organic and Nano Engineering Hanyang University Seoul Republic of Korea
1 shared publication
Latest Publications
- Open Access
- 6 October 2026
- Published by Wiley in Advanced Science
- p. e78062
Synergistic Mechano‐Fluidic Self‐Fusion of Poly(Vinyl Alcohol)‐Modified Liquid‐Metal Particles for Post‐Treatment‐Free Soft Electronics
Liquid metals (LMs) are promising candidates for soft and stretchable conductors; however, their high surface tension and poor wettability pose significant challenges for high‐resolution printing. To address these limitations, LMs are commonly processed into liquid metal particles (LMPs), which improve printability. Nevertheless, the insulating oxide shell surrounding each particle persists, typically necessitating additional post‐treatment steps to achieve electrical conductivity. Here, we report synergistic mechano‐fluidic self‐fusion of poly(vinyl alcohol) (PVA)‐modified liquid‐metal particles (PmLMPs) for post‐treatment‐free soft interconnects. A sprayable PmLMP ink is formulated in which an ultrathin PVA shell stabilizes the particles and enhances substrate adhesion through hydrogen bonding. Direct electrical interconnection is achieved via a two‐stage process: spray‐induced mechanical impact ruptures the oxide shells to initiate metallic contact, followed by binary‐solvent‐driven Marangoni convection (deionized (DI) water/ethanol = 3:1 v/v) that promotes particle rearrangement and metallic neck growth. This mechano‐fluidic sequence enables rapid formation of conductive networks without post‐treatment. The printed films exhibit an initial conductivity of 1.5 × 10 6 S m − 1 , maintain electrical continuity under monotonic strains exceeding 200% and during approximately 1,400 stretch‐release cycles at 100% strain, and support 50 µm‐scale patterning with large‐area scalability. This work establishes a flow‐assisted metallic fusion approach for scalable, instantly conductive soft interconnects.
- 6 October 2026
- Published by Wiley in Advanced Science
- p. e78062
Open AccessSynergistic Mechano‐Fluidic Self‐Fusion of Poly(Vinyl Alcohol)‐Modified Liquid‐Metal Particles for Post‐Treatment‐Free Soft Electronics
Liquid metals (LMs) are promising candidates for soft and stretchable conductors; however, their high surface tension and poor wettability pose significant challenges for high‐resolution printing. To address these limitations, LMs are commonly processed into liquid metal particles (LMPs), which improve printability. Nevertheless, the insulating oxide shell surrounding each particle persists, typically necessitating additional post‐treatment steps to achieve electrical conductivity. Here, we report synergistic mechano‐fluidic self‐fusion of poly(vinyl alcohol) (PVA)‐modified liquid‐metal particles (PmLMPs) for post‐treatment‐free soft interconnects. A sprayable PmLMP ink is formulated in which an ultrathin PVA shell stabilizes the particles and enhances substrate adhesion through hydrogen bonding. Direct electrical interconnection is achieved via a two‐stage process: spray‐induced mechanical impact ruptures the oxide shells to initiate metallic contact, followed by binary‐solvent‐driven Marangoni convection (deionized (DI) water/ethanol = 3:1 v/v) that promotes particle rearrangement and metallic neck growth. This mechano‐fluidic sequence enables rapid formation of conductive networks without post‐treatment. The printed films exhibit an initial conductivity of 1.5 × 10 6 S m − 1 , maintain electrical continuity under monotonic strains exceeding 200% and during approximately 1,400 stretch‐release cycles at 100% strain, and support 50 µm‐scale patterning with large‐area scalability. This work establishes a flow‐assisted metallic fusion approach for scalable, instantly conductive soft interconnects.
- Open Access
- 12 September 2025
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 11 (37) , eadz1228
Bioadaptive liquid-infused multifunctional fibers for long-term neural recording via BDNF stabilization and enhanced neural interaction
Brain-computer interfaces (BCIs) enable direct communication between the brain and computers. However, their long-term functionality remains limited due to signal degradation caused by acute insertion trauma, chronic foreign body reaction (FBR), and biofouling at the device-tissue interface. To address these challenges, we introduce a multifunctional surface modification strategy called targeting-specific interaction and blocking nonspecific adhesion (TAB) coating for flexible fiber, achieving a synergistic integration of mechanical compliance and biochemical stability. The coating combines brain-derived neurotrophic factor (BDNF) conjugation and a lubricant-infused surface. This dual-functional design enables selective interaction with neurons and astrocytes while preventing nonspecific adhesion. Notably, high-quality single-unit neural signals were stably recorded for more than 12 months after implantation, demonstrating exceptional long-term recording performance. Integrating mechanical compatibility, antifouling properties, and selective neural cell interaction, the TAB-coated multifunctional fiber represents a transformative approach for neural implants, bridging biological systems with computational systems.
- 12 September 2025
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 11 (37) , eadz1228
Open AccessBioadaptive liquid-infused multifunctional fibers for long-term neural recording via BDNF stabilization and enhanced neural interaction
Brain-computer interfaces (BCIs) enable direct communication between the brain and computers. However, their long-term functionality remains limited due to signal degradation caused by acute insertion trauma, chronic foreign body reaction (FBR), and biofouling at the device-tissue interface. To address these challenges, we introduce a multifunctional surface modification strategy called targeting-specific interaction and blocking nonspecific adhesion (TAB) coating for flexible fiber, achieving a synergistic integration of mechanical compliance and biochemical stability. The coating combines brain-derived neurotrophic factor (BDNF) conjugation and a lubricant-infused surface. This dual-functional design enables selective interaction with neurons and astrocytes while preventing nonspecific adhesion. Notably, high-quality single-unit neural signals were stably recorded for more than 12 months after implantation, demonstrating exceptional long-term recording performance. Integrating mechanical compatibility, antifouling properties, and selective neural cell interaction, the TAB-coated multifunctional fiber represents a transformative approach for neural implants, bridging biological systems with computational systems.