David Holzer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
David Holzer has a total of 1 co-authors. Here are the top co-authors by number of shared publications:
- Gudrun Mikota
Johannes Kepler University Linz
2 shared publications
Latest Publications
- Open Access
Theoretical and Experimental Investigation of a Rotary Mechanical Pulsation Compensator for External Gear Pumps
Pressure pulsations generated by pumps impair noise behaviour, increase mechanical loading, and reduce control performance in hydraulic systems. This study investigates the use of a rotary mechanical pulsation compensator integrated into the drivetrain of an external gear pump. The aim is to attenuate pulsations directly at their source without modifying the hydraulic layout. This is accomplished by using the torque induced flow rate pulsation to cancel the external flow rate excitation, which leads to destructive interference between flow rate induced and torque induced pressure pulsations. An analytical frequency domain model of the coupled mechanical–hydraulic system is derived to determine the required stiffness and damping conditions. The theoretical results are validated experimentally at mean pressure levels of 100 bar and 170 bar, both for two different hydraulic layouts. With a resonator pipeline at the pump outlet, the first harmonic of the pressure pulsation at the compensation frequency is reduced by 10.9 bar and 18.4 bar, respectively, which corresponds to reduction rates of 93% and 98%. The required damping value depends on the operating conditions, but it is independent of the hydraulic layout. While insufficient damping increases pressure pulsations around the compensation frequency, slightly higher damping flattens the frequency characteristics of pressure pulsation and reduces the maxima around the compensation frequency. In the neighbourhood of this frequency, the proposed concept enables effective reduction of the first pressure pulsation harmonic through a structural modification of the drivetrain.
Open AccessTheoretical and Experimental Investigation of a Rotary Mechanical Pulsation Compensator for External Gear Pumps
Pressure pulsations generated by pumps impair noise behaviour, increase mechanical loading, and reduce control performance in hydraulic systems. This study investigates the use of a rotary mechanical pulsation compensator integrated into the drivetrain of an external gear pump. The aim is to attenuate pulsations directly at their source without modifying the hydraulic layout. This is accomplished by using the torque induced flow rate pulsation to cancel the external flow rate excitation, which leads to destructive interference between flow rate induced and torque induced pressure pulsations. An analytical frequency domain model of the coupled mechanical–hydraulic system is derived to determine the required stiffness and damping conditions. The theoretical results are validated experimentally at mean pressure levels of 100 bar and 170 bar, both for two different hydraulic layouts. With a resonator pipeline at the pump outlet, the first harmonic of the pressure pulsation at the compensation frequency is reduced by 10.9 bar and 18.4 bar, respectively, which corresponds to reduction rates of 93% and 98%. The required damping value depends on the operating conditions, but it is independent of the hydraulic layout. While insufficient damping increases pressure pulsations around the compensation frequency, slightly higher damping flattens the frequency characteristics of pressure pulsation and reduces the maxima around the compensation frequency. In the neighbourhood of this frequency, the proposed concept enables effective reduction of the first pressure pulsation harmonic through a structural modification of the drivetrain.
- Open Access
- 1 January 2025
- Published by River Publishers
- p. 142-152
Measurement of a rotary mechanical pulsation compensator under hydraulic resonance
If the pulsation frequency of a hydraulic pump or motor coincides with a natural frequency of the hydraulic system, there is a particular need for pulsation compensation. Under these conditions, a rotary mechanical pulsation compensator is investigated. The compensator consists in a torsional oscillator which is formed by the drivetrain of a radial piston pump and requires a special compensator coupling. At the pump outlet, two different hydraulic layouts are considered, including a closed pipeline and a cylinder chamber connected via a hose. Prior to experiments, simulations are conducted to determine system parameters at which a natural frequency of the hydraulic system matches the compensation frequency. In the experimental setup, the compensator coupling is installed on the pump shaft and driven by a speed-controlled induction motor. The measurements conducted with a closed pipeline show a pulsation reduction by a factor of more than three in the resonance case during a run-up test. Similar results are obtained in a run-up test with a cylinder in its limit stop position. An extension test with constant motor speed shows significant reduction of pressure pulsation. In the present configuration, the compensation effect is narrowband and the design of the coupling causes a dependency between compensation frequency and drivetrain torque.
- 1 January 2025
- Published by River Publishers
- p. 142-152
Open AccessMeasurement of a rotary mechanical pulsation compensator under hydraulic resonance
If the pulsation frequency of a hydraulic pump or motor coincides with a natural frequency of the hydraulic system, there is a particular need for pulsation compensation. Under these conditions, a rotary mechanical pulsation compensator is investigated. The compensator consists in a torsional oscillator which is formed by the drivetrain of a radial piston pump and requires a special compensator coupling. At the pump outlet, two different hydraulic layouts are considered, including a closed pipeline and a cylinder chamber connected via a hose. Prior to experiments, simulations are conducted to determine system parameters at which a natural frequency of the hydraulic system matches the compensation frequency. In the experimental setup, the compensator coupling is installed on the pump shaft and driven by a speed-controlled induction motor. The measurements conducted with a closed pipeline show a pulsation reduction by a factor of more than three in the resonance case during a run-up test. Similar results are obtained in a run-up test with a cylinder in its limit stop position. An extension test with constant motor speed shows significant reduction of pressure pulsation. In the present configuration, the compensation effect is narrowband and the design of the coupling causes a dependency between compensation frequency and drivetrain torque.